1 #
2 # (C) Copyright 2000 - 2012
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
4 #
5 # See file CREDITS for list of people who contributed to this
6 # project.
7 #
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
12 #
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
17 #
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21 # MA 02111-1307 USA
22 #
24 Summary:
25 ========
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
31 code.
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
46 Status:
47 =======
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port. The MAINTAINERS file lists board
55 maintainers.
57 Note: There is no CHANGELOG file in the actual U-Boot source tree;
58 it can be created dynamically from the Git log using:
60 make CHANGELOG
63 Where to get help:
64 ==================
66 In case you have questions about, problems with or contributions for
67 U-Boot you should send a message to the U-Boot mailing list at
68 <u-boot@lists.denx.de>. There is also an archive of previous traffic
69 on the mailing list - please search the archive before asking FAQ's.
70 Please see http://lists.denx.de/pipermail/u-boot and
71 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
74 Where to get source code:
75 =========================
77 The U-Boot source code is maintained in the git repository at
78 git://www.denx.de/git/u-boot.git ; you can browse it online at
79 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
81 The "snapshot" links on this page allow you to download tarballs of
82 any version you might be interested in. Official releases are also
83 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
84 directory.
86 Pre-built (and tested) images are available from
87 ftp://ftp.denx.de/pub/u-boot/images/
90 Where we come from:
91 ===================
93 - start from 8xxrom sources
94 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
95 - clean up code
96 - make it easier to add custom boards
97 - make it possible to add other [PowerPC] CPUs
98 - extend functions, especially:
99 * Provide extended interface to Linux boot loader
100 * S-Record download
101 * network boot
102 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
103 - create ARMBoot project (http://sourceforge.net/projects/armboot)
104 - add other CPU families (starting with ARM)
105 - create U-Boot project (http://sourceforge.net/projects/u-boot)
106 - current project page: see http://www.denx.de/wiki/U-Boot
109 Names and Spelling:
110 ===================
112 The "official" name of this project is "Das U-Boot". The spelling
113 "U-Boot" shall be used in all written text (documentation, comments
114 in source files etc.). Example:
116 This is the README file for the U-Boot project.
118 File names etc. shall be based on the string "u-boot". Examples:
120 include/asm-ppc/u-boot.h
122 #include <asm/u-boot.h>
124 Variable names, preprocessor constants etc. shall be either based on
125 the string "u_boot" or on "U_BOOT". Example:
127 U_BOOT_VERSION u_boot_logo
128 IH_OS_U_BOOT u_boot_hush_start
131 Versioning:
132 ===========
134 Starting with the release in October 2008, the names of the releases
135 were changed from numerical release numbers without deeper meaning
136 into a time stamp based numbering. Regular releases are identified by
137 names consisting of the calendar year and month of the release date.
138 Additional fields (if present) indicate release candidates or bug fix
139 releases in "stable" maintenance trees.
141 Examples:
142 U-Boot v2009.11 - Release November 2009
143 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
144 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
147 Directory Hierarchy:
148 ====================
150 /arch Architecture specific files
151 /arm Files generic to ARM architecture
152 /cpu CPU specific files
153 /arm720t Files specific to ARM 720 CPUs
154 /arm920t Files specific to ARM 920 CPUs
155 /at91 Files specific to Atmel AT91RM9200 CPU
156 /imx Files specific to Freescale MC9328 i.MX CPUs
157 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
158 /arm925t Files specific to ARM 925 CPUs
159 /arm926ejs Files specific to ARM 926 CPUs
160 /arm1136 Files specific to ARM 1136 CPUs
161 /ixp Files specific to Intel XScale IXP CPUs
162 /pxa Files specific to Intel XScale PXA CPUs
163 /s3c44b0 Files specific to Samsung S3C44B0 CPUs
164 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
165 /lib Architecture specific library files
166 /avr32 Files generic to AVR32 architecture
167 /cpu CPU specific files
168 /lib Architecture specific library files
169 /blackfin Files generic to Analog Devices Blackfin architecture
170 /cpu CPU specific files
171 /lib Architecture specific library files
172 /x86 Files generic to x86 architecture
173 /cpu CPU specific files
174 /lib Architecture specific library files
175 /m68k Files generic to m68k architecture
176 /cpu CPU specific files
177 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
178 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
179 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
180 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
181 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
182 /lib Architecture specific library files
183 /microblaze Files generic to microblaze architecture
184 /cpu CPU specific files
185 /lib Architecture specific library files
186 /mips Files generic to MIPS architecture
187 /cpu CPU specific files
188 /mips32 Files specific to MIPS32 CPUs
189 /xburst Files specific to Ingenic XBurst CPUs
190 /lib Architecture specific library files
191 /nds32 Files generic to NDS32 architecture
192 /cpu CPU specific files
193 /n1213 Files specific to Andes Technology N1213 CPUs
194 /lib Architecture specific library files
195 /nios2 Files generic to Altera NIOS2 architecture
196 /cpu CPU specific files
197 /lib Architecture specific library files
198 /powerpc Files generic to PowerPC architecture
199 /cpu CPU specific files
200 /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
201 /mpc5xx Files specific to Freescale MPC5xx CPUs
202 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
203 /mpc8xx Files specific to Freescale MPC8xx CPUs
204 /mpc8220 Files specific to Freescale MPC8220 CPUs
205 /mpc824x Files specific to Freescale MPC824x CPUs
206 /mpc8260 Files specific to Freescale MPC8260 CPUs
207 /mpc85xx Files specific to Freescale MPC85xx CPUs
208 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
209 /lib Architecture specific library files
210 /sh Files generic to SH architecture
211 /cpu CPU specific files
212 /sh2 Files specific to sh2 CPUs
213 /sh3 Files specific to sh3 CPUs
214 /sh4 Files specific to sh4 CPUs
215 /lib Architecture specific library files
216 /sparc Files generic to SPARC architecture
217 /cpu CPU specific files
218 /leon2 Files specific to Gaisler LEON2 SPARC CPU
219 /leon3 Files specific to Gaisler LEON3 SPARC CPU
220 /lib Architecture specific library files
221 /api Machine/arch independent API for external apps
222 /board Board dependent files
223 /common Misc architecture independent functions
224 /disk Code for disk drive partition handling
225 /doc Documentation (don't expect too much)
226 /drivers Commonly used device drivers
227 /examples Example code for standalone applications, etc.
228 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
229 /include Header Files
230 /lib Files generic to all architectures
231 /libfdt Library files to support flattened device trees
232 /lzma Library files to support LZMA decompression
233 /lzo Library files to support LZO decompression
234 /net Networking code
235 /post Power On Self Test
236 /rtc Real Time Clock drivers
237 /tools Tools to build S-Record or U-Boot images, etc.
239 Software Configuration:
240 =======================
242 Configuration is usually done using C preprocessor defines; the
243 rationale behind that is to avoid dead code whenever possible.
245 There are two classes of configuration variables:
247 * Configuration _OPTIONS_:
248 These are selectable by the user and have names beginning with
249 "CONFIG_".
251 * Configuration _SETTINGS_:
252 These depend on the hardware etc. and should not be meddled with if
253 you don't know what you're doing; they have names beginning with
254 "CONFIG_SYS_".
256 Later we will add a configuration tool - probably similar to or even
257 identical to what's used for the Linux kernel. Right now, we have to
258 do the configuration by hand, which means creating some symbolic
259 links and editing some configuration files. We use the TQM8xxL boards
260 as an example here.
263 Selection of Processor Architecture and Board Type:
264 ---------------------------------------------------
266 For all supported boards there are ready-to-use default
267 configurations available; just type "make <board_name>_config".
269 Example: For a TQM823L module type:
271 cd u-boot
272 make TQM823L_config
274 For the Cogent platform, you need to specify the CPU type as well;
275 e.g. "make cogent_mpc8xx_config". And also configure the cogent
276 directory according to the instructions in cogent/README.
279 Configuration Options:
280 ----------------------
282 Configuration depends on the combination of board and CPU type; all
283 such information is kept in a configuration file
284 "include/configs/<board_name>.h".
286 Example: For a TQM823L module, all configuration settings are in
287 "include/configs/TQM823L.h".
290 Many of the options are named exactly as the corresponding Linux
291 kernel configuration options. The intention is to make it easier to
292 build a config tool - later.
295 The following options need to be configured:
297 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
299 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
301 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
302 Define exactly one, e.g. CONFIG_ATSTK1002
304 - CPU Module Type: (if CONFIG_COGENT is defined)
305 Define exactly one of
306 CONFIG_CMA286_60_OLD
307 --- FIXME --- not tested yet:
308 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
309 CONFIG_CMA287_23, CONFIG_CMA287_50
311 - Motherboard Type: (if CONFIG_COGENT is defined)
312 Define exactly one of
313 CONFIG_CMA101, CONFIG_CMA102
315 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
316 Define one or more of
317 CONFIG_CMA302
319 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
320 Define one or more of
321 CONFIG_LCD_HEARTBEAT - update a character position on
322 the LCD display every second with
323 a "rotator" |\-/|\-/
325 - Board flavour: (if CONFIG_MPC8260ADS is defined)
326 CONFIG_ADSTYPE
327 Possible values are:
328 CONFIG_SYS_8260ADS - original MPC8260ADS
329 CONFIG_SYS_8266ADS - MPC8266ADS
330 CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
331 CONFIG_SYS_8272ADS - MPC8272ADS
333 - Marvell Family Member
334 CONFIG_SYS_MVFS - define it if you want to enable
335 multiple fs option at one time
336 for marvell soc family
338 - MPC824X Family Member (if CONFIG_MPC824X is defined)
339 Define exactly one of
340 CONFIG_MPC8240, CONFIG_MPC8245
342 - 8xx CPU Options: (if using an MPC8xx CPU)
343 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
344 get_gclk_freq() cannot work
345 e.g. if there is no 32KHz
346 reference PIT/RTC clock
347 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
348 or XTAL/EXTAL)
350 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
351 CONFIG_SYS_8xx_CPUCLK_MIN
352 CONFIG_SYS_8xx_CPUCLK_MAX
353 CONFIG_8xx_CPUCLK_DEFAULT
354 See doc/README.MPC866
356 CONFIG_SYS_MEASURE_CPUCLK
358 Define this to measure the actual CPU clock instead
359 of relying on the correctness of the configured
360 values. Mostly useful for board bringup to make sure
361 the PLL is locked at the intended frequency. Note
362 that this requires a (stable) reference clock (32 kHz
363 RTC clock or CONFIG_SYS_8XX_XIN)
365 CONFIG_SYS_DELAYED_ICACHE
367 Define this option if you want to enable the
368 ICache only when Code runs from RAM.
370 - 85xx CPU Options:
371 CONFIG_SYS_PPC64
373 Specifies that the core is a 64-bit PowerPC implementation (implements
374 the "64" category of the Power ISA). This is necessary for ePAPR
375 compliance, among other possible reasons.
377 CONFIG_SYS_FSL_TBCLK_DIV
379 Defines the core time base clock divider ratio compared to the
380 system clock. On most PQ3 devices this is 8, on newer QorIQ
381 devices it can be 16 or 32. The ratio varies from SoC to Soc.
383 CONFIG_SYS_FSL_PCIE_COMPAT
385 Defines the string to utilize when trying to match PCIe device
386 tree nodes for the given platform.
388 CONFIG_SYS_PPC_E500_DEBUG_TLB
390 Enables a temporary TLB entry to be used during boot to work
391 around limitations in e500v1 and e500v2 external debugger
392 support. This reduces the portions of the boot code where
393 breakpoints and single stepping do not work. The value of this
394 symbol should be set to the TLB1 entry to be used for this
395 purpose.
397 CONFIG_SYS_FSL_ERRATUM_A004510
399 Enables a workaround for erratum A004510. If set,
400 then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
401 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
403 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
404 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
406 Defines one or two SoC revisions (low 8 bits of SVR)
407 for which the A004510 workaround should be applied.
409 The rest of SVR is either not relevant to the decision
410 of whether the erratum is present (e.g. p2040 versus
411 p2041) or is implied by the build target, which controls
412 whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
414 See Freescale App Note 4493 for more information about
415 this erratum.
417 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
419 This is the value to write into CCSR offset 0x18600
420 according to the A004510 workaround.
422 - Generic CPU options:
423 CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
425 Defines the endianess of the CPU. Implementation of those
426 values is arch specific.
428 - Intel Monahans options:
429 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
431 Defines the Monahans run mode to oscillator
432 ratio. Valid values are 8, 16, 24, 31. The core
433 frequency is this value multiplied by 13 MHz.
435 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
437 Defines the Monahans turbo mode to oscillator
438 ratio. Valid values are 1 (default if undefined) and
439 2. The core frequency as calculated above is multiplied
440 by this value.
442 - MIPS CPU options:
443 CONFIG_SYS_INIT_SP_OFFSET
445 Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
446 pointer. This is needed for the temporary stack before
447 relocation.
449 CONFIG_SYS_MIPS_CACHE_MODE
451 Cache operation mode for the MIPS CPU.
452 See also arch/mips/include/asm/mipsregs.h.
453 Possible values are:
454 CONF_CM_CACHABLE_NO_WA
455 CONF_CM_CACHABLE_WA
456 CONF_CM_UNCACHED
457 CONF_CM_CACHABLE_NONCOHERENT
458 CONF_CM_CACHABLE_CE
459 CONF_CM_CACHABLE_COW
460 CONF_CM_CACHABLE_CUW
461 CONF_CM_CACHABLE_ACCELERATED
463 CONFIG_SYS_XWAY_EBU_BOOTCFG
465 Special option for Lantiq XWAY SoCs for booting from NOR flash.
466 See also arch/mips/cpu/mips32/start.S.
468 CONFIG_XWAY_SWAP_BYTES
470 Enable compilation of tools/xway-swap-bytes needed for Lantiq
471 XWAY SoCs for booting from NOR flash. The U-Boot image needs to
472 be swapped if a flash programmer is used.
474 - ARM options:
475 CONFIG_SYS_EXCEPTION_VECTORS_HIGH
477 Select high exception vectors of the ARM core, e.g., do not
478 clear the V bit of the c1 register of CP15.
480 CONFIG_SYS_THUMB_BUILD
482 Use this flag to build U-Boot using the Thumb instruction
483 set for ARM architectures. Thumb instruction set provides
484 better code density. For ARM architectures that support
485 Thumb2 this flag will result in Thumb2 code generated by
486 GCC.
488 - Linux Kernel Interface:
489 CONFIG_CLOCKS_IN_MHZ
491 U-Boot stores all clock information in Hz
492 internally. For binary compatibility with older Linux
493 kernels (which expect the clocks passed in the
494 bd_info data to be in MHz) the environment variable
495 "clocks_in_mhz" can be defined so that U-Boot
496 converts clock data to MHZ before passing it to the
497 Linux kernel.
498 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
499 "clocks_in_mhz=1" is automatically included in the
500 default environment.
502 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
504 When transferring memsize parameter to linux, some versions
505 expect it to be in bytes, others in MB.
506 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
508 CONFIG_OF_LIBFDT
510 New kernel versions are expecting firmware settings to be
511 passed using flattened device trees (based on open firmware
512 concepts).
514 CONFIG_OF_LIBFDT
515 * New libfdt-based support
516 * Adds the "fdt" command
517 * The bootm command automatically updates the fdt
519 OF_CPU - The proper name of the cpus node (only required for
520 MPC512X and MPC5xxx based boards).
521 OF_SOC - The proper name of the soc node (only required for
522 MPC512X and MPC5xxx based boards).
523 OF_TBCLK - The timebase frequency.
524 OF_STDOUT_PATH - The path to the console device
526 boards with QUICC Engines require OF_QE to set UCC MAC
527 addresses
529 CONFIG_OF_BOARD_SETUP
531 Board code has addition modification that it wants to make
532 to the flat device tree before handing it off to the kernel
534 CONFIG_OF_BOOT_CPU
536 This define fills in the correct boot CPU in the boot
537 param header, the default value is zero if undefined.
539 CONFIG_OF_IDE_FIXUP
541 U-Boot can detect if an IDE device is present or not.
542 If not, and this new config option is activated, U-Boot
543 removes the ATA node from the DTS before booting Linux,
544 so the Linux IDE driver does not probe the device and
545 crash. This is needed for buggy hardware (uc101) where
546 no pull down resistor is connected to the signal IDE5V_DD7.
548 CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
550 This setting is mandatory for all boards that have only one
551 machine type and must be used to specify the machine type
552 number as it appears in the ARM machine registry
553 (see http://www.arm.linux.org.uk/developer/machines/).
554 Only boards that have multiple machine types supported
555 in a single configuration file and the machine type is
556 runtime discoverable, do not have to use this setting.
558 - vxWorks boot parameters:
560 bootvx constructs a valid bootline using the following
561 environments variables: bootfile, ipaddr, serverip, hostname.
562 It loads the vxWorks image pointed bootfile.
564 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
565 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
566 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
567 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
569 CONFIG_SYS_VXWORKS_ADD_PARAMS
571 Add it at the end of the bootline. E.g "u=username pw=secret"
573 Note: If a "bootargs" environment is defined, it will overwride
574 the defaults discussed just above.
576 - Cache Configuration:
577 CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
578 CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
579 CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
581 - Cache Configuration for ARM:
582 CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
583 controller
584 CONFIG_SYS_PL310_BASE - Physical base address of PL310
585 controller register space
587 - Serial Ports:
588 CONFIG_PL010_SERIAL
590 Define this if you want support for Amba PrimeCell PL010 UARTs.
592 CONFIG_PL011_SERIAL
594 Define this if you want support for Amba PrimeCell PL011 UARTs.
596 CONFIG_PL011_CLOCK
598 If you have Amba PrimeCell PL011 UARTs, set this variable to
599 the clock speed of the UARTs.
601 CONFIG_PL01x_PORTS
603 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
604 define this to a list of base addresses for each (supported)
605 port. See e.g. include/configs/versatile.h
607 CONFIG_PL011_SERIAL_RLCR
609 Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
610 have separate receive and transmit line control registers. Set
611 this variable to initialize the extra register.
613 CONFIG_PL011_SERIAL_FLUSH_ON_INIT
615 On some platforms (e.g. U8500) U-Boot is loaded by a second stage
616 boot loader that has already initialized the UART. Define this
617 variable to flush the UART at init time.
620 - Console Interface:
621 Depending on board, define exactly one serial port
622 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
623 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
624 console by defining CONFIG_8xx_CONS_NONE
626 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
627 port routines must be defined elsewhere
628 (i.e. serial_init(), serial_getc(), ...)
630 CONFIG_CFB_CONSOLE
631 Enables console device for a color framebuffer. Needs following
632 defines (cf. smiLynxEM, i8042)
633 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
634 (default big endian)
635 VIDEO_HW_RECTFILL graphic chip supports
636 rectangle fill
637 (cf. smiLynxEM)
638 VIDEO_HW_BITBLT graphic chip supports
639 bit-blit (cf. smiLynxEM)
640 VIDEO_VISIBLE_COLS visible pixel columns
641 (cols=pitch)
642 VIDEO_VISIBLE_ROWS visible pixel rows
643 VIDEO_PIXEL_SIZE bytes per pixel
644 VIDEO_DATA_FORMAT graphic data format
645 (0-5, cf. cfb_console.c)
646 VIDEO_FB_ADRS framebuffer address
647 VIDEO_KBD_INIT_FCT keyboard int fct
648 (i.e. i8042_kbd_init())
649 VIDEO_TSTC_FCT test char fct
650 (i.e. i8042_tstc)
651 VIDEO_GETC_FCT get char fct
652 (i.e. i8042_getc)
653 CONFIG_CONSOLE_CURSOR cursor drawing on/off
654 (requires blink timer
655 cf. i8042.c)
656 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
657 CONFIG_CONSOLE_TIME display time/date info in
658 upper right corner
659 (requires CONFIG_CMD_DATE)
660 CONFIG_VIDEO_LOGO display Linux logo in
661 upper left corner
662 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
663 linux_logo.h for logo.
664 Requires CONFIG_VIDEO_LOGO
665 CONFIG_CONSOLE_EXTRA_INFO
666 additional board info beside
667 the logo
669 When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
670 a limited number of ANSI escape sequences (cursor control,
671 erase functions and limited graphics rendition control).
673 When CONFIG_CFB_CONSOLE is defined, video console is
674 default i/o. Serial console can be forced with
675 environment 'console=serial'.
677 When CONFIG_SILENT_CONSOLE is defined, all console
678 messages (by U-Boot and Linux!) can be silenced with
679 the "silent" environment variable. See
680 doc/README.silent for more information.
682 - Console Baudrate:
683 CONFIG_BAUDRATE - in bps
684 Select one of the baudrates listed in
685 CONFIG_SYS_BAUDRATE_TABLE, see below.
686 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
688 - Console Rx buffer length
689 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
690 the maximum receive buffer length for the SMC.
691 This option is actual only for 82xx and 8xx possible.
692 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
693 must be defined, to setup the maximum idle timeout for
694 the SMC.
696 - Pre-Console Buffer:
697 Prior to the console being initialised (i.e. serial UART
698 initialised etc) all console output is silently discarded.
699 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
700 buffer any console messages prior to the console being
701 initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
702 bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
703 a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
704 bytes are output before the console is initialised, the
705 earlier bytes are discarded.
707 'Sane' compilers will generate smaller code if
708 CONFIG_PRE_CON_BUF_SZ is a power of 2
710 - Safe printf() functions
711 Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
712 the printf() functions. These are defined in
713 include/vsprintf.h and include snprintf(), vsnprintf() and
714 so on. Code size increase is approximately 300-500 bytes.
715 If this option is not given then these functions will
716 silently discard their buffer size argument - this means
717 you are not getting any overflow checking in this case.
719 - Boot Delay: CONFIG_BOOTDELAY - in seconds
720 Delay before automatically booting the default image;
721 set to -1 to disable autoboot.
722 set to -2 to autoboot with no delay and not check for abort
723 (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
725 See doc/README.autoboot for these options that
726 work with CONFIG_BOOTDELAY. None are required.
727 CONFIG_BOOT_RETRY_TIME
728 CONFIG_BOOT_RETRY_MIN
729 CONFIG_AUTOBOOT_KEYED
730 CONFIG_AUTOBOOT_PROMPT
731 CONFIG_AUTOBOOT_DELAY_STR
732 CONFIG_AUTOBOOT_STOP_STR
733 CONFIG_AUTOBOOT_DELAY_STR2
734 CONFIG_AUTOBOOT_STOP_STR2
735 CONFIG_ZERO_BOOTDELAY_CHECK
736 CONFIG_RESET_TO_RETRY
738 - Autoboot Command:
739 CONFIG_BOOTCOMMAND
740 Only needed when CONFIG_BOOTDELAY is enabled;
741 define a command string that is automatically executed
742 when no character is read on the console interface
743 within "Boot Delay" after reset.
745 CONFIG_BOOTARGS
746 This can be used to pass arguments to the bootm
747 command. The value of CONFIG_BOOTARGS goes into the
748 environment value "bootargs".
750 CONFIG_RAMBOOT and CONFIG_NFSBOOT
751 The value of these goes into the environment as
752 "ramboot" and "nfsboot" respectively, and can be used
753 as a convenience, when switching between booting from
754 RAM and NFS.
756 - Pre-Boot Commands:
757 CONFIG_PREBOOT
759 When this option is #defined, the existence of the
760 environment variable "preboot" will be checked
761 immediately before starting the CONFIG_BOOTDELAY
762 countdown and/or running the auto-boot command resp.
763 entering interactive mode.
765 This feature is especially useful when "preboot" is
766 automatically generated or modified. For an example
767 see the LWMON board specific code: here "preboot" is
768 modified when the user holds down a certain
769 combination of keys on the (special) keyboard when
770 booting the systems
772 - Serial Download Echo Mode:
773 CONFIG_LOADS_ECHO
774 If defined to 1, all characters received during a
775 serial download (using the "loads" command) are
776 echoed back. This might be needed by some terminal
777 emulations (like "cu"), but may as well just take
778 time on others. This setting #define's the initial
779 value of the "loads_echo" environment variable.
781 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
782 CONFIG_KGDB_BAUDRATE
783 Select one of the baudrates listed in
784 CONFIG_SYS_BAUDRATE_TABLE, see below.
786 - Monitor Functions:
787 Monitor commands can be included or excluded
788 from the build by using the #include files
789 <config_cmd_all.h> and #undef'ing unwanted
790 commands, or using <config_cmd_default.h>
791 and augmenting with additional #define's
792 for wanted commands.
794 The default command configuration includes all commands
795 except those marked below with a "*".
797 CONFIG_CMD_ASKENV * ask for env variable
798 CONFIG_CMD_BDI bdinfo
799 CONFIG_CMD_BEDBUG * Include BedBug Debugger
800 CONFIG_CMD_BMP * BMP support
801 CONFIG_CMD_BSP * Board specific commands
802 CONFIG_CMD_BOOTD bootd
803 CONFIG_CMD_CACHE * icache, dcache
804 CONFIG_CMD_CONSOLE coninfo
805 CONFIG_CMD_CRC32 * crc32
806 CONFIG_CMD_DATE * support for RTC, date/time...
807 CONFIG_CMD_DHCP * DHCP support
808 CONFIG_CMD_DIAG * Diagnostics
809 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
810 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
811 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
812 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
813 CONFIG_CMD_DTT * Digital Therm and Thermostat
814 CONFIG_CMD_ECHO echo arguments
815 CONFIG_CMD_EDITENV edit env variable
816 CONFIG_CMD_EEPROM * EEPROM read/write support
817 CONFIG_CMD_ELF * bootelf, bootvx
818 CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
819 CONFIG_CMD_ENV_FLAGS * display details about env flags
820 CONFIG_CMD_EXPORTENV * export the environment
821 CONFIG_CMD_EXT2 * ext2 command support
822 CONFIG_CMD_EXT4 * ext4 command support
823 CONFIG_CMD_SAVEENV saveenv
824 CONFIG_CMD_FDC * Floppy Disk Support
825 CONFIG_CMD_FAT * FAT command support
826 CONFIG_CMD_FDOS * Dos diskette Support
827 CONFIG_CMD_FLASH flinfo, erase, protect
828 CONFIG_CMD_FPGA FPGA device initialization support
829 CONFIG_CMD_GETTIME * Get time since boot
830 CONFIG_CMD_GO * the 'go' command (exec code)
831 CONFIG_CMD_GREPENV * search environment
832 CONFIG_CMD_HASH * calculate hash / digest
833 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
834 CONFIG_CMD_I2C * I2C serial bus support
835 CONFIG_CMD_IDE * IDE harddisk support
836 CONFIG_CMD_IMI iminfo
837 CONFIG_CMD_IMLS List all found images
838 CONFIG_CMD_IMMAP * IMMR dump support
839 CONFIG_CMD_IMPORTENV * import an environment
840 CONFIG_CMD_INI * import data from an ini file into the env
841 CONFIG_CMD_IRQ * irqinfo
842 CONFIG_CMD_ITEST Integer/string test of 2 values
843 CONFIG_CMD_JFFS2 * JFFS2 Support
844 CONFIG_CMD_KGDB * kgdb
845 CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
846 CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
847 (169.254.*.*)
848 CONFIG_CMD_LOADB loadb
849 CONFIG_CMD_LOADS loads
850 CONFIG_CMD_MD5SUM print md5 message digest
851 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
852 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
853 loop, loopw, mtest
854 CONFIG_CMD_MISC Misc functions like sleep etc
855 CONFIG_CMD_MMC * MMC memory mapped support
856 CONFIG_CMD_MII * MII utility commands
857 CONFIG_CMD_MTDPARTS * MTD partition support
858 CONFIG_CMD_NAND * NAND support
859 CONFIG_CMD_NET bootp, tftpboot, rarpboot
860 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
861 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
862 CONFIG_CMD_PCI * pciinfo
863 CONFIG_CMD_PCMCIA * PCMCIA support
864 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
865 host
866 CONFIG_CMD_PORTIO * Port I/O
867 CONFIG_CMD_READ * Read raw data from partition
868 CONFIG_CMD_REGINFO * Register dump
869 CONFIG_CMD_RUN run command in env variable
870 CONFIG_CMD_SAVES * save S record dump
871 CONFIG_CMD_SCSI * SCSI Support
872 CONFIG_CMD_SDRAM * print SDRAM configuration information
873 (requires CONFIG_CMD_I2C)
874 CONFIG_CMD_SETGETDCR Support for DCR Register access
875 (4xx only)
876 CONFIG_CMD_SF * Read/write/erase SPI NOR flash
877 CONFIG_CMD_SHA1SUM print sha1 memory digest
878 (requires CONFIG_CMD_MEMORY)
879 CONFIG_CMD_SOURCE "source" command Support
880 CONFIG_CMD_SPI * SPI serial bus support
881 CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
882 CONFIG_CMD_TFTPPUT * TFTP put command (upload)
883 CONFIG_CMD_TIME * run command and report execution time (ARM specific)
884 CONFIG_CMD_TIMER * access to the system tick timer
885 CONFIG_CMD_USB * USB support
886 CONFIG_CMD_CDP * Cisco Discover Protocol support
887 CONFIG_CMD_MFSL * Microblaze FSL support
890 EXAMPLE: If you want all functions except of network
891 support you can write:
893 #include "config_cmd_all.h"
894 #undef CONFIG_CMD_NET
896 Other Commands:
897 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
899 Note: Don't enable the "icache" and "dcache" commands
900 (configuration option CONFIG_CMD_CACHE) unless you know
901 what you (and your U-Boot users) are doing. Data
902 cache cannot be enabled on systems like the 8xx or
903 8260 (where accesses to the IMMR region must be
904 uncached), and it cannot be disabled on all other
905 systems where we (mis-) use the data cache to hold an
906 initial stack and some data.
909 XXX - this list needs to get updated!
911 - Device tree:
912 CONFIG_OF_CONTROL
913 If this variable is defined, U-Boot will use a device tree
914 to configure its devices, instead of relying on statically
915 compiled #defines in the board file. This option is
916 experimental and only available on a few boards. The device
917 tree is available in the global data as gd->fdt_blob.
919 U-Boot needs to get its device tree from somewhere. This can
920 be done using one of the two options below:
922 CONFIG_OF_EMBED
923 If this variable is defined, U-Boot will embed a device tree
924 binary in its image. This device tree file should be in the
925 board directory and called <soc>-<board>.dts. The binary file
926 is then picked up in board_init_f() and made available through
927 the global data structure as gd->blob.
929 CONFIG_OF_SEPARATE
930 If this variable is defined, U-Boot will build a device tree
931 binary. It will be called u-boot.dtb. Architecture-specific
932 code will locate it at run-time. Generally this works by:
934 cat u-boot.bin u-boot.dtb >image.bin
936 and in fact, U-Boot does this for you, creating a file called
937 u-boot-dtb.bin which is useful in the common case. You can
938 still use the individual files if you need something more
939 exotic.
941 - Watchdog:
942 CONFIG_WATCHDOG
943 If this variable is defined, it enables watchdog
944 support for the SoC. There must be support in the SoC
945 specific code for a watchdog. For the 8xx and 8260
946 CPUs, the SIU Watchdog feature is enabled in the SYPCR
947 register. When supported for a specific SoC is
948 available, then no further board specific code should
949 be needed to use it.
951 CONFIG_HW_WATCHDOG
952 When using a watchdog circuitry external to the used
953 SoC, then define this variable and provide board
954 specific code for the "hw_watchdog_reset" function.
956 - U-Boot Version:
957 CONFIG_VERSION_VARIABLE
958 If this variable is defined, an environment variable
959 named "ver" is created by U-Boot showing the U-Boot
960 version as printed by the "version" command.
961 Any change to this variable will be reverted at the
962 next reset.
964 - Real-Time Clock:
966 When CONFIG_CMD_DATE is selected, the type of the RTC
967 has to be selected, too. Define exactly one of the
968 following options:
970 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
971 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
972 CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
973 CONFIG_RTC_MC146818 - use MC146818 RTC
974 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
975 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
976 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
977 CONFIG_RTC_DS164x - use Dallas DS164x RTC
978 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
979 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
980 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
981 CONFIG_SYS_RV3029_TCR - enable trickle charger on
982 RV3029 RTC.
984 Note that if the RTC uses I2C, then the I2C interface
985 must also be configured. See I2C Support, below.
987 - GPIO Support:
988 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
989 CONFIG_PCA953X_INFO - enable pca953x info command
991 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
992 chip-ngpio pairs that tell the PCA953X driver the number of
993 pins supported by a particular chip.
995 Note that if the GPIO device uses I2C, then the I2C interface
996 must also be configured. See I2C Support, below.
998 - Timestamp Support:
1000 When CONFIG_TIMESTAMP is selected, the timestamp
1001 (date and time) of an image is printed by image
1002 commands like bootm or iminfo. This option is
1003 automatically enabled when you select CONFIG_CMD_DATE .
1005 - Partition Labels (disklabels) Supported:
1006 Zero or more of the following:
1007 CONFIG_MAC_PARTITION Apple's MacOS partition table.
1008 CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
1009 Intel architecture, USB sticks, etc.
1010 CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
1011 CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
1012 bootloader. Note 2TB partition limit; see
1013 disk/part_efi.c
1014 CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
1016 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
1017 CONFIG_CMD_SCSI) you must configure support for at
1018 least one non-MTD partition type as well.
1020 - IDE Reset method:
1021 CONFIG_IDE_RESET_ROUTINE - this is defined in several
1022 board configurations files but used nowhere!
1024 CONFIG_IDE_RESET - is this is defined, IDE Reset will
1025 be performed by calling the function
1026 ide_set_reset(int reset)
1027 which has to be defined in a board specific file
1029 - ATAPI Support:
1030 CONFIG_ATAPI
1032 Set this to enable ATAPI support.
1034 - LBA48 Support
1035 CONFIG_LBA48
1037 Set this to enable support for disks larger than 137GB
1038 Also look at CONFIG_SYS_64BIT_LBA.
1039 Whithout these , LBA48 support uses 32bit variables and will 'only'
1040 support disks up to 2.1TB.
1042 CONFIG_SYS_64BIT_LBA:
1043 When enabled, makes the IDE subsystem use 64bit sector addresses.
1044 Default is 32bit.
1046 - SCSI Support:
1047 At the moment only there is only support for the
1048 SYM53C8XX SCSI controller; define
1049 CONFIG_SCSI_SYM53C8XX to enable it.
1051 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
1052 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
1053 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
1054 maximum numbers of LUNs, SCSI ID's and target
1055 devices.
1056 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
1058 The environment variable 'scsidevs' is set to the number of
1059 SCSI devices found during the last scan.
1061 - NETWORK Support (PCI):
1062 CONFIG_E1000
1063 Support for Intel 8254x/8257x gigabit chips.
1065 CONFIG_E1000_SPI
1066 Utility code for direct access to the SPI bus on Intel 8257x.
1067 This does not do anything useful unless you set at least one
1068 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
1070 CONFIG_E1000_SPI_GENERIC
1071 Allow generic access to the SPI bus on the Intel 8257x, for
1072 example with the "sspi" command.
1074 CONFIG_CMD_E1000
1075 Management command for E1000 devices. When used on devices
1076 with SPI support you can reprogram the EEPROM from U-Boot.
1078 CONFIG_E1000_FALLBACK_MAC
1079 default MAC for empty EEPROM after production.
1081 CONFIG_EEPRO100
1082 Support for Intel 82557/82559/82559ER chips.
1083 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
1084 write routine for first time initialisation.
1086 CONFIG_TULIP
1087 Support for Digital 2114x chips.
1088 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
1089 modem chip initialisation (KS8761/QS6611).
1091 CONFIG_NATSEMI
1092 Support for National dp83815 chips.
1094 CONFIG_NS8382X
1095 Support for National dp8382[01] gigabit chips.
1097 - NETWORK Support (other):
1099 CONFIG_DRIVER_AT91EMAC
1100 Support for AT91RM9200 EMAC.
1102 CONFIG_RMII
1103 Define this to use reduced MII inteface
1105 CONFIG_DRIVER_AT91EMAC_QUIET
1106 If this defined, the driver is quiet.
1107 The driver doen't show link status messages.
1109 CONFIG_CALXEDA_XGMAC
1110 Support for the Calxeda XGMAC device
1112 CONFIG_LAN91C96
1113 Support for SMSC's LAN91C96 chips.
1115 CONFIG_LAN91C96_BASE
1116 Define this to hold the physical address
1117 of the LAN91C96's I/O space
1119 CONFIG_LAN91C96_USE_32_BIT
1120 Define this to enable 32 bit addressing
1122 CONFIG_SMC91111
1123 Support for SMSC's LAN91C111 chip
1125 CONFIG_SMC91111_BASE
1126 Define this to hold the physical address
1127 of the device (I/O space)
1129 CONFIG_SMC_USE_32_BIT
1130 Define this if data bus is 32 bits
1132 CONFIG_SMC_USE_IOFUNCS
1133 Define this to use i/o functions instead of macros
1134 (some hardware wont work with macros)
1136 CONFIG_DRIVER_TI_EMAC
1137 Support for davinci emac
1139 CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
1140 Define this if you have more then 3 PHYs.
1142 CONFIG_FTGMAC100
1143 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
1145 CONFIG_FTGMAC100_EGIGA
1146 Define this to use GE link update with gigabit PHY.
1147 Define this if FTGMAC100 is connected to gigabit PHY.
1148 If your system has 10/100 PHY only, it might not occur
1149 wrong behavior. Because PHY usually return timeout or
1150 useless data when polling gigabit status and gigabit
1151 control registers. This behavior won't affect the
1152 correctnessof 10/100 link speed update.
1154 CONFIG_SMC911X
1155 Support for SMSC's LAN911x and LAN921x chips
1157 CONFIG_SMC911X_BASE
1158 Define this to hold the physical address
1159 of the device (I/O space)
1161 CONFIG_SMC911X_32_BIT
1162 Define this if data bus is 32 bits
1164 CONFIG_SMC911X_16_BIT
1165 Define this if data bus is 16 bits. If your processor
1166 automatically converts one 32 bit word to two 16 bit
1167 words you may also try CONFIG_SMC911X_32_BIT.
1169 CONFIG_SH_ETHER
1170 Support for Renesas on-chip Ethernet controller
1172 CONFIG_SH_ETHER_USE_PORT
1173 Define the number of ports to be used
1175 CONFIG_SH_ETHER_PHY_ADDR
1176 Define the ETH PHY's address
1178 CONFIG_SH_ETHER_CACHE_WRITEBACK
1179 If this option is set, the driver enables cache flush.
1181 - TPM Support:
1182 CONFIG_GENERIC_LPC_TPM
1183 Support for generic parallel port TPM devices. Only one device
1184 per system is supported at this time.
1186 CONFIG_TPM_TIS_BASE_ADDRESS
1187 Base address where the generic TPM device is mapped
1188 to. Contemporary x86 systems usually map it at
1189 0xfed40000.
1191 - USB Support:
1192 At the moment only the UHCI host controller is
1193 supported (PIP405, MIP405, MPC5200); define
1194 CONFIG_USB_UHCI to enable it.
1195 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
1196 and define CONFIG_USB_STORAGE to enable the USB
1197 storage devices.
1198 Note:
1199 Supported are USB Keyboards and USB Floppy drives
1200 (TEAC FD-05PUB).
1201 MPC5200 USB requires additional defines:
1202 CONFIG_USB_CLOCK
1203 for 528 MHz Clock: 0x0001bbbb
1204 CONFIG_PSC3_USB
1205 for USB on PSC3
1206 CONFIG_USB_CONFIG
1207 for differential drivers: 0x00001000
1208 for single ended drivers: 0x00005000
1209 for differential drivers on PSC3: 0x00000100
1210 for single ended drivers on PSC3: 0x00004100
1211 CONFIG_SYS_USB_EVENT_POLL
1212 May be defined to allow interrupt polling
1213 instead of using asynchronous interrupts
1215 CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
1216 txfilltuning field in the EHCI controller on reset.
1218 - USB Device:
1219 Define the below if you wish to use the USB console.
1220 Once firmware is rebuilt from a serial console issue the
1221 command "setenv stdin usbtty; setenv stdout usbtty" and
1222 attach your USB cable. The Unix command "dmesg" should print
1223 it has found a new device. The environment variable usbtty
1224 can be set to gserial or cdc_acm to enable your device to
1225 appear to a USB host as a Linux gserial device or a
1226 Common Device Class Abstract Control Model serial device.
1227 If you select usbtty = gserial you should be able to enumerate
1228 a Linux host by
1229 # modprobe usbserial vendor=0xVendorID product=0xProductID
1230 else if using cdc_acm, simply setting the environment
1231 variable usbtty to be cdc_acm should suffice. The following
1232 might be defined in YourBoardName.h
1234 CONFIG_USB_DEVICE
1235 Define this to build a UDC device
1237 CONFIG_USB_TTY
1238 Define this to have a tty type of device available to
1239 talk to the UDC device
1241 CONFIG_USBD_HS
1242 Define this to enable the high speed support for usb
1243 device and usbtty. If this feature is enabled, a routine
1244 int is_usbd_high_speed(void)
1245 also needs to be defined by the driver to dynamically poll
1246 whether the enumeration has succeded at high speed or full
1247 speed.
1249 CONFIG_SYS_CONSOLE_IS_IN_ENV
1250 Define this if you want stdin, stdout &/or stderr to
1251 be set to usbtty.
1253 mpc8xx:
1254 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
1255 Derive USB clock from external clock "blah"
1256 - CONFIG_SYS_USB_EXTC_CLK 0x02
1258 CONFIG_SYS_USB_BRG_CLK 0xBLAH
1259 Derive USB clock from brgclk
1260 - CONFIG_SYS_USB_BRG_CLK 0x04
1262 If you have a USB-IF assigned VendorID then you may wish to
1263 define your own vendor specific values either in BoardName.h
1264 or directly in usbd_vendor_info.h. If you don't define
1265 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
1266 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
1267 should pretend to be a Linux device to it's target host.
1269 CONFIG_USBD_MANUFACTURER
1270 Define this string as the name of your company for
1271 - CONFIG_USBD_MANUFACTURER "my company"
1273 CONFIG_USBD_PRODUCT_NAME
1274 Define this string as the name of your product
1275 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1277 CONFIG_USBD_VENDORID
1278 Define this as your assigned Vendor ID from the USB
1279 Implementors Forum. This *must* be a genuine Vendor ID
1280 to avoid polluting the USB namespace.
1281 - CONFIG_USBD_VENDORID 0xFFFF
1283 CONFIG_USBD_PRODUCTID
1284 Define this as the unique Product ID
1285 for your device
1286 - CONFIG_USBD_PRODUCTID 0xFFFF
1288 - ULPI Layer Support:
1289 The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
1290 the generic ULPI layer. The generic layer accesses the ULPI PHY
1291 via the platform viewport, so you need both the genric layer and
1292 the viewport enabled. Currently only Chipidea/ARC based
1293 viewport is supported.
1294 To enable the ULPI layer support, define CONFIG_USB_ULPI and
1295 CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1296 If your ULPI phy needs a different reference clock than the
1297 standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
1298 the appropriate value in Hz.
1300 - MMC Support:
1301 The MMC controller on the Intel PXA is supported. To
1302 enable this define CONFIG_MMC. The MMC can be
1303 accessed from the boot prompt by mapping the device
1304 to physical memory similar to flash. Command line is
1305 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1306 the FAT fs. This is enabled with CONFIG_CMD_FAT.
1308 CONFIG_SH_MMCIF
1309 Support for Renesas on-chip MMCIF controller
1311 CONFIG_SH_MMCIF_ADDR
1312 Define the base address of MMCIF registers
1314 CONFIG_SH_MMCIF_CLK
1315 Define the clock frequency for MMCIF
1317 - Journaling Flash filesystem support:
1318 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1319 CONFIG_JFFS2_NAND_DEV
1320 Define these for a default partition on a NAND device
1322 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1323 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1324 Define these for a default partition on a NOR device
1326 CONFIG_SYS_JFFS_CUSTOM_PART
1327 Define this to create an own partition. You have to provide a
1328 function struct part_info* jffs2_part_info(int part_num)
1330 If you define only one JFFS2 partition you may also want to
1331 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1332 to disable the command chpart. This is the default when you
1333 have not defined a custom partition
1335 - FAT(File Allocation Table) filesystem write function support:
1336 CONFIG_FAT_WRITE
1338 Define this to enable support for saving memory data as a
1339 file in FAT formatted partition.
1341 This will also enable the command "fatwrite" enabling the
1342 user to write files to FAT.
1344 CBFS (Coreboot Filesystem) support
1345 CONFIG_CMD_CBFS
1347 Define this to enable support for reading from a Coreboot
1348 filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
1349 and cbfsload.
1351 - Keyboard Support:
1352 CONFIG_ISA_KEYBOARD
1354 Define this to enable standard (PC-Style) keyboard
1355 support
1357 CONFIG_I8042_KBD
1358 Standard PC keyboard driver with US (is default) and
1359 GERMAN key layout (switch via environment 'keymap=de') support.
1360 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1361 for cfb_console. Supports cursor blinking.
1363 - Video support:
1364 CONFIG_VIDEO
1366 Define this to enable video support (for output to
1367 video).
1369 CONFIG_VIDEO_CT69000
1371 Enable Chips & Technologies 69000 Video chip
1373 CONFIG_VIDEO_SMI_LYNXEM
1374 Enable Silicon Motion SMI 712/710/810 Video chip. The
1375 video output is selected via environment 'videoout'
1376 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1377 assumed.
1379 For the CT69000 and SMI_LYNXEM drivers, videomode is
1380 selected via environment 'videomode'. Two different ways
1381 are possible:
1382 - "videomode=num" 'num' is a standard LiLo mode numbers.
1383 Following standard modes are supported (* is default):
1385 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1386 -------------+---------------------------------------------
1387 8 bits | 0x301* 0x303 0x305 0x161 0x307
1388 15 bits | 0x310 0x313 0x316 0x162 0x319
1389 16 bits | 0x311 0x314 0x317 0x163 0x31A
1390 24 bits | 0x312 0x315 0x318 ? 0x31B
1391 -------------+---------------------------------------------
1392 (i.e. setenv videomode 317; saveenv; reset;)
1394 - "videomode=bootargs" all the video parameters are parsed
1395 from the bootargs. (See drivers/video/videomodes.c)
1398 CONFIG_VIDEO_SED13806
1399 Enable Epson SED13806 driver. This driver supports 8bpp
1400 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1401 or CONFIG_VIDEO_SED13806_16BPP
1403 CONFIG_FSL_DIU_FB
1404 Enable the Freescale DIU video driver. Reference boards for
1405 SOCs that have a DIU should define this macro to enable DIU
1406 support, and should also define these other macros:
1408 CONFIG_SYS_DIU_ADDR
1409 CONFIG_VIDEO
1410 CONFIG_CMD_BMP
1411 CONFIG_CFB_CONSOLE
1412 CONFIG_VIDEO_SW_CURSOR
1413 CONFIG_VGA_AS_SINGLE_DEVICE
1414 CONFIG_VIDEO_LOGO
1415 CONFIG_VIDEO_BMP_LOGO
1417 The DIU driver will look for the 'video-mode' environment
1418 variable, and if defined, enable the DIU as a console during
1419 boot. See the documentation file README.video for a
1420 description of this variable.
1422 CONFIG_VIDEO_VGA
1424 Enable the VGA video / BIOS for x86. The alternative if you
1425 are using coreboot is to use the coreboot frame buffer
1426 driver.
1429 - Keyboard Support:
1430 CONFIG_KEYBOARD
1432 Define this to enable a custom keyboard support.
1433 This simply calls drv_keyboard_init() which must be
1434 defined in your board-specific files.
1435 The only board using this so far is RBC823.
1437 - LCD Support: CONFIG_LCD
1439 Define this to enable LCD support (for output to LCD
1440 display); also select one of the supported displays
1441 by defining one of these:
1443 CONFIG_ATMEL_LCD:
1445 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1447 CONFIG_NEC_NL6448AC33:
1449 NEC NL6448AC33-18. Active, color, single scan.
1451 CONFIG_NEC_NL6448BC20
1453 NEC NL6448BC20-08. 6.5", 640x480.
1454 Active, color, single scan.
1456 CONFIG_NEC_NL6448BC33_54
1458 NEC NL6448BC33-54. 10.4", 640x480.
1459 Active, color, single scan.
1461 CONFIG_SHARP_16x9
1463 Sharp 320x240. Active, color, single scan.
1464 It isn't 16x9, and I am not sure what it is.
1466 CONFIG_SHARP_LQ64D341
1468 Sharp LQ64D341 display, 640x480.
1469 Active, color, single scan.
1471 CONFIG_HLD1045
1473 HLD1045 display, 640x480.
1474 Active, color, single scan.
1476 CONFIG_OPTREX_BW
1478 Optrex CBL50840-2 NF-FW 99 22 M5
1479 or
1480 Hitachi LMG6912RPFC-00T
1481 or
1482 Hitachi SP14Q002
1484 320x240. Black & white.
1486 Normally display is black on white background; define
1487 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1489 CONFIG_LCD_ALIGNMENT
1491 Normally the LCD is page-aligned (tyically 4KB). If this is
1492 defined then the LCD will be aligned to this value instead.
1493 For ARM it is sometimes useful to use MMU_SECTION_SIZE
1494 here, since it is cheaper to change data cache settings on
1495 a per-section basis.
1497 CONFIG_CONSOLE_SCROLL_LINES
1499 When the console need to be scrolled, this is the number of
1500 lines to scroll by. It defaults to 1. Increasing this makes
1501 the console jump but can help speed up operation when scrolling
1502 is slow.
1504 CONFIG_LCD_BMP_RLE8
1506 Support drawing of RLE8-compressed bitmaps on the LCD.
1508 CONFIG_I2C_EDID
1510 Enables an 'i2c edid' command which can read EDID
1511 information over I2C from an attached LCD display.
1513 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1515 If this option is set, the environment is checked for
1516 a variable "splashimage". If found, the usual display
1517 of logo, copyright and system information on the LCD
1518 is suppressed and the BMP image at the address
1519 specified in "splashimage" is loaded instead. The
1520 console is redirected to the "nulldev", too. This
1521 allows for a "silent" boot where a splash screen is
1522 loaded very quickly after power-on.
1524 CONFIG_SPLASH_SCREEN_ALIGN
1526 If this option is set the splash image can be freely positioned
1527 on the screen. Environment variable "splashpos" specifies the
1528 position as "x,y". If a positive number is given it is used as
1529 number of pixel from left/top. If a negative number is given it
1530 is used as number of pixel from right/bottom. You can also
1531 specify 'm' for centering the image.
1533 Example:
1534 setenv splashpos m,m
1535 => image at center of screen
1537 setenv splashpos 30,20
1538 => image at x = 30 and y = 20
1540 setenv splashpos -10,m
1541 => vertically centered image
1542 at x = dspWidth - bmpWidth - 9
1544 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1546 If this option is set, additionally to standard BMP
1547 images, gzipped BMP images can be displayed via the
1548 splashscreen support or the bmp command.
1550 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
1552 If this option is set, 8-bit RLE compressed BMP images
1553 can be displayed via the splashscreen support or the
1554 bmp command.
1556 - Do compresssing for memory range:
1557 CONFIG_CMD_ZIP
1559 If this option is set, it would use zlib deflate method
1560 to compress the specified memory at its best effort.
1562 - Compression support:
1563 CONFIG_BZIP2
1565 If this option is set, support for bzip2 compressed
1566 images is included. If not, only uncompressed and gzip
1567 compressed images are supported.
1569 NOTE: the bzip2 algorithm requires a lot of RAM, so
1570 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1571 be at least 4MB.
1573 CONFIG_LZMA
1575 If this option is set, support for lzma compressed
1576 images is included.
1578 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1579 requires an amount of dynamic memory that is given by the
1580 formula:
1582 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1584 Where lc and lp stand for, respectively, Literal context bits
1585 and Literal pos bits.
1587 This value is upper-bounded by 14MB in the worst case. Anyway,
1588 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1589 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1590 a very small buffer.
1592 Use the lzmainfo tool to determinate the lc and lp values and
1593 then calculate the amount of needed dynamic memory (ensuring
1594 the appropriate CONFIG_SYS_MALLOC_LEN value).
1596 - MII/PHY support:
1597 CONFIG_PHY_ADDR
1599 The address of PHY on MII bus.
1601 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1603 The clock frequency of the MII bus
1605 CONFIG_PHY_GIGE
1607 If this option is set, support for speed/duplex
1608 detection of gigabit PHY is included.
1610 CONFIG_PHY_RESET_DELAY
1612 Some PHY like Intel LXT971A need extra delay after
1613 reset before any MII register access is possible.
1614 For such PHY, set this option to the usec delay
1615 required. (minimum 300usec for LXT971A)
1617 CONFIG_PHY_CMD_DELAY (ppc4xx)
1619 Some PHY like Intel LXT971A need extra delay after
1620 command issued before MII status register can be read
1622 - Ethernet address:
1623 CONFIG_ETHADDR
1624 CONFIG_ETH1ADDR
1625 CONFIG_ETH2ADDR
1626 CONFIG_ETH3ADDR
1627 CONFIG_ETH4ADDR
1628 CONFIG_ETH5ADDR
1630 Define a default value for Ethernet address to use
1631 for the respective Ethernet interface, in case this
1632 is not determined automatically.
1634 - IP address:
1635 CONFIG_IPADDR
1637 Define a default value for the IP address to use for
1638 the default Ethernet interface, in case this is not
1639 determined through e.g. bootp.
1640 (Environment variable "ipaddr")
1642 - Server IP address:
1643 CONFIG_SERVERIP
1645 Defines a default value for the IP address of a TFTP
1646 server to contact when using the "tftboot" command.
1647 (Environment variable "serverip")
1649 CONFIG_KEEP_SERVERADDR
1651 Keeps the server's MAC address, in the env 'serveraddr'
1652 for passing to bootargs (like Linux's netconsole option)
1654 - Gateway IP address:
1655 CONFIG_GATEWAYIP
1657 Defines a default value for the IP address of the
1658 default router where packets to other networks are
1659 sent to.
1660 (Environment variable "gatewayip")
1662 - Subnet mask:
1663 CONFIG_NETMASK
1665 Defines a default value for the subnet mask (or
1666 routing prefix) which is used to determine if an IP
1667 address belongs to the local subnet or needs to be
1668 forwarded through a router.
1669 (Environment variable "netmask")
1671 - Multicast TFTP Mode:
1672 CONFIG_MCAST_TFTP
1674 Defines whether you want to support multicast TFTP as per
1675 rfc-2090; for example to work with atftp. Lets lots of targets
1676 tftp down the same boot image concurrently. Note: the Ethernet
1677 driver in use must provide a function: mcast() to join/leave a
1678 multicast group.
1680 - BOOTP Recovery Mode:
1681 CONFIG_BOOTP_RANDOM_DELAY
1683 If you have many targets in a network that try to
1684 boot using BOOTP, you may want to avoid that all
1685 systems send out BOOTP requests at precisely the same
1686 moment (which would happen for instance at recovery
1687 from a power failure, when all systems will try to
1688 boot, thus flooding the BOOTP server. Defining
1689 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1690 inserted before sending out BOOTP requests. The
1691 following delays are inserted then:
1693 1st BOOTP request: delay 0 ... 1 sec
1694 2nd BOOTP request: delay 0 ... 2 sec
1695 3rd BOOTP request: delay 0 ... 4 sec
1696 4th and following
1697 BOOTP requests: delay 0 ... 8 sec
1699 - DHCP Advanced Options:
1700 You can fine tune the DHCP functionality by defining
1701 CONFIG_BOOTP_* symbols:
1703 CONFIG_BOOTP_SUBNETMASK
1704 CONFIG_BOOTP_GATEWAY
1705 CONFIG_BOOTP_HOSTNAME
1706 CONFIG_BOOTP_NISDOMAIN
1707 CONFIG_BOOTP_BOOTPATH
1708 CONFIG_BOOTP_BOOTFILESIZE
1709 CONFIG_BOOTP_DNS
1710 CONFIG_BOOTP_DNS2
1711 CONFIG_BOOTP_SEND_HOSTNAME
1712 CONFIG_BOOTP_NTPSERVER
1713 CONFIG_BOOTP_TIMEOFFSET
1714 CONFIG_BOOTP_VENDOREX
1715 CONFIG_BOOTP_MAY_FAIL
1717 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1718 environment variable, not the BOOTP server.
1720 CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
1721 after the configured retry count, the call will fail
1722 instead of starting over. This can be used to fail over
1723 to Link-local IP address configuration if the DHCP server
1724 is not available.
1726 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1727 serverip from a DHCP server, it is possible that more
1728 than one DNS serverip is offered to the client.
1729 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1730 serverip will be stored in the additional environment
1731 variable "dnsip2". The first DNS serverip is always
1732 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1733 is defined.
1735 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1736 to do a dynamic update of a DNS server. To do this, they
1737 need the hostname of the DHCP requester.
1738 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1739 of the "hostname" environment variable is passed as
1740 option 12 to the DHCP server.
1742 CONFIG_BOOTP_DHCP_REQUEST_DELAY
1744 A 32bit value in microseconds for a delay between
1745 receiving a "DHCP Offer" and sending the "DHCP Request".
1746 This fixes a problem with certain DHCP servers that don't
1747 respond 100% of the time to a "DHCP request". E.g. On an
1748 AT91RM9200 processor running at 180MHz, this delay needed
1749 to be *at least* 15,000 usec before a Windows Server 2003
1750 DHCP server would reply 100% of the time. I recommend at
1751 least 50,000 usec to be safe. The alternative is to hope
1752 that one of the retries will be successful but note that
1753 the DHCP timeout and retry process takes a longer than
1754 this delay.
1756 - Link-local IP address negotiation:
1757 Negotiate with other link-local clients on the local network
1758 for an address that doesn't require explicit configuration.
1759 This is especially useful if a DHCP server cannot be guaranteed
1760 to exist in all environments that the device must operate.
1762 See doc/README.link-local for more information.
1764 - CDP Options:
1765 CONFIG_CDP_DEVICE_ID
1767 The device id used in CDP trigger frames.
1769 CONFIG_CDP_DEVICE_ID_PREFIX
1771 A two character string which is prefixed to the MAC address
1772 of the device.
1774 CONFIG_CDP_PORT_ID
1776 A printf format string which contains the ascii name of
1777 the port. Normally is set to "eth%d" which sets
1778 eth0 for the first Ethernet, eth1 for the second etc.
1780 CONFIG_CDP_CAPABILITIES
1782 A 32bit integer which indicates the device capabilities;
1783 0x00000010 for a normal host which does not forwards.
1785 CONFIG_CDP_VERSION
1787 An ascii string containing the version of the software.
1789 CONFIG_CDP_PLATFORM
1791 An ascii string containing the name of the platform.
1793 CONFIG_CDP_TRIGGER
1795 A 32bit integer sent on the trigger.
1797 CONFIG_CDP_POWER_CONSUMPTION
1799 A 16bit integer containing the power consumption of the
1800 device in .1 of milliwatts.
1802 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1804 A byte containing the id of the VLAN.
1806 - Status LED: CONFIG_STATUS_LED
1808 Several configurations allow to display the current
1809 status using a LED. For instance, the LED will blink
1810 fast while running U-Boot code, stop blinking as
1811 soon as a reply to a BOOTP request was received, and
1812 start blinking slow once the Linux kernel is running
1813 (supported by a status LED driver in the Linux
1814 kernel). Defining CONFIG_STATUS_LED enables this
1815 feature in U-Boot.
1817 - CAN Support: CONFIG_CAN_DRIVER
1819 Defining CONFIG_CAN_DRIVER enables CAN driver support
1820 on those systems that support this (optional)
1821 feature, like the TQM8xxL modules.
1823 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1825 These enable I2C serial bus commands. Defining either of
1826 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1827 include the appropriate I2C driver for the selected CPU.
1829 This will allow you to use i2c commands at the u-boot
1830 command line (as long as you set CONFIG_CMD_I2C in
1831 CONFIG_COMMANDS) and communicate with i2c based realtime
1832 clock chips. See common/cmd_i2c.c for a description of the
1833 command line interface.
1835 CONFIG_HARD_I2C selects a hardware I2C controller.
1837 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1838 bit-banging) driver instead of CPM or similar hardware
1839 support for I2C.
1841 There are several other quantities that must also be
1842 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1844 In both cases you will need to define CONFIG_SYS_I2C_SPEED
1845 to be the frequency (in Hz) at which you wish your i2c bus
1846 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
1847 the CPU's i2c node address).
1849 Now, the u-boot i2c code for the mpc8xx
1850 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
1851 and so its address should therefore be cleared to 0 (See,
1852 eg, MPC823e User's Manual p.16-473). So, set
1853 CONFIG_SYS_I2C_SLAVE to 0.
1855 CONFIG_SYS_I2C_INIT_MPC5XXX
1857 When a board is reset during an i2c bus transfer
1858 chips might think that the current transfer is still
1859 in progress. Reset the slave devices by sending start
1860 commands until the slave device responds.
1862 That's all that's required for CONFIG_HARD_I2C.
1864 If you use the software i2c interface (CONFIG_SOFT_I2C)
1865 then the following macros need to be defined (examples are
1866 from include/configs/lwmon.h):
1868 I2C_INIT
1870 (Optional). Any commands necessary to enable the I2C
1871 controller or configure ports.
1873 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1875 I2C_PORT
1877 (Only for MPC8260 CPU). The I/O port to use (the code
1878 assumes both bits are on the same port). Valid values
1879 are 0..3 for ports A..D.
1881 I2C_ACTIVE
1883 The code necessary to make the I2C data line active
1884 (driven). If the data line is open collector, this
1885 define can be null.
1887 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1889 I2C_TRISTATE
1891 The code necessary to make the I2C data line tri-stated
1892 (inactive). If the data line is open collector, this
1893 define can be null.
1895 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1897 I2C_READ
1899 Code that returns TRUE if the I2C data line is high,
1900 FALSE if it is low.
1902 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1904 I2C_SDA(bit)
1906 If <bit> is TRUE, sets the I2C data line high. If it
1907 is FALSE, it clears it (low).
1909 eg: #define I2C_SDA(bit) \
1910 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1911 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1913 I2C_SCL(bit)
1915 If <bit> is TRUE, sets the I2C clock line high. If it
1916 is FALSE, it clears it (low).
1918 eg: #define I2C_SCL(bit) \
1919 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1920 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1922 I2C_DELAY
1924 This delay is invoked four times per clock cycle so this
1925 controls the rate of data transfer. The data rate thus
1926 is 1 / (I2C_DELAY * 4). Often defined to be something
1927 like:
1929 #define I2C_DELAY udelay(2)
1931 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
1933 If your arch supports the generic GPIO framework (asm/gpio.h),
1934 then you may alternatively define the two GPIOs that are to be
1935 used as SCL / SDA. Any of the previous I2C_xxx macros will
1936 have GPIO-based defaults assigned to them as appropriate.
1938 You should define these to the GPIO value as given directly to
1939 the generic GPIO functions.
1941 CONFIG_SYS_I2C_INIT_BOARD
1943 When a board is reset during an i2c bus transfer
1944 chips might think that the current transfer is still
1945 in progress. On some boards it is possible to access
1946 the i2c SCLK line directly, either by using the
1947 processor pin as a GPIO or by having a second pin
1948 connected to the bus. If this option is defined a
1949 custom i2c_init_board() routine in boards/xxx/board.c
1950 is run early in the boot sequence.
1952 CONFIG_SYS_I2C_BOARD_LATE_INIT
1954 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
1955 defined a custom i2c_board_late_init() routine in
1956 boards/xxx/board.c is run AFTER the operations in i2c_init()
1957 is completed. This callpoint can be used to unreset i2c bus
1958 using CPU i2c controller register accesses for CPUs whose i2c
1959 controller provide such a method. It is called at the end of
1960 i2c_init() to allow i2c_init operations to setup the i2c bus
1961 controller on the CPU (e.g. setting bus speed & slave address).
1963 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1965 This option enables configuration of bi_iic_fast[] flags
1966 in u-boot bd_info structure based on u-boot environment
1967 variable "i2cfast". (see also i2cfast)
1969 CONFIG_I2C_MULTI_BUS
1971 This option allows the use of multiple I2C buses, each of which
1972 must have a controller. At any point in time, only one bus is
1973 active. To switch to a different bus, use the 'i2c dev' command.
1974 Note that bus numbering is zero-based.
1976 CONFIG_SYS_I2C_NOPROBES
1978 This option specifies a list of I2C devices that will be skipped
1979 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
1980 is set, specify a list of bus-device pairs. Otherwise, specify
1981 a 1D array of device addresses
1983 e.g.
1984 #undef CONFIG_I2C_MULTI_BUS
1985 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
1987 will skip addresses 0x50 and 0x68 on a board with one I2C bus
1989 #define CONFIG_I2C_MULTI_BUS
1990 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
1992 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
1994 CONFIG_SYS_SPD_BUS_NUM
1996 If defined, then this indicates the I2C bus number for DDR SPD.
1997 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
1999 CONFIG_SYS_RTC_BUS_NUM
2001 If defined, then this indicates the I2C bus number for the RTC.
2002 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
2004 CONFIG_SYS_DTT_BUS_NUM
2006 If defined, then this indicates the I2C bus number for the DTT.
2007 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
2009 CONFIG_SYS_I2C_DTT_ADDR:
2011 If defined, specifies the I2C address of the DTT device.
2012 If not defined, then U-Boot uses predefined value for
2013 specified DTT device.
2015 CONFIG_FSL_I2C
2017 Define this option if you want to use Freescale's I2C driver in
2018 drivers/i2c/fsl_i2c.c.
2020 CONFIG_I2C_MUX
2022 Define this option if you have I2C devices reached over 1 .. n
2023 I2C Muxes like the pca9544a. This option addes a new I2C
2024 Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a
2025 new I2C Bus to the existing I2C Busses. If you select the
2026 new Bus with "i2c dev", u-bbot sends first the commandos for
2027 the muxes to activate this new "bus".
2029 CONFIG_I2C_MULTI_BUS must be also defined, to use this
2030 feature!
2032 Example:
2033 Adding a new I2C Bus reached over 2 pca9544a muxes
2034 The First mux with address 70 and channel 6
2035 The Second mux with address 71 and channel 4
2037 => i2c bus pca9544a:70:6:pca9544a:71:4
2039 Use the "i2c bus" command without parameter, to get a list
2040 of I2C Busses with muxes:
2042 => i2c bus
2043 Busses reached over muxes:
2044 Bus ID: 2
2045 reached over Mux(es):
2046 pca9544a@70 ch: 4
2047 Bus ID: 3
2048 reached over Mux(es):
2049 pca9544a@70 ch: 6
2050 pca9544a@71 ch: 4
2051 =>
2053 If you now switch to the new I2C Bus 3 with "i2c dev 3"
2054 u-boot first sends the command to the mux@70 to enable
2055 channel 6, and then the command to the mux@71 to enable
2056 the channel 4.
2058 After that, you can use the "normal" i2c commands as
2059 usual to communicate with your I2C devices behind
2060 the 2 muxes.
2062 This option is actually implemented for the bitbanging
2063 algorithm in common/soft_i2c.c and for the Hardware I2C
2064 Bus on the MPC8260. But it should be not so difficult
2065 to add this option to other architectures.
2067 CONFIG_SOFT_I2C_READ_REPEATED_START
2069 defining this will force the i2c_read() function in
2070 the soft_i2c driver to perform an I2C repeated start
2071 between writing the address pointer and reading the
2072 data. If this define is omitted the default behaviour
2073 of doing a stop-start sequence will be used. Most I2C
2074 devices can use either method, but some require one or
2075 the other.
2077 - SPI Support: CONFIG_SPI
2079 Enables SPI driver (so far only tested with
2080 SPI EEPROM, also an instance works with Crystal A/D and
2081 D/As on the SACSng board)
2083 CONFIG_SH_SPI
2085 Enables the driver for SPI controller on SuperH. Currently
2086 only SH7757 is supported.
2088 CONFIG_SPI_X
2090 Enables extended (16-bit) SPI EEPROM addressing.
2091 (symmetrical to CONFIG_I2C_X)
2093 CONFIG_SOFT_SPI
2095 Enables a software (bit-bang) SPI driver rather than
2096 using hardware support. This is a general purpose
2097 driver that only requires three general I/O port pins
2098 (two outputs, one input) to function. If this is
2099 defined, the board configuration must define several
2100 SPI configuration items (port pins to use, etc). For
2101 an example, see include/configs/sacsng.h.
2103 CONFIG_HARD_SPI
2105 Enables a hardware SPI driver for general-purpose reads
2106 and writes. As with CONFIG_SOFT_SPI, the board configuration
2107 must define a list of chip-select function pointers.
2108 Currently supported on some MPC8xxx processors. For an
2109 example, see include/configs/mpc8349emds.h.
2111 CONFIG_MXC_SPI
2113 Enables the driver for the SPI controllers on i.MX and MXC
2114 SoCs. Currently i.MX31/35/51 are supported.
2116 - FPGA Support: CONFIG_FPGA
2118 Enables FPGA subsystem.
2120 CONFIG_FPGA_<vendor>
2122 Enables support for specific chip vendors.
2123 (ALTERA, XILINX)
2125 CONFIG_FPGA_<family>
2127 Enables support for FPGA family.
2128 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
2130 CONFIG_FPGA_COUNT
2132 Specify the number of FPGA devices to support.
2134 CONFIG_SYS_FPGA_PROG_FEEDBACK
2136 Enable printing of hash marks during FPGA configuration.
2138 CONFIG_SYS_FPGA_CHECK_BUSY
2140 Enable checks on FPGA configuration interface busy
2141 status by the configuration function. This option
2142 will require a board or device specific function to
2143 be written.
2145 CONFIG_FPGA_DELAY
2147 If defined, a function that provides delays in the FPGA
2148 configuration driver.
2150 CONFIG_SYS_FPGA_CHECK_CTRLC
2151 Allow Control-C to interrupt FPGA configuration
2153 CONFIG_SYS_FPGA_CHECK_ERROR
2155 Check for configuration errors during FPGA bitfile
2156 loading. For example, abort during Virtex II
2157 configuration if the INIT_B line goes low (which
2158 indicated a CRC error).
2160 CONFIG_SYS_FPGA_WAIT_INIT
2162 Maximum time to wait for the INIT_B line to deassert
2163 after PROB_B has been deasserted during a Virtex II
2164 FPGA configuration sequence. The default time is 500
2165 ms.
2167 CONFIG_SYS_FPGA_WAIT_BUSY
2169 Maximum time to wait for BUSY to deassert during
2170 Virtex II FPGA configuration. The default is 5 ms.
2172 CONFIG_SYS_FPGA_WAIT_CONFIG
2174 Time to wait after FPGA configuration. The default is
2175 200 ms.
2177 - Configuration Management:
2178 CONFIG_IDENT_STRING
2180 If defined, this string will be added to the U-Boot
2181 version information (U_BOOT_VERSION)
2183 - Vendor Parameter Protection:
2185 U-Boot considers the values of the environment
2186 variables "serial#" (Board Serial Number) and
2187 "ethaddr" (Ethernet Address) to be parameters that
2188 are set once by the board vendor / manufacturer, and
2189 protects these variables from casual modification by
2190 the user. Once set, these variables are read-only,
2191 and write or delete attempts are rejected. You can
2192 change this behaviour:
2194 If CONFIG_ENV_OVERWRITE is #defined in your config
2195 file, the write protection for vendor parameters is
2196 completely disabled. Anybody can change or delete
2197 these parameters.
2199 Alternatively, if you #define _both_ CONFIG_ETHADDR
2200 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
2201 Ethernet address is installed in the environment,
2202 which can be changed exactly ONCE by the user. [The
2203 serial# is unaffected by this, i. e. it remains
2204 read-only.]
2206 The same can be accomplished in a more flexible way
2207 for any variable by configuring the type of access
2208 to allow for those variables in the ".flags" variable
2209 or define CONFIG_ENV_FLAGS_LIST_STATIC.
2211 - Protected RAM:
2212 CONFIG_PRAM
2214 Define this variable to enable the reservation of
2215 "protected RAM", i. e. RAM which is not overwritten
2216 by U-Boot. Define CONFIG_PRAM to hold the number of
2217 kB you want to reserve for pRAM. You can overwrite
2218 this default value by defining an environment
2219 variable "pram" to the number of kB you want to
2220 reserve. Note that the board info structure will
2221 still show the full amount of RAM. If pRAM is
2222 reserved, a new environment variable "mem" will
2223 automatically be defined to hold the amount of
2224 remaining RAM in a form that can be passed as boot
2225 argument to Linux, for instance like that:
2227 setenv bootargs ... mem=\${mem}
2228 saveenv
2230 This way you can tell Linux not to use this memory,
2231 either, which results in a memory region that will
2232 not be affected by reboots.
2234 *WARNING* If your board configuration uses automatic
2235 detection of the RAM size, you must make sure that
2236 this memory test is non-destructive. So far, the
2237 following board configurations are known to be
2238 "pRAM-clean":
2240 IVMS8, IVML24, SPD8xx, TQM8xxL,
2241 HERMES, IP860, RPXlite, LWMON,
2242 FLAGADM, TQM8260
2244 - Access to physical memory region (> 4GB)
2245 Some basic support is provided for operations on memory not
2246 normally accessible to U-Boot - e.g. some architectures
2247 support access to more than 4GB of memory on 32-bit
2248 machines using physical address extension or similar.
2249 Define CONFIG_PHYSMEM to access this basic support, which
2250 currently only supports clearing the memory.
2252 - Error Recovery:
2253 CONFIG_PANIC_HANG
2255 Define this variable to stop the system in case of a
2256 fatal error, so that you have to reset it manually.
2257 This is probably NOT a good idea for an embedded
2258 system where you want the system to reboot
2259 automatically as fast as possible, but it may be
2260 useful during development since you can try to debug
2261 the conditions that lead to the situation.
2263 CONFIG_NET_RETRY_COUNT
2265 This variable defines the number of retries for
2266 network operations like ARP, RARP, TFTP, or BOOTP
2267 before giving up the operation. If not defined, a
2268 default value of 5 is used.
2270 CONFIG_ARP_TIMEOUT
2272 Timeout waiting for an ARP reply in milliseconds.
2274 CONFIG_NFS_TIMEOUT
2276 Timeout in milliseconds used in NFS protocol.
2277 If you encounter "ERROR: Cannot umount" in nfs command,
2278 try longer timeout such as
2279 #define CONFIG_NFS_TIMEOUT 10000UL
2281 - Command Interpreter:
2282 CONFIG_AUTO_COMPLETE
2284 Enable auto completion of commands using TAB.
2286 Note that this feature has NOT been implemented yet
2287 for the "hush" shell.
2290 CONFIG_SYS_HUSH_PARSER
2292 Define this variable to enable the "hush" shell (from
2293 Busybox) as command line interpreter, thus enabling
2294 powerful command line syntax like
2295 if...then...else...fi conditionals or `&&' and '||'
2296 constructs ("shell scripts").
2298 If undefined, you get the old, much simpler behaviour
2299 with a somewhat smaller memory footprint.
2302 CONFIG_SYS_PROMPT_HUSH_PS2
2304 This defines the secondary prompt string, which is
2305 printed when the command interpreter needs more input
2306 to complete a command. Usually "> ".
2308 Note:
2310 In the current implementation, the local variables
2311 space and global environment variables space are
2312 separated. Local variables are those you define by
2313 simply typing `name=value'. To access a local
2314 variable later on, you have write `$name' or
2315 `${name}'; to execute the contents of a variable
2316 directly type `$name' at the command prompt.
2318 Global environment variables are those you use
2319 setenv/printenv to work with. To run a command stored
2320 in such a variable, you need to use the run command,
2321 and you must not use the '$' sign to access them.
2323 To store commands and special characters in a
2324 variable, please use double quotation marks
2325 surrounding the whole text of the variable, instead
2326 of the backslashes before semicolons and special
2327 symbols.
2329 - Commandline Editing and History:
2330 CONFIG_CMDLINE_EDITING
2332 Enable editing and History functions for interactive
2333 commandline input operations
2335 - Default Environment:
2336 CONFIG_EXTRA_ENV_SETTINGS
2338 Define this to contain any number of null terminated
2339 strings (variable = value pairs) that will be part of
2340 the default environment compiled into the boot image.
2342 For example, place something like this in your
2343 board's config file:
2345 #define CONFIG_EXTRA_ENV_SETTINGS \
2346 "myvar1=value1\0" \
2347 "myvar2=value2\0"
2349 Warning: This method is based on knowledge about the
2350 internal format how the environment is stored by the
2351 U-Boot code. This is NOT an official, exported
2352 interface! Although it is unlikely that this format
2353 will change soon, there is no guarantee either.
2354 You better know what you are doing here.
2356 Note: overly (ab)use of the default environment is
2357 discouraged. Make sure to check other ways to preset
2358 the environment like the "source" command or the
2359 boot command first.
2361 CONFIG_ENV_VARS_UBOOT_CONFIG
2363 Define this in order to add variables describing the
2364 U-Boot build configuration to the default environment.
2365 These will be named arch, cpu, board, vendor, and soc.
2367 Enabling this option will cause the following to be defined:
2369 - CONFIG_SYS_ARCH
2370 - CONFIG_SYS_CPU
2371 - CONFIG_SYS_BOARD
2372 - CONFIG_SYS_VENDOR
2373 - CONFIG_SYS_SOC
2375 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
2377 Define this in order to add variables describing certain
2378 run-time determined information about the hardware to the
2379 environment. These will be named board_name, board_rev.
2381 - DataFlash Support:
2382 CONFIG_HAS_DATAFLASH
2384 Defining this option enables DataFlash features and
2385 allows to read/write in Dataflash via the standard
2386 commands cp, md...
2388 - Serial Flash support
2389 CONFIG_CMD_SF
2391 Defining this option enables SPI flash commands
2392 'sf probe/read/write/erase/update'.
2394 Usage requires an initial 'probe' to define the serial
2395 flash parameters, followed by read/write/erase/update
2396 commands.
2398 The following defaults may be provided by the platform
2399 to handle the common case when only a single serial
2400 flash is present on the system.
2402 CONFIG_SF_DEFAULT_BUS Bus identifier
2403 CONFIG_SF_DEFAULT_CS Chip-select
2404 CONFIG_SF_DEFAULT_MODE (see include/spi.h)
2405 CONFIG_SF_DEFAULT_SPEED in Hz
2407 - SystemACE Support:
2408 CONFIG_SYSTEMACE
2410 Adding this option adds support for Xilinx SystemACE
2411 chips attached via some sort of local bus. The address
2412 of the chip must also be defined in the
2413 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
2415 #define CONFIG_SYSTEMACE
2416 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
2418 When SystemACE support is added, the "ace" device type
2419 becomes available to the fat commands, i.e. fatls.
2421 - TFTP Fixed UDP Port:
2422 CONFIG_TFTP_PORT
2424 If this is defined, the environment variable tftpsrcp
2425 is used to supply the TFTP UDP source port value.
2426 If tftpsrcp isn't defined, the normal pseudo-random port
2427 number generator is used.
2429 Also, the environment variable tftpdstp is used to supply
2430 the TFTP UDP destination port value. If tftpdstp isn't
2431 defined, the normal port 69 is used.
2433 The purpose for tftpsrcp is to allow a TFTP server to
2434 blindly start the TFTP transfer using the pre-configured
2435 target IP address and UDP port. This has the effect of
2436 "punching through" the (Windows XP) firewall, allowing
2437 the remainder of the TFTP transfer to proceed normally.
2438 A better solution is to properly configure the firewall,
2439 but sometimes that is not allowed.
2441 - Hashing support:
2442 CONFIG_CMD_HASH
2444 This enables a generic 'hash' command which can produce
2445 hashes / digests from a few algorithms (e.g. SHA1, SHA256).
2447 CONFIG_HASH_VERIFY
2449 Enable the hash verify command (hash -v). This adds to code
2450 size a little.
2452 CONFIG_SHA1 - support SHA1 hashing
2453 CONFIG_SHA256 - support SHA256 hashing
2455 Note: There is also a sha1sum command, which should perhaps
2456 be deprecated in favour of 'hash sha1'.
2458 - Show boot progress:
2459 CONFIG_SHOW_BOOT_PROGRESS
2461 Defining this option allows to add some board-
2462 specific code (calling a user-provided function
2463 "show_boot_progress(int)") that enables you to show
2464 the system's boot progress on some display (for
2465 example, some LED's) on your board. At the moment,
2466 the following checkpoints are implemented:
2468 - Detailed boot stage timing
2469 CONFIG_BOOTSTAGE
2470 Define this option to get detailed timing of each stage
2471 of the boot process.
2473 CONFIG_BOOTSTAGE_USER_COUNT
2474 This is the number of available user bootstage records.
2475 Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
2476 a new ID will be allocated from this stash. If you exceed
2477 the limit, recording will stop.
2479 CONFIG_BOOTSTAGE_REPORT
2480 Define this to print a report before boot, similar to this:
2482 Timer summary in microseconds:
2483 Mark Elapsed Stage
2484 0 0 reset
2485 3,575,678 3,575,678 board_init_f start
2486 3,575,695 17 arch_cpu_init A9
2487 3,575,777 82 arch_cpu_init done
2488 3,659,598 83,821 board_init_r start
2489 3,910,375 250,777 main_loop
2490 29,916,167 26,005,792 bootm_start
2491 30,361,327 445,160 start_kernel
2493 CONFIG_CMD_BOOTSTAGE
2494 Add a 'bootstage' command which supports printing a report
2495 and un/stashing of bootstage data.
2497 CONFIG_BOOTSTAGE_FDT
2498 Stash the bootstage information in the FDT. A root 'bootstage'
2499 node is created with each bootstage id as a child. Each child
2500 has a 'name' property and either 'mark' containing the
2501 mark time in microsecond, or 'accum' containing the
2502 accumulated time for that bootstage id in microseconds.
2503 For example:
2505 bootstage {
2506 154 {
2507 name = "board_init_f";
2508 mark = <3575678>;
2509 };
2510 170 {
2511 name = "lcd";
2512 accum = <33482>;
2513 };
2514 };
2516 Code in the Linux kernel can find this in /proc/devicetree.
2518 Legacy uImage format:
2520 Arg Where When
2521 1 common/cmd_bootm.c before attempting to boot an image
2522 -1 common/cmd_bootm.c Image header has bad magic number
2523 2 common/cmd_bootm.c Image header has correct magic number
2524 -2 common/cmd_bootm.c Image header has bad checksum
2525 3 common/cmd_bootm.c Image header has correct checksum
2526 -3 common/cmd_bootm.c Image data has bad checksum
2527 4 common/cmd_bootm.c Image data has correct checksum
2528 -4 common/cmd_bootm.c Image is for unsupported architecture
2529 5 common/cmd_bootm.c Architecture check OK
2530 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
2531 6 common/cmd_bootm.c Image Type check OK
2532 -6 common/cmd_bootm.c gunzip uncompression error
2533 -7 common/cmd_bootm.c Unimplemented compression type
2534 7 common/cmd_bootm.c Uncompression OK
2535 8 common/cmd_bootm.c No uncompress/copy overwrite error
2536 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
2538 9 common/image.c Start initial ramdisk verification
2539 -10 common/image.c Ramdisk header has bad magic number
2540 -11 common/image.c Ramdisk header has bad checksum
2541 10 common/image.c Ramdisk header is OK
2542 -12 common/image.c Ramdisk data has bad checksum
2543 11 common/image.c Ramdisk data has correct checksum
2544 12 common/image.c Ramdisk verification complete, start loading
2545 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
2546 13 common/image.c Start multifile image verification
2547 14 common/image.c No initial ramdisk, no multifile, continue.
2549 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
2551 -30 arch/powerpc/lib/board.c Fatal error, hang the system
2552 -31 post/post.c POST test failed, detected by post_output_backlog()
2553 -32 post/post.c POST test failed, detected by post_run_single()
2555 34 common/cmd_doc.c before loading a Image from a DOC device
2556 -35 common/cmd_doc.c Bad usage of "doc" command
2557 35 common/cmd_doc.c correct usage of "doc" command
2558 -36 common/cmd_doc.c No boot device
2559 36 common/cmd_doc.c correct boot device
2560 -37 common/cmd_doc.c Unknown Chip ID on boot device
2561 37 common/cmd_doc.c correct chip ID found, device available
2562 -38 common/cmd_doc.c Read Error on boot device
2563 38 common/cmd_doc.c reading Image header from DOC device OK
2564 -39 common/cmd_doc.c Image header has bad magic number
2565 39 common/cmd_doc.c Image header has correct magic number
2566 -40 common/cmd_doc.c Error reading Image from DOC device
2567 40 common/cmd_doc.c Image header has correct magic number
2568 41 common/cmd_ide.c before loading a Image from a IDE device
2569 -42 common/cmd_ide.c Bad usage of "ide" command
2570 42 common/cmd_ide.c correct usage of "ide" command
2571 -43 common/cmd_ide.c No boot device
2572 43 common/cmd_ide.c boot device found
2573 -44 common/cmd_ide.c Device not available
2574 44 common/cmd_ide.c Device available
2575 -45 common/cmd_ide.c wrong partition selected
2576 45 common/cmd_ide.c partition selected
2577 -46 common/cmd_ide.c Unknown partition table
2578 46 common/cmd_ide.c valid partition table found
2579 -47 common/cmd_ide.c Invalid partition type
2580 47 common/cmd_ide.c correct partition type
2581 -48 common/cmd_ide.c Error reading Image Header on boot device
2582 48 common/cmd_ide.c reading Image Header from IDE device OK
2583 -49 common/cmd_ide.c Image header has bad magic number
2584 49 common/cmd_ide.c Image header has correct magic number
2585 -50 common/cmd_ide.c Image header has bad checksum
2586 50 common/cmd_ide.c Image header has correct checksum
2587 -51 common/cmd_ide.c Error reading Image from IDE device
2588 51 common/cmd_ide.c reading Image from IDE device OK
2589 52 common/cmd_nand.c before loading a Image from a NAND device
2590 -53 common/cmd_nand.c Bad usage of "nand" command
2591 53 common/cmd_nand.c correct usage of "nand" command
2592 -54 common/cmd_nand.c No boot device
2593 54 common/cmd_nand.c boot device found
2594 -55 common/cmd_nand.c Unknown Chip ID on boot device
2595 55 common/cmd_nand.c correct chip ID found, device available
2596 -56 common/cmd_nand.c Error reading Image Header on boot device
2597 56 common/cmd_nand.c reading Image Header from NAND device OK
2598 -57 common/cmd_nand.c Image header has bad magic number
2599 57 common/cmd_nand.c Image header has correct magic number
2600 -58 common/cmd_nand.c Error reading Image from NAND device
2601 58 common/cmd_nand.c reading Image from NAND device OK
2603 -60 common/env_common.c Environment has a bad CRC, using default
2605 64 net/eth.c starting with Ethernet configuration.
2606 -64 net/eth.c no Ethernet found.
2607 65 net/eth.c Ethernet found.
2609 -80 common/cmd_net.c usage wrong
2610 80 common/cmd_net.c before calling NetLoop()
2611 -81 common/cmd_net.c some error in NetLoop() occurred
2612 81 common/cmd_net.c NetLoop() back without error
2613 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
2614 82 common/cmd_net.c trying automatic boot
2615 83 common/cmd_net.c running "source" command
2616 -83 common/cmd_net.c some error in automatic boot or "source" command
2617 84 common/cmd_net.c end without errors
2619 FIT uImage format:
2621 Arg Where When
2622 100 common/cmd_bootm.c Kernel FIT Image has correct format
2623 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
2624 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
2625 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
2626 102 common/cmd_bootm.c Kernel unit name specified
2627 -103 common/cmd_bootm.c Can't get kernel subimage node offset
2628 103 common/cmd_bootm.c Found configuration node
2629 104 common/cmd_bootm.c Got kernel subimage node offset
2630 -104 common/cmd_bootm.c Kernel subimage hash verification failed
2631 105 common/cmd_bootm.c Kernel subimage hash verification OK
2632 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
2633 106 common/cmd_bootm.c Architecture check OK
2634 -106 common/cmd_bootm.c Kernel subimage has wrong type
2635 107 common/cmd_bootm.c Kernel subimage type OK
2636 -107 common/cmd_bootm.c Can't get kernel subimage data/size
2637 108 common/cmd_bootm.c Got kernel subimage data/size
2638 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
2639 -109 common/cmd_bootm.c Can't get kernel subimage type
2640 -110 common/cmd_bootm.c Can't get kernel subimage comp
2641 -111 common/cmd_bootm.c Can't get kernel subimage os
2642 -112 common/cmd_bootm.c Can't get kernel subimage load address
2643 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
2645 120 common/image.c Start initial ramdisk verification
2646 -120 common/image.c Ramdisk FIT image has incorrect format
2647 121 common/image.c Ramdisk FIT image has correct format
2648 122 common/image.c No ramdisk subimage unit name, using configuration
2649 -122 common/image.c Can't get configuration for ramdisk subimage
2650 123 common/image.c Ramdisk unit name specified
2651 -124 common/image.c Can't get ramdisk subimage node offset
2652 125 common/image.c Got ramdisk subimage node offset
2653 -125 common/image.c Ramdisk subimage hash verification failed
2654 126 common/image.c Ramdisk subimage hash verification OK
2655 -126 common/image.c Ramdisk subimage for unsupported architecture
2656 127 common/image.c Architecture check OK
2657 -127 common/image.c Can't get ramdisk subimage data/size
2658 128 common/image.c Got ramdisk subimage data/size
2659 129 common/image.c Can't get ramdisk load address
2660 -129 common/image.c Got ramdisk load address
2662 -130 common/cmd_doc.c Incorrect FIT image format
2663 131 common/cmd_doc.c FIT image format OK
2665 -140 common/cmd_ide.c Incorrect FIT image format
2666 141 common/cmd_ide.c FIT image format OK
2668 -150 common/cmd_nand.c Incorrect FIT image format
2669 151 common/cmd_nand.c FIT image format OK
2671 - FIT image support:
2672 CONFIG_FIT
2673 Enable support for the FIT uImage format.
2675 CONFIG_FIT_BEST_MATCH
2676 When no configuration is explicitly selected, default to the
2677 one whose fdt's compatibility field best matches that of
2678 U-Boot itself. A match is considered "best" if it matches the
2679 most specific compatibility entry of U-Boot's fdt's root node.
2680 The order of entries in the configuration's fdt is ignored.
2682 - Standalone program support:
2683 CONFIG_STANDALONE_LOAD_ADDR
2685 This option defines a board specific value for the
2686 address where standalone program gets loaded, thus
2687 overwriting the architecture dependent default
2688 settings.
2690 - Frame Buffer Address:
2691 CONFIG_FB_ADDR
2693 Define CONFIG_FB_ADDR if you want to use specific
2694 address for frame buffer.
2695 Then system will reserve the frame buffer address to
2696 defined address instead of lcd_setmem (this function
2697 grabs the memory for frame buffer by panel's size).
2699 Please see board_init_f function.
2701 - Automatic software updates via TFTP server
2702 CONFIG_UPDATE_TFTP
2703 CONFIG_UPDATE_TFTP_CNT_MAX
2704 CONFIG_UPDATE_TFTP_MSEC_MAX
2706 These options enable and control the auto-update feature;
2707 for a more detailed description refer to doc/README.update.
2709 - MTD Support (mtdparts command, UBI support)
2710 CONFIG_MTD_DEVICE
2712 Adds the MTD device infrastructure from the Linux kernel.
2713 Needed for mtdparts command support.
2715 CONFIG_MTD_PARTITIONS
2717 Adds the MTD partitioning infrastructure from the Linux
2718 kernel. Needed for UBI support.
2720 - SPL framework
2721 CONFIG_SPL
2722 Enable building of SPL globally.
2724 CONFIG_SPL_LDSCRIPT
2725 LDSCRIPT for linking the SPL binary.
2727 CONFIG_SPL_MAX_SIZE
2728 Maximum binary size (text, data and rodata) of the SPL binary.
2730 CONFIG_SPL_TEXT_BASE
2731 TEXT_BASE for linking the SPL binary.
2733 CONFIG_SPL_RELOC_TEXT_BASE
2734 Address to relocate to. If unspecified, this is equal to
2735 CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
2737 CONFIG_SPL_BSS_START_ADDR
2738 Link address for the BSS within the SPL binary.
2740 CONFIG_SPL_BSS_MAX_SIZE
2741 Maximum binary size of the BSS section of the SPL binary.
2743 CONFIG_SPL_STACK
2744 Adress of the start of the stack SPL will use
2746 CONFIG_SPL_RELOC_STACK
2747 Adress of the start of the stack SPL will use after
2748 relocation. If unspecified, this is equal to
2749 CONFIG_SPL_STACK.
2751 CONFIG_SYS_SPL_MALLOC_START
2752 Starting address of the malloc pool used in SPL.
2754 CONFIG_SYS_SPL_MALLOC_SIZE
2755 The size of the malloc pool used in SPL.
2757 CONFIG_SPL_FRAMEWORK
2758 Enable the SPL framework under common/. This framework
2759 supports MMC, NAND and YMODEM loading of U-Boot and NAND
2760 NAND loading of the Linux Kernel.
2762 CONFIG_SPL_DISPLAY_PRINT
2763 For ARM, enable an optional function to print more information
2764 about the running system.
2766 CONFIG_SPL_INIT_MINIMAL
2767 Arch init code should be built for a very small image
2769 CONFIG_SPL_LIBCOMMON_SUPPORT
2770 Support for common/libcommon.o in SPL binary
2772 CONFIG_SPL_LIBDISK_SUPPORT
2773 Support for disk/libdisk.o in SPL binary
2775 CONFIG_SPL_I2C_SUPPORT
2776 Support for drivers/i2c/libi2c.o in SPL binary
2778 CONFIG_SPL_GPIO_SUPPORT
2779 Support for drivers/gpio/libgpio.o in SPL binary
2781 CONFIG_SPL_MMC_SUPPORT
2782 Support for drivers/mmc/libmmc.o in SPL binary
2784 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
2785 CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
2786 CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION
2787 Address, size and partition on the MMC to load U-Boot from
2788 when the MMC is being used in raw mode.
2790 CONFIG_SPL_FAT_SUPPORT
2791 Support for fs/fat/libfat.o in SPL binary
2793 CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
2794 Filename to read to load U-Boot when reading from FAT
2796 CONFIG_SPL_NAND_BASE
2797 Include nand_base.c in the SPL. Requires
2798 CONFIG_SPL_NAND_DRIVERS.
2800 CONFIG_SPL_NAND_DRIVERS
2801 SPL uses normal NAND drivers, not minimal drivers.
2803 CONFIG_SPL_NAND_ECC
2804 Include standard software ECC in the SPL
2806 CONFIG_SPL_NAND_SIMPLE
2807 Support for NAND boot using simple NAND drivers that
2808 expose the cmd_ctrl() interface.
2810 CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
2811 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
2812 CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
2813 CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
2814 CONFIG_SYS_NAND_ECCBYTES
2815 Defines the size and behavior of the NAND that SPL uses
2816 to read U-Boot
2818 CONFIG_SYS_NAND_U_BOOT_OFFS
2819 Location in NAND to read U-Boot from
2821 CONFIG_SYS_NAND_U_BOOT_DST
2822 Location in memory to load U-Boot to
2824 CONFIG_SYS_NAND_U_BOOT_SIZE
2825 Size of image to load
2827 CONFIG_SYS_NAND_U_BOOT_START
2828 Entry point in loaded image to jump to
2830 CONFIG_SYS_NAND_HW_ECC_OOBFIRST
2831 Define this if you need to first read the OOB and then the
2832 data. This is used for example on davinci plattforms.
2834 CONFIG_SPL_OMAP3_ID_NAND
2835 Support for an OMAP3-specific set of functions to return the
2836 ID and MFR of the first attached NAND chip, if present.
2838 CONFIG_SPL_SERIAL_SUPPORT
2839 Support for drivers/serial/libserial.o in SPL binary
2841 CONFIG_SPL_SPI_FLASH_SUPPORT
2842 Support for drivers/mtd/spi/libspi_flash.o in SPL binary
2844 CONFIG_SPL_SPI_SUPPORT
2845 Support for drivers/spi/libspi.o in SPL binary
2847 CONFIG_SPL_RAM_DEVICE
2848 Support for running image already present in ram, in SPL binary
2850 CONFIG_SPL_LIBGENERIC_SUPPORT
2851 Support for lib/libgeneric.o in SPL binary
2853 CONFIG_SPL_TARGET
2854 Final target image containing SPL and payload. Some SPLs
2855 use an arch-specific makefile fragment instead, for
2856 example if more than one image needs to be produced.
2858 Modem Support:
2859 --------------
2861 [so far only for SMDK2400 boards]
2863 - Modem support enable:
2864 CONFIG_MODEM_SUPPORT
2866 - RTS/CTS Flow control enable:
2867 CONFIG_HWFLOW
2869 - Modem debug support:
2870 CONFIG_MODEM_SUPPORT_DEBUG
2872 Enables debugging stuff (char screen[1024], dbg())
2873 for modem support. Useful only with BDI2000.
2875 - Interrupt support (PPC):
2877 There are common interrupt_init() and timer_interrupt()
2878 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
2879 for CPU specific initialization. interrupt_init_cpu()
2880 should set decrementer_count to appropriate value. If
2881 CPU resets decrementer automatically after interrupt
2882 (ppc4xx) it should set decrementer_count to zero.
2883 timer_interrupt() calls timer_interrupt_cpu() for CPU
2884 specific handling. If board has watchdog / status_led
2885 / other_activity_monitor it works automatically from
2886 general timer_interrupt().
2888 - General:
2890 In the target system modem support is enabled when a
2891 specific key (key combination) is pressed during
2892 power-on. Otherwise U-Boot will boot normally
2893 (autoboot). The key_pressed() function is called from
2894 board_init(). Currently key_pressed() is a dummy
2895 function, returning 1 and thus enabling modem
2896 initialization.
2898 If there are no modem init strings in the
2899 environment, U-Boot proceed to autoboot; the
2900 previous output (banner, info printfs) will be
2901 suppressed, though.
2903 See also: doc/README.Modem
2905 Board initialization settings:
2906 ------------------------------
2908 During Initialization u-boot calls a number of board specific functions
2909 to allow the preparation of board specific prerequisites, e.g. pin setup
2910 before drivers are initialized. To enable these callbacks the
2911 following configuration macros have to be defined. Currently this is
2912 architecture specific, so please check arch/your_architecture/lib/board.c
2913 typically in board_init_f() and board_init_r().
2915 - CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
2916 - CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
2917 - CONFIG_BOARD_LATE_INIT: Call board_late_init()
2918 - CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
2920 Configuration Settings:
2921 -----------------------
2923 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
2924 undefine this when you're short of memory.
2926 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
2927 width of the commands listed in the 'help' command output.
2929 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
2930 prompt for user input.
2932 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
2934 - CONFIG_SYS_PBSIZE: Buffer size for Console output
2936 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
2938 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
2939 the application (usually a Linux kernel) when it is
2940 booted
2942 - CONFIG_SYS_BAUDRATE_TABLE:
2943 List of legal baudrate settings for this board.
2945 - CONFIG_SYS_CONSOLE_INFO_QUIET
2946 Suppress display of console information at boot.
2948 - CONFIG_SYS_CONSOLE_IS_IN_ENV
2949 If the board specific function
2950 extern int overwrite_console (void);
2951 returns 1, the stdin, stderr and stdout are switched to the
2952 serial port, else the settings in the environment are used.
2954 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
2955 Enable the call to overwrite_console().
2957 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
2958 Enable overwrite of previous console environment settings.
2960 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
2961 Begin and End addresses of the area used by the
2962 simple memory test.
2964 - CONFIG_SYS_ALT_MEMTEST:
2965 Enable an alternate, more extensive memory test.
2967 - CONFIG_SYS_MEMTEST_SCRATCH:
2968 Scratch address used by the alternate memory test
2969 You only need to set this if address zero isn't writeable
2971 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
2972 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
2973 this specified memory area will get subtracted from the top
2974 (end) of RAM and won't get "touched" at all by U-Boot. By
2975 fixing up gd->ram_size the Linux kernel should gets passed
2976 the now "corrected" memory size and won't touch it either.
2977 This should work for arch/ppc and arch/powerpc. Only Linux
2978 board ports in arch/powerpc with bootwrapper support that
2979 recalculate the memory size from the SDRAM controller setup
2980 will have to get fixed in Linux additionally.
2982 This option can be used as a workaround for the 440EPx/GRx
2983 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
2984 be touched.
2986 WARNING: Please make sure that this value is a multiple of
2987 the Linux page size (normally 4k). If this is not the case,
2988 then the end address of the Linux memory will be located at a
2989 non page size aligned address and this could cause major
2990 problems.
2992 - CONFIG_SYS_LOADS_BAUD_CHANGE:
2993 Enable temporary baudrate change while serial download
2995 - CONFIG_SYS_SDRAM_BASE:
2996 Physical start address of SDRAM. _Must_ be 0 here.
2998 - CONFIG_SYS_MBIO_BASE:
2999 Physical start address of Motherboard I/O (if using a
3000 Cogent motherboard)
3002 - CONFIG_SYS_FLASH_BASE:
3003 Physical start address of Flash memory.
3005 - CONFIG_SYS_MONITOR_BASE:
3006 Physical start address of boot monitor code (set by
3007 make config files to be same as the text base address
3008 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
3009 CONFIG_SYS_FLASH_BASE when booting from flash.
3011 - CONFIG_SYS_MONITOR_LEN:
3012 Size of memory reserved for monitor code, used to
3013 determine _at_compile_time_ (!) if the environment is
3014 embedded within the U-Boot image, or in a separate
3015 flash sector.
3017 - CONFIG_SYS_MALLOC_LEN:
3018 Size of DRAM reserved for malloc() use.
3020 - CONFIG_SYS_BOOTM_LEN:
3021 Normally compressed uImages are limited to an
3022 uncompressed size of 8 MBytes. If this is not enough,
3023 you can define CONFIG_SYS_BOOTM_LEN in your board config file
3024 to adjust this setting to your needs.
3026 - CONFIG_SYS_BOOTMAPSZ:
3027 Maximum size of memory mapped by the startup code of
3028 the Linux kernel; all data that must be processed by
3029 the Linux kernel (bd_info, boot arguments, FDT blob if
3030 used) must be put below this limit, unless "bootm_low"
3031 enviroment variable is defined and non-zero. In such case
3032 all data for the Linux kernel must be between "bootm_low"
3033 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
3034 variable "bootm_mapsize" will override the value of
3035 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
3036 then the value in "bootm_size" will be used instead.
3038 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
3039 Enable initrd_high functionality. If defined then the
3040 initrd_high feature is enabled and the bootm ramdisk subcommand
3041 is enabled.
3043 - CONFIG_SYS_BOOT_GET_CMDLINE:
3044 Enables allocating and saving kernel cmdline in space between
3045 "bootm_low" and "bootm_low" + BOOTMAPSZ.
3047 - CONFIG_SYS_BOOT_GET_KBD:
3048 Enables allocating and saving a kernel copy of the bd_info in
3049 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
3051 - CONFIG_SYS_MAX_FLASH_BANKS:
3052 Max number of Flash memory banks
3054 - CONFIG_SYS_MAX_FLASH_SECT:
3055 Max number of sectors on a Flash chip
3057 - CONFIG_SYS_FLASH_ERASE_TOUT:
3058 Timeout for Flash erase operations (in ms)
3060 - CONFIG_SYS_FLASH_WRITE_TOUT:
3061 Timeout for Flash write operations (in ms)
3063 - CONFIG_SYS_FLASH_LOCK_TOUT
3064 Timeout for Flash set sector lock bit operation (in ms)
3066 - CONFIG_SYS_FLASH_UNLOCK_TOUT
3067 Timeout for Flash clear lock bits operation (in ms)
3069 - CONFIG_SYS_FLASH_PROTECTION
3070 If defined, hardware flash sectors protection is used
3071 instead of U-Boot software protection.
3073 - CONFIG_SYS_DIRECT_FLASH_TFTP:
3075 Enable TFTP transfers directly to flash memory;
3076 without this option such a download has to be
3077 performed in two steps: (1) download to RAM, and (2)
3078 copy from RAM to flash.
3080 The two-step approach is usually more reliable, since
3081 you can check if the download worked before you erase
3082 the flash, but in some situations (when system RAM is
3083 too limited to allow for a temporary copy of the
3084 downloaded image) this option may be very useful.
3086 - CONFIG_SYS_FLASH_CFI:
3087 Define if the flash driver uses extra elements in the
3088 common flash structure for storing flash geometry.
3090 - CONFIG_FLASH_CFI_DRIVER
3091 This option also enables the building of the cfi_flash driver
3092 in the drivers directory
3094 - CONFIG_FLASH_CFI_MTD
3095 This option enables the building of the cfi_mtd driver
3096 in the drivers directory. The driver exports CFI flash
3097 to the MTD layer.
3099 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
3100 Use buffered writes to flash.
3102 - CONFIG_FLASH_SPANSION_S29WS_N
3103 s29ws-n MirrorBit flash has non-standard addresses for buffered
3104 write commands.
3106 - CONFIG_SYS_FLASH_QUIET_TEST
3107 If this option is defined, the common CFI flash doesn't
3108 print it's warning upon not recognized FLASH banks. This
3109 is useful, if some of the configured banks are only
3110 optionally available.
3112 - CONFIG_FLASH_SHOW_PROGRESS
3113 If defined (must be an integer), print out countdown
3114 digits and dots. Recommended value: 45 (9..1) for 80
3115 column displays, 15 (3..1) for 40 column displays.
3117 - CONFIG_SYS_RX_ETH_BUFFER:
3118 Defines the number of Ethernet receive buffers. On some
3119 Ethernet controllers it is recommended to set this value
3120 to 8 or even higher (EEPRO100 or 405 EMAC), since all
3121 buffers can be full shortly after enabling the interface
3122 on high Ethernet traffic.
3123 Defaults to 4 if not defined.
3125 - CONFIG_ENV_MAX_ENTRIES
3127 Maximum number of entries in the hash table that is used
3128 internally to store the environment settings. The default
3129 setting is supposed to be generous and should work in most
3130 cases. This setting can be used to tune behaviour; see
3131 lib/hashtable.c for details.
3133 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3134 - CONFIG_ENV_FLAGS_LIST_STATIC
3135 Enable validation of the values given to enviroment variables when
3136 calling env set. Variables can be restricted to only decimal,
3137 hexadecimal, or boolean. If CONFIG_CMD_NET is also defined,
3138 the variables can also be restricted to IP address or MAC address.
3140 The format of the list is:
3141 type_attribute = [s|d|x|b|i|m]
3142 access_atribute = [a|r|o|c]
3143 attributes = type_attribute[access_atribute]
3144 entry = variable_name[:attributes]
3145 list = entry[,list]
3147 The type attributes are:
3148 s - String (default)
3149 d - Decimal
3150 x - Hexadecimal
3151 b - Boolean ([1yYtT|0nNfF])
3152 i - IP address
3153 m - MAC address
3155 The access attributes are:
3156 a - Any (default)
3157 r - Read-only
3158 o - Write-once
3159 c - Change-default
3161 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3162 Define this to a list (string) to define the ".flags"
3163 envirnoment variable in the default or embedded environment.
3165 - CONFIG_ENV_FLAGS_LIST_STATIC
3166 Define this to a list (string) to define validation that
3167 should be done if an entry is not found in the ".flags"
3168 environment variable. To override a setting in the static
3169 list, simply add an entry for the same variable name to the
3170 ".flags" variable.
3172 - CONFIG_ENV_ACCESS_IGNORE_FORCE
3173 If defined, don't allow the -f switch to env set override variable
3174 access flags.
3176 The following definitions that deal with the placement and management
3177 of environment data (variable area); in general, we support the
3178 following configurations:
3180 - CONFIG_BUILD_ENVCRC:
3182 Builds up envcrc with the target environment so that external utils
3183 may easily extract it and embed it in final U-Boot images.
3185 - CONFIG_ENV_IS_IN_FLASH:
3187 Define this if the environment is in flash memory.
3189 a) The environment occupies one whole flash sector, which is
3190 "embedded" in the text segment with the U-Boot code. This
3191 happens usually with "bottom boot sector" or "top boot
3192 sector" type flash chips, which have several smaller
3193 sectors at the start or the end. For instance, such a
3194 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
3195 such a case you would place the environment in one of the
3196 4 kB sectors - with U-Boot code before and after it. With
3197 "top boot sector" type flash chips, you would put the
3198 environment in one of the last sectors, leaving a gap
3199 between U-Boot and the environment.
3201 - CONFIG_ENV_OFFSET:
3203 Offset of environment data (variable area) to the
3204 beginning of flash memory; for instance, with bottom boot
3205 type flash chips the second sector can be used: the offset
3206 for this sector is given here.
3208 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
3210 - CONFIG_ENV_ADDR:
3212 This is just another way to specify the start address of
3213 the flash sector containing the environment (instead of
3214 CONFIG_ENV_OFFSET).
3216 - CONFIG_ENV_SECT_SIZE:
3218 Size of the sector containing the environment.
3221 b) Sometimes flash chips have few, equal sized, BIG sectors.
3222 In such a case you don't want to spend a whole sector for
3223 the environment.
3225 - CONFIG_ENV_SIZE:
3227 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
3228 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
3229 of this flash sector for the environment. This saves
3230 memory for the RAM copy of the environment.
3232 It may also save flash memory if you decide to use this
3233 when your environment is "embedded" within U-Boot code,
3234 since then the remainder of the flash sector could be used
3235 for U-Boot code. It should be pointed out that this is
3236 STRONGLY DISCOURAGED from a robustness point of view:
3237 updating the environment in flash makes it always
3238 necessary to erase the WHOLE sector. If something goes
3239 wrong before the contents has been restored from a copy in
3240 RAM, your target system will be dead.
3242 - CONFIG_ENV_ADDR_REDUND
3243 CONFIG_ENV_SIZE_REDUND
3245 These settings describe a second storage area used to hold
3246 a redundant copy of the environment data, so that there is
3247 a valid backup copy in case there is a power failure during
3248 a "saveenv" operation.
3250 BE CAREFUL! Any changes to the flash layout, and some changes to the
3251 source code will make it necessary to adapt <board>/u-boot.lds*
3252 accordingly!
3255 - CONFIG_ENV_IS_IN_NVRAM:
3257 Define this if you have some non-volatile memory device
3258 (NVRAM, battery buffered SRAM) which you want to use for the
3259 environment.
3261 - CONFIG_ENV_ADDR:
3262 - CONFIG_ENV_SIZE:
3264 These two #defines are used to determine the memory area you
3265 want to use for environment. It is assumed that this memory
3266 can just be read and written to, without any special
3267 provision.
3269 BE CAREFUL! The first access to the environment happens quite early
3270 in U-Boot initalization (when we try to get the setting of for the
3271 console baudrate). You *MUST* have mapped your NVRAM area then, or
3272 U-Boot will hang.
3274 Please note that even with NVRAM we still use a copy of the
3275 environment in RAM: we could work on NVRAM directly, but we want to
3276 keep settings there always unmodified except somebody uses "saveenv"
3277 to save the current settings.
3280 - CONFIG_ENV_IS_IN_EEPROM:
3282 Use this if you have an EEPROM or similar serial access
3283 device and a driver for it.
3285 - CONFIG_ENV_OFFSET:
3286 - CONFIG_ENV_SIZE:
3288 These two #defines specify the offset and size of the
3289 environment area within the total memory of your EEPROM.
3291 - CONFIG_SYS_I2C_EEPROM_ADDR:
3292 If defined, specified the chip address of the EEPROM device.
3293 The default address is zero.
3295 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
3296 If defined, the number of bits used to address bytes in a
3297 single page in the EEPROM device. A 64 byte page, for example
3298 would require six bits.
3300 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
3301 If defined, the number of milliseconds to delay between
3302 page writes. The default is zero milliseconds.
3304 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
3305 The length in bytes of the EEPROM memory array address. Note
3306 that this is NOT the chip address length!
3308 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
3309 EEPROM chips that implement "address overflow" are ones
3310 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
3311 address and the extra bits end up in the "chip address" bit
3312 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
3313 byte chips.
3315 Note that we consider the length of the address field to
3316 still be one byte because the extra address bits are hidden
3317 in the chip address.
3319 - CONFIG_SYS_EEPROM_SIZE:
3320 The size in bytes of the EEPROM device.
3322 - CONFIG_ENV_EEPROM_IS_ON_I2C
3323 define this, if you have I2C and SPI activated, and your
3324 EEPROM, which holds the environment, is on the I2C bus.
3326 - CONFIG_I2C_ENV_EEPROM_BUS
3327 if you have an Environment on an EEPROM reached over
3328 I2C muxes, you can define here, how to reach this
3329 EEPROM. For example:
3331 #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
3333 EEPROM which holds the environment, is reached over
3334 a pca9547 i2c mux with address 0x70, channel 3.
3336 - CONFIG_ENV_IS_IN_DATAFLASH:
3338 Define this if you have a DataFlash memory device which you
3339 want to use for the environment.
3341 - CONFIG_ENV_OFFSET:
3342 - CONFIG_ENV_ADDR:
3343 - CONFIG_ENV_SIZE:
3345 These three #defines specify the offset and size of the
3346 environment area within the total memory of your DataFlash placed
3347 at the specified address.
3349 - CONFIG_ENV_IS_IN_REMOTE:
3351 Define this if you have a remote memory space which you
3352 want to use for the local device's environment.
3354 - CONFIG_ENV_ADDR:
3355 - CONFIG_ENV_SIZE:
3357 These two #defines specify the address and size of the
3358 environment area within the remote memory space. The
3359 local device can get the environment from remote memory
3360 space by SRIO or PCIE links.
3362 BE CAREFUL! For some special cases, the local device can not use
3363 "saveenv" command. For example, the local device will get the
3364 environment stored in a remote NOR flash by SRIO or PCIE link,
3365 but it can not erase, write this NOR flash by SRIO or PCIE interface.
3367 - CONFIG_ENV_IS_IN_NAND:
3369 Define this if you have a NAND device which you want to use
3370 for the environment.
3372 - CONFIG_ENV_OFFSET:
3373 - CONFIG_ENV_SIZE:
3375 These two #defines specify the offset and size of the environment
3376 area within the first NAND device. CONFIG_ENV_OFFSET must be
3377 aligned to an erase block boundary.
3379 - CONFIG_ENV_OFFSET_REDUND (optional):
3381 This setting describes a second storage area of CONFIG_ENV_SIZE
3382 size used to hold a redundant copy of the environment data, so
3383 that there is a valid backup copy in case there is a power failure
3384 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
3385 aligned to an erase block boundary.
3387 - CONFIG_ENV_RANGE (optional):
3389 Specifies the length of the region in which the environment
3390 can be written. This should be a multiple of the NAND device's
3391 block size. Specifying a range with more erase blocks than
3392 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
3393 the range to be avoided.
3395 - CONFIG_ENV_OFFSET_OOB (optional):
3397 Enables support for dynamically retrieving the offset of the
3398 environment from block zero's out-of-band data. The
3399 "nand env.oob" command can be used to record this offset.
3400 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
3401 using CONFIG_ENV_OFFSET_OOB.
3403 - CONFIG_NAND_ENV_DST
3405 Defines address in RAM to which the nand_spl code should copy the
3406 environment. If redundant environment is used, it will be copied to
3407 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
3409 - CONFIG_SYS_SPI_INIT_OFFSET
3411 Defines offset to the initial SPI buffer area in DPRAM. The
3412 area is used at an early stage (ROM part) if the environment
3413 is configured to reside in the SPI EEPROM: We need a 520 byte
3414 scratch DPRAM area. It is used between the two initialization
3415 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
3416 to be a good choice since it makes it far enough from the
3417 start of the data area as well as from the stack pointer.
3419 Please note that the environment is read-only until the monitor
3420 has been relocated to RAM and a RAM copy of the environment has been
3421 created; also, when using EEPROM you will have to use getenv_f()
3422 until then to read environment variables.
3424 The environment is protected by a CRC32 checksum. Before the monitor
3425 is relocated into RAM, as a result of a bad CRC you will be working
3426 with the compiled-in default environment - *silently*!!! [This is
3427 necessary, because the first environment variable we need is the
3428 "baudrate" setting for the console - if we have a bad CRC, we don't
3429 have any device yet where we could complain.]
3431 Note: once the monitor has been relocated, then it will complain if
3432 the default environment is used; a new CRC is computed as soon as you
3433 use the "saveenv" command to store a valid environment.
3435 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
3436 Echo the inverted Ethernet link state to the fault LED.
3438 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
3439 also needs to be defined.
3441 - CONFIG_SYS_FAULT_MII_ADDR:
3442 MII address of the PHY to check for the Ethernet link state.
3444 - CONFIG_NS16550_MIN_FUNCTIONS:
3445 Define this if you desire to only have use of the NS16550_init
3446 and NS16550_putc functions for the serial driver located at
3447 drivers/serial/ns16550.c. This option is useful for saving
3448 space for already greatly restricted images, including but not
3449 limited to NAND_SPL configurations.
3451 Low Level (hardware related) configuration options:
3452 ---------------------------------------------------
3454 - CONFIG_SYS_CACHELINE_SIZE:
3455 Cache Line Size of the CPU.
3457 - CONFIG_SYS_DEFAULT_IMMR:
3458 Default address of the IMMR after system reset.
3460 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
3461 and RPXsuper) to be able to adjust the position of
3462 the IMMR register after a reset.
3464 - CONFIG_SYS_CCSRBAR_DEFAULT:
3465 Default (power-on reset) physical address of CCSR on Freescale
3466 PowerPC SOCs.
3468 - CONFIG_SYS_CCSRBAR:
3469 Virtual address of CCSR. On a 32-bit build, this is typically
3470 the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
3472 CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
3473 for cross-platform code that uses that macro instead.
3475 - CONFIG_SYS_CCSRBAR_PHYS:
3476 Physical address of CCSR. CCSR can be relocated to a new
3477 physical address, if desired. In this case, this macro should
3478 be set to that address. Otherwise, it should be set to the
3479 same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
3480 is typically relocated on 36-bit builds. It is recommended
3481 that this macro be defined via the _HIGH and _LOW macros:
3483 #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
3484 * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
3486 - CONFIG_SYS_CCSRBAR_PHYS_HIGH:
3487 Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
3488 either 0 (32-bit build) or 0xF (36-bit build). This macro is
3489 used in assembly code, so it must not contain typecasts or
3490 integer size suffixes (e.g. "ULL").
3492 - CONFIG_SYS_CCSRBAR_PHYS_LOW:
3493 Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
3494 used in assembly code, so it must not contain typecasts or
3495 integer size suffixes (e.g. "ULL").
3497 - CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
3498 If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
3499 forced to a value that ensures that CCSR is not relocated.
3501 - Floppy Disk Support:
3502 CONFIG_SYS_FDC_DRIVE_NUMBER
3504 the default drive number (default value 0)
3506 CONFIG_SYS_ISA_IO_STRIDE
3508 defines the spacing between FDC chipset registers
3509 (default value 1)
3511 CONFIG_SYS_ISA_IO_OFFSET
3513 defines the offset of register from address. It
3514 depends on which part of the data bus is connected to
3515 the FDC chipset. (default value 0)
3517 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
3518 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
3519 default value.
3521 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
3522 fdc_hw_init() is called at the beginning of the FDC
3523 setup. fdc_hw_init() must be provided by the board
3524 source code. It is used to make hardware dependant
3525 initializations.
3527 - CONFIG_IDE_AHB:
3528 Most IDE controllers were designed to be connected with PCI
3529 interface. Only few of them were designed for AHB interface.
3530 When software is doing ATA command and data transfer to
3531 IDE devices through IDE-AHB controller, some additional
3532 registers accessing to these kind of IDE-AHB controller
3533 is requierd.
3535 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
3536 DO NOT CHANGE unless you know exactly what you're
3537 doing! (11-4) [MPC8xx/82xx systems only]
3539 - CONFIG_SYS_INIT_RAM_ADDR:
3541 Start address of memory area that can be used for
3542 initial data and stack; please note that this must be
3543 writable memory that is working WITHOUT special
3544 initialization, i. e. you CANNOT use normal RAM which
3545 will become available only after programming the
3546 memory controller and running certain initialization
3547 sequences.
3549 U-Boot uses the following memory types:
3550 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
3551 - MPC824X: data cache
3552 - PPC4xx: data cache
3554 - CONFIG_SYS_GBL_DATA_OFFSET:
3556 Offset of the initial data structure in the memory
3557 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
3558 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
3559 data is located at the end of the available space
3560 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
3561 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
3562 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
3563 CONFIG_SYS_GBL_DATA_OFFSET) downward.
3565 Note:
3566 On the MPC824X (or other systems that use the data
3567 cache for initial memory) the address chosen for
3568 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
3569 point to an otherwise UNUSED address space between
3570 the top of RAM and the start of the PCI space.
3572 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
3574 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
3576 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
3578 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
3580 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
3582 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
3584 - CONFIG_SYS_OR_TIMING_SDRAM:
3585 SDRAM timing
3587 - CONFIG_SYS_MAMR_PTA:
3588 periodic timer for refresh
3590 - CONFIG_SYS_DER: Debug Event Register (37-47)
3592 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
3593 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
3594 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
3595 CONFIG_SYS_BR1_PRELIM:
3596 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
3598 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
3599 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
3600 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
3601 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
3603 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
3604 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
3605 Machine Mode Register and Memory Periodic Timer
3606 Prescaler definitions (SDRAM timing)
3608 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
3609 enable I2C microcode relocation patch (MPC8xx);
3610 define relocation offset in DPRAM [DSP2]
3612 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
3613 enable SMC microcode relocation patch (MPC8xx);
3614 define relocation offset in DPRAM [SMC1]
3616 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
3617 enable SPI microcode relocation patch (MPC8xx);
3618 define relocation offset in DPRAM [SCC4]
3620 - CONFIG_SYS_USE_OSCCLK:
3621 Use OSCM clock mode on MBX8xx board. Be careful,
3622 wrong setting might damage your board. Read
3623 doc/README.MBX before setting this variable!
3625 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
3626 Offset of the bootmode word in DPRAM used by post
3627 (Power On Self Tests). This definition overrides
3628 #define'd default value in commproc.h resp.
3629 cpm_8260.h.
3631 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
3632 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
3633 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
3634 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
3635 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
3636 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
3637 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
3638 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
3639 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
3641 - CONFIG_PCI_DISABLE_PCIE:
3642 Disable PCI-Express on systems where it is supported but not
3643 required.
3645 - CONFIG_PCI_ENUM_ONLY
3646 Only scan through and get the devices on the busses.
3647 Don't do any setup work, presumably because someone or
3648 something has already done it, and we don't need to do it
3649 a second time. Useful for platforms that are pre-booted
3650 by coreboot or similar.
3652 - CONFIG_SYS_SRIO:
3653 Chip has SRIO or not
3655 - CONFIG_SRIO1:
3656 Board has SRIO 1 port available
3658 - CONFIG_SRIO2:
3659 Board has SRIO 2 port available
3661 - CONFIG_SYS_SRIOn_MEM_VIRT:
3662 Virtual Address of SRIO port 'n' memory region
3664 - CONFIG_SYS_SRIOn_MEM_PHYS:
3665 Physical Address of SRIO port 'n' memory region
3667 - CONFIG_SYS_SRIOn_MEM_SIZE:
3668 Size of SRIO port 'n' memory region
3670 - CONFIG_SYS_NDFC_16
3671 Defined to tell the NDFC that the NAND chip is using a
3672 16 bit bus.
3674 - CONFIG_SYS_NDFC_EBC0_CFG
3675 Sets the EBC0_CFG register for the NDFC. If not defined
3676 a default value will be used.
3678 - CONFIG_SPD_EEPROM
3679 Get DDR timing information from an I2C EEPROM. Common
3680 with pluggable memory modules such as SODIMMs
3682 SPD_EEPROM_ADDRESS
3683 I2C address of the SPD EEPROM
3685 - CONFIG_SYS_SPD_BUS_NUM
3686 If SPD EEPROM is on an I2C bus other than the first
3687 one, specify here. Note that the value must resolve
3688 to something your driver can deal with.
3690 - CONFIG_SYS_DDR_RAW_TIMING
3691 Get DDR timing information from other than SPD. Common with
3692 soldered DDR chips onboard without SPD. DDR raw timing
3693 parameters are extracted from datasheet and hard-coded into
3694 header files or board specific files.
3696 - CONFIG_FSL_DDR_INTERACTIVE
3697 Enable interactive DDR debugging. See doc/README.fsl-ddr.
3699 - CONFIG_SYS_83XX_DDR_USES_CS0
3700 Only for 83xx systems. If specified, then DDR should
3701 be configured using CS0 and CS1 instead of CS2 and CS3.
3703 - CONFIG_ETHER_ON_FEC[12]
3704 Define to enable FEC[12] on a 8xx series processor.
3706 - CONFIG_FEC[12]_PHY
3707 Define to the hardcoded PHY address which corresponds
3708 to the given FEC; i. e.
3709 #define CONFIG_FEC1_PHY 4
3710 means that the PHY with address 4 is connected to FEC1
3712 When set to -1, means to probe for first available.
3714 - CONFIG_FEC[12]_PHY_NORXERR
3715 The PHY does not have a RXERR line (RMII only).
3716 (so program the FEC to ignore it).
3718 - CONFIG_RMII
3719 Enable RMII mode for all FECs.
3720 Note that this is a global option, we can't
3721 have one FEC in standard MII mode and another in RMII mode.
3723 - CONFIG_CRC32_VERIFY
3724 Add a verify option to the crc32 command.
3725 The syntax is:
3727 => crc32 -v <address> <count> <crc32>
3729 Where address/count indicate a memory area
3730 and crc32 is the correct crc32 which the
3731 area should have.
3733 - CONFIG_LOOPW
3734 Add the "loopw" memory command. This only takes effect if
3735 the memory commands are activated globally (CONFIG_CMD_MEM).
3737 - CONFIG_MX_CYCLIC
3738 Add the "mdc" and "mwc" memory commands. These are cyclic
3739 "md/mw" commands.
3740 Examples:
3742 => mdc.b 10 4 500
3743 This command will print 4 bytes (10,11,12,13) each 500 ms.
3745 => mwc.l 100 12345678 10
3746 This command will write 12345678 to address 100 all 10 ms.
3748 This only takes effect if the memory commands are activated
3749 globally (CONFIG_CMD_MEM).
3751 - CONFIG_SKIP_LOWLEVEL_INIT
3752 [ARM, NDS32, MIPS only] If this variable is defined, then certain
3753 low level initializations (like setting up the memory
3754 controller) are omitted and/or U-Boot does not
3755 relocate itself into RAM.
3757 Normally this variable MUST NOT be defined. The only
3758 exception is when U-Boot is loaded (to RAM) by some
3759 other boot loader or by a debugger which performs
3760 these initializations itself.
3762 - CONFIG_SPL_BUILD
3763 Modifies the behaviour of start.S when compiling a loader
3764 that is executed before the actual U-Boot. E.g. when
3765 compiling a NAND SPL.
3767 - CONFIG_USE_ARCH_MEMCPY
3768 CONFIG_USE_ARCH_MEMSET
3769 If these options are used a optimized version of memcpy/memset will
3770 be used if available. These functions may be faster under some
3771 conditions but may increase the binary size.
3773 - CONFIG_X86_NO_RESET_VECTOR
3774 If defined, the x86 reset vector code is excluded. You will need
3775 to do this when U-Boot is running from Coreboot.
3777 - CONFIG_X86_NO_REAL_MODE
3778 If defined, x86 real mode code is omitted. This assumes a
3779 32-bit environment where such code is not needed. You will
3780 need to do this when U-Boot is running from Coreboot.
3783 Freescale QE/FMAN Firmware Support:
3784 -----------------------------------
3786 The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
3787 loading of "firmware", which is encoded in the QE firmware binary format.
3788 This firmware often needs to be loaded during U-Boot booting, so macros
3789 are used to identify the storage device (NOR flash, SPI, etc) and the address
3790 within that device.
3792 - CONFIG_SYS_QE_FMAN_FW_ADDR
3793 The address in the storage device where the firmware is located. The
3794 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
3795 is also specified.
3797 - CONFIG_SYS_QE_FMAN_FW_LENGTH
3798 The maximum possible size of the firmware. The firmware binary format
3799 has a field that specifies the actual size of the firmware, but it
3800 might not be possible to read any part of the firmware unless some
3801 local storage is allocated to hold the entire firmware first.
3803 - CONFIG_SYS_QE_FMAN_FW_IN_NOR
3804 Specifies that QE/FMAN firmware is located in NOR flash, mapped as
3805 normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
3806 virtual address in NOR flash.
3808 - CONFIG_SYS_QE_FMAN_FW_IN_NAND
3809 Specifies that QE/FMAN firmware is located in NAND flash.
3810 CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
3812 - CONFIG_SYS_QE_FMAN_FW_IN_MMC
3813 Specifies that QE/FMAN firmware is located on the primary SD/MMC
3814 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
3816 - CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
3817 Specifies that QE/FMAN firmware is located on the primary SPI
3818 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
3820 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
3821 Specifies that QE/FMAN firmware is located in the remote (master)
3822 memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
3823 can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
3824 window->master inbound window->master LAW->the ucode address in
3825 master's memory space.
3827 Building the Software:
3828 ======================
3830 Building U-Boot has been tested in several native build environments
3831 and in many different cross environments. Of course we cannot support
3832 all possibly existing versions of cross development tools in all
3833 (potentially obsolete) versions. In case of tool chain problems we
3834 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
3835 which is extensively used to build and test U-Boot.
3837 If you are not using a native environment, it is assumed that you
3838 have GNU cross compiling tools available in your path. In this case,
3839 you must set the environment variable CROSS_COMPILE in your shell.
3840 Note that no changes to the Makefile or any other source files are
3841 necessary. For example using the ELDK on a 4xx CPU, please enter:
3843 $ CROSS_COMPILE=ppc_4xx-
3844 $ export CROSS_COMPILE
3846 Note: If you wish to generate Windows versions of the utilities in
3847 the tools directory you can use the MinGW toolchain
3848 (http://www.mingw.org). Set your HOST tools to the MinGW
3849 toolchain and execute 'make tools'. For example:
3851 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
3853 Binaries such as tools/mkimage.exe will be created which can
3854 be executed on computers running Windows.
3856 U-Boot is intended to be simple to build. After installing the
3857 sources you must configure U-Boot for one specific board type. This
3858 is done by typing:
3860 make NAME_config
3862 where "NAME_config" is the name of one of the existing configu-
3863 rations; see boards.cfg for supported names.
3865 Note: for some board special configuration names may exist; check if
3866 additional information is available from the board vendor; for
3867 instance, the TQM823L systems are available without (standard)
3868 or with LCD support. You can select such additional "features"
3869 when choosing the configuration, i. e.
3871 make TQM823L_config
3872 - will configure for a plain TQM823L, i. e. no LCD support
3874 make TQM823L_LCD_config
3875 - will configure for a TQM823L with U-Boot console on LCD
3877 etc.
3880 Finally, type "make all", and you should get some working U-Boot
3881 images ready for download to / installation on your system:
3883 - "u-boot.bin" is a raw binary image
3884 - "u-boot" is an image in ELF binary format
3885 - "u-boot.srec" is in Motorola S-Record format
3887 By default the build is performed locally and the objects are saved
3888 in the source directory. One of the two methods can be used to change
3889 this behavior and build U-Boot to some external directory:
3891 1. Add O= to the make command line invocations:
3893 make O=/tmp/build distclean
3894 make O=/tmp/build NAME_config
3895 make O=/tmp/build all
3897 2. Set environment variable BUILD_DIR to point to the desired location:
3899 export BUILD_DIR=/tmp/build
3900 make distclean
3901 make NAME_config
3902 make all
3904 Note that the command line "O=" setting overrides the BUILD_DIR environment
3905 variable.
3908 Please be aware that the Makefiles assume you are using GNU make, so
3909 for instance on NetBSD you might need to use "gmake" instead of
3910 native "make".
3913 If the system board that you have is not listed, then you will need
3914 to port U-Boot to your hardware platform. To do this, follow these
3915 steps:
3917 1. Add a new configuration option for your board to the toplevel
3918 "boards.cfg" file, using the existing entries as examples.
3919 Follow the instructions there to keep the boards in order.
3920 2. Create a new directory to hold your board specific code. Add any
3921 files you need. In your board directory, you will need at least
3922 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
3923 3. Create a new configuration file "include/configs/<board>.h" for
3924 your board
3925 3. If you're porting U-Boot to a new CPU, then also create a new
3926 directory to hold your CPU specific code. Add any files you need.
3927 4. Run "make <board>_config" with your new name.
3928 5. Type "make", and you should get a working "u-boot.srec" file
3929 to be installed on your target system.
3930 6. Debug and solve any problems that might arise.
3931 [Of course, this last step is much harder than it sounds.]
3934 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
3935 ==============================================================
3937 If you have modified U-Boot sources (for instance added a new board
3938 or support for new devices, a new CPU, etc.) you are expected to
3939 provide feedback to the other developers. The feedback normally takes
3940 the form of a "patch", i. e. a context diff against a certain (latest
3941 official or latest in the git repository) version of U-Boot sources.
3943 But before you submit such a patch, please verify that your modifi-
3944 cation did not break existing code. At least make sure that *ALL* of
3945 the supported boards compile WITHOUT ANY compiler warnings. To do so,
3946 just run the "MAKEALL" script, which will configure and build U-Boot
3947 for ALL supported system. Be warned, this will take a while. You can
3948 select which (cross) compiler to use by passing a `CROSS_COMPILE'
3949 environment variable to the script, i. e. to use the ELDK cross tools
3950 you can type
3952 CROSS_COMPILE=ppc_8xx- MAKEALL
3954 or to build on a native PowerPC system you can type
3956 CROSS_COMPILE=' ' MAKEALL
3958 When using the MAKEALL script, the default behaviour is to build
3959 U-Boot in the source directory. This location can be changed by
3960 setting the BUILD_DIR environment variable. Also, for each target
3961 built, the MAKEALL script saves two log files (<target>.ERR and
3962 <target>.MAKEALL) in the <source dir>/LOG directory. This default
3963 location can be changed by setting the MAKEALL_LOGDIR environment
3964 variable. For example:
3966 export BUILD_DIR=/tmp/build
3967 export MAKEALL_LOGDIR=/tmp/log
3968 CROSS_COMPILE=ppc_8xx- MAKEALL
3970 With the above settings build objects are saved in the /tmp/build,
3971 log files are saved in the /tmp/log and the source tree remains clean
3972 during the whole build process.
3975 See also "U-Boot Porting Guide" below.
3978 Monitor Commands - Overview:
3979 ============================
3981 go - start application at address 'addr'
3982 run - run commands in an environment variable
3983 bootm - boot application image from memory
3984 bootp - boot image via network using BootP/TFTP protocol
3985 bootz - boot zImage from memory
3986 tftpboot- boot image via network using TFTP protocol
3987 and env variables "ipaddr" and "serverip"
3988 (and eventually "gatewayip")
3989 tftpput - upload a file via network using TFTP protocol
3990 rarpboot- boot image via network using RARP/TFTP protocol
3991 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
3992 loads - load S-Record file over serial line
3993 loadb - load binary file over serial line (kermit mode)
3994 md - memory display
3995 mm - memory modify (auto-incrementing)
3996 nm - memory modify (constant address)
3997 mw - memory write (fill)
3998 cp - memory copy
3999 cmp - memory compare
4000 crc32 - checksum calculation
4001 i2c - I2C sub-system
4002 sspi - SPI utility commands
4003 base - print or set address offset
4004 printenv- print environment variables
4005 setenv - set environment variables
4006 saveenv - save environment variables to persistent storage
4007 protect - enable or disable FLASH write protection
4008 erase - erase FLASH memory
4009 flinfo - print FLASH memory information
4010 nand - NAND memory operations (see doc/README.nand)
4011 bdinfo - print Board Info structure
4012 iminfo - print header information for application image
4013 coninfo - print console devices and informations
4014 ide - IDE sub-system
4015 loop - infinite loop on address range
4016 loopw - infinite write loop on address range
4017 mtest - simple RAM test
4018 icache - enable or disable instruction cache
4019 dcache - enable or disable data cache
4020 reset - Perform RESET of the CPU
4021 echo - echo args to console
4022 version - print monitor version
4023 help - print online help
4024 ? - alias for 'help'
4027 Monitor Commands - Detailed Description:
4028 ========================================
4030 TODO.
4032 For now: just type "help <command>".
4035 Environment Variables:
4036 ======================
4038 U-Boot supports user configuration using Environment Variables which
4039 can be made persistent by saving to Flash memory.
4041 Environment Variables are set using "setenv", printed using
4042 "printenv", and saved to Flash using "saveenv". Using "setenv"
4043 without a value can be used to delete a variable from the
4044 environment. As long as you don't save the environment you are
4045 working with an in-memory copy. In case the Flash area containing the
4046 environment is erased by accident, a default environment is provided.
4048 Some configuration options can be set using Environment Variables.
4050 List of environment variables (most likely not complete):
4052 baudrate - see CONFIG_BAUDRATE
4054 bootdelay - see CONFIG_BOOTDELAY
4056 bootcmd - see CONFIG_BOOTCOMMAND
4058 bootargs - Boot arguments when booting an RTOS image
4060 bootfile - Name of the image to load with TFTP
4062 bootm_low - Memory range available for image processing in the bootm
4063 command can be restricted. This variable is given as
4064 a hexadecimal number and defines lowest address allowed
4065 for use by the bootm command. See also "bootm_size"
4066 environment variable. Address defined by "bootm_low" is
4067 also the base of the initial memory mapping for the Linux
4068 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
4069 bootm_mapsize.
4071 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
4072 This variable is given as a hexadecimal number and it
4073 defines the size of the memory region starting at base
4074 address bootm_low that is accessible by the Linux kernel
4075 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
4076 as the default value if it is defined, and bootm_size is
4077 used otherwise.
4079 bootm_size - Memory range available for image processing in the bootm
4080 command can be restricted. This variable is given as
4081 a hexadecimal number and defines the size of the region
4082 allowed for use by the bootm command. See also "bootm_low"
4083 environment variable.
4085 updatefile - Location of the software update file on a TFTP server, used
4086 by the automatic software update feature. Please refer to
4087 documentation in doc/README.update for more details.
4089 autoload - if set to "no" (any string beginning with 'n'),
4090 "bootp" will just load perform a lookup of the
4091 configuration from the BOOTP server, but not try to
4092 load any image using TFTP
4094 autostart - if set to "yes", an image loaded using the "bootp",
4095 "rarpboot", "tftpboot" or "diskboot" commands will
4096 be automatically started (by internally calling
4097 "bootm")
4099 If set to "no", a standalone image passed to the
4100 "bootm" command will be copied to the load address
4101 (and eventually uncompressed), but NOT be started.
4102 This can be used to load and uncompress arbitrary
4103 data.
4105 fdt_high - if set this restricts the maximum address that the
4106 flattened device tree will be copied into upon boot.
4107 For example, if you have a system with 1 GB memory
4108 at physical address 0x10000000, while Linux kernel
4109 only recognizes the first 704 MB as low memory, you
4110 may need to set fdt_high as 0x3C000000 to have the
4111 device tree blob be copied to the maximum address
4112 of the 704 MB low memory, so that Linux kernel can
4113 access it during the boot procedure.
4115 If this is set to the special value 0xFFFFFFFF then
4116 the fdt will not be copied at all on boot. For this
4117 to work it must reside in writable memory, have
4118 sufficient padding on the end of it for u-boot to
4119 add the information it needs into it, and the memory
4120 must be accessible by the kernel.
4122 fdtcontroladdr- if set this is the address of the control flattened
4123 device tree used by U-Boot when CONFIG_OF_CONTROL is
4124 defined.
4126 i2cfast - (PPC405GP|PPC405EP only)
4127 if set to 'y' configures Linux I2C driver for fast
4128 mode (400kHZ). This environment variable is used in
4129 initialization code. So, for changes to be effective
4130 it must be saved and board must be reset.
4132 initrd_high - restrict positioning of initrd images:
4133 If this variable is not set, initrd images will be
4134 copied to the highest possible address in RAM; this
4135 is usually what you want since it allows for
4136 maximum initrd size. If for some reason you want to
4137 make sure that the initrd image is loaded below the
4138 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
4139 variable to a value of "no" or "off" or "0".
4140 Alternatively, you can set it to a maximum upper
4141 address to use (U-Boot will still check that it
4142 does not overwrite the U-Boot stack and data).
4144 For instance, when you have a system with 16 MB
4145 RAM, and want to reserve 4 MB from use by Linux,
4146 you can do this by adding "mem=12M" to the value of
4147 the "bootargs" variable. However, now you must make
4148 sure that the initrd image is placed in the first
4149 12 MB as well - this can be done with
4151 setenv initrd_high 00c00000
4153 If you set initrd_high to 0xFFFFFFFF, this is an
4154 indication to U-Boot that all addresses are legal
4155 for the Linux kernel, including addresses in flash
4156 memory. In this case U-Boot will NOT COPY the
4157 ramdisk at all. This may be useful to reduce the
4158 boot time on your system, but requires that this
4159 feature is supported by your Linux kernel.
4161 ipaddr - IP address; needed for tftpboot command
4163 loadaddr - Default load address for commands like "bootp",
4164 "rarpboot", "tftpboot", "loadb" or "diskboot"
4166 loads_echo - see CONFIG_LOADS_ECHO
4168 serverip - TFTP server IP address; needed for tftpboot command
4170 bootretry - see CONFIG_BOOT_RETRY_TIME
4172 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
4174 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
4176 ethprime - controls which interface is used first.
4178 ethact - controls which interface is currently active.
4179 For example you can do the following
4181 => setenv ethact FEC
4182 => ping 192.168.0.1 # traffic sent on FEC
4183 => setenv ethact SCC
4184 => ping 10.0.0.1 # traffic sent on SCC
4186 ethrotate - When set to "no" U-Boot does not go through all
4187 available network interfaces.
4188 It just stays at the currently selected interface.
4190 netretry - When set to "no" each network operation will
4191 either succeed or fail without retrying.
4192 When set to "once" the network operation will
4193 fail when all the available network interfaces
4194 are tried once without success.
4195 Useful on scripts which control the retry operation
4196 themselves.
4198 npe_ucode - set load address for the NPE microcode
4200 tftpsrcport - If this is set, the value is used for TFTP's
4201 UDP source port.
4203 tftpdstport - If this is set, the value is used for TFTP's UDP
4204 destination port instead of the Well Know Port 69.
4206 tftpblocksize - Block size to use for TFTP transfers; if not set,
4207 we use the TFTP server's default block size
4209 tftptimeout - Retransmission timeout for TFTP packets (in milli-
4210 seconds, minimum value is 1000 = 1 second). Defines
4211 when a packet is considered to be lost so it has to
4212 be retransmitted. The default is 5000 = 5 seconds.
4213 Lowering this value may make downloads succeed
4214 faster in networks with high packet loss rates or
4215 with unreliable TFTP servers.
4217 vlan - When set to a value < 4095 the traffic over
4218 Ethernet is encapsulated/received over 802.1q
4219 VLAN tagged frames.
4221 The following image location variables contain the location of images
4222 used in booting. The "Image" column gives the role of the image and is
4223 not an environment variable name. The other columns are environment
4224 variable names. "File Name" gives the name of the file on a TFTP
4225 server, "RAM Address" gives the location in RAM the image will be
4226 loaded to, and "Flash Location" gives the image's address in NOR
4227 flash or offset in NAND flash.
4229 *Note* - these variables don't have to be defined for all boards, some
4230 boards currenlty use other variables for these purposes, and some
4231 boards use these variables for other purposes.
4233 Image File Name RAM Address Flash Location
4234 ----- --------- ----------- --------------
4235 u-boot u-boot u-boot_addr_r u-boot_addr
4236 Linux kernel bootfile kernel_addr_r kernel_addr
4237 device tree blob fdtfile fdt_addr_r fdt_addr
4238 ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
4240 The following environment variables may be used and automatically
4241 updated by the network boot commands ("bootp" and "rarpboot"),
4242 depending the information provided by your boot server:
4244 bootfile - see above
4245 dnsip - IP address of your Domain Name Server
4246 dnsip2 - IP address of your secondary Domain Name Server
4247 gatewayip - IP address of the Gateway (Router) to use
4248 hostname - Target hostname
4249 ipaddr - see above
4250 netmask - Subnet Mask
4251 rootpath - Pathname of the root filesystem on the NFS server
4252 serverip - see above
4255 There are two special Environment Variables:
4257 serial# - contains hardware identification information such
4258 as type string and/or serial number
4259 ethaddr - Ethernet address
4261 These variables can be set only once (usually during manufacturing of
4262 the board). U-Boot refuses to delete or overwrite these variables
4263 once they have been set once.
4266 Further special Environment Variables:
4268 ver - Contains the U-Boot version string as printed
4269 with the "version" command. This variable is
4270 readonly (see CONFIG_VERSION_VARIABLE).
4273 Please note that changes to some configuration parameters may take
4274 only effect after the next boot (yes, that's just like Windoze :-).
4277 Callback functions for environment variables:
4278 ---------------------------------------------
4280 For some environment variables, the behavior of u-boot needs to change
4281 when their values are changed. This functionailty allows functions to
4282 be associated with arbitrary variables. On creation, overwrite, or
4283 deletion, the callback will provide the opportunity for some side
4284 effect to happen or for the change to be rejected.
4286 The callbacks are named and associated with a function using the
4287 U_BOOT_ENV_CALLBACK macro in your board or driver code.
4289 These callbacks are associated with variables in one of two ways. The
4290 static list can be added to by defining CONFIG_ENV_CALLBACK_LIST_STATIC
4291 in the board configuration to a string that defines a list of
4292 associations. The list must be in the following format:
4294 entry = variable_name[:callback_name]
4295 list = entry[,list]
4297 If the callback name is not specified, then the callback is deleted.
4298 Spaces are also allowed anywhere in the list.
4300 Callbacks can also be associated by defining the ".callbacks" variable
4301 with the same list format above. Any association in ".callbacks" will
4302 override any association in the static list. You can define
4303 CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
4304 ".callbacks" envirnoment variable in the default or embedded environment.
4307 Command Line Parsing:
4308 =====================
4310 There are two different command line parsers available with U-Boot:
4311 the old "simple" one, and the much more powerful "hush" shell:
4313 Old, simple command line parser:
4314 --------------------------------
4316 - supports environment variables (through setenv / saveenv commands)
4317 - several commands on one line, separated by ';'
4318 - variable substitution using "... ${name} ..." syntax
4319 - special characters ('$', ';') can be escaped by prefixing with '\',
4320 for example:
4321 setenv bootcmd bootm \${address}
4322 - You can also escape text by enclosing in single apostrophes, for example:
4323 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
4325 Hush shell:
4326 -----------
4328 - similar to Bourne shell, with control structures like
4329 if...then...else...fi, for...do...done; while...do...done,
4330 until...do...done, ...
4331 - supports environment ("global") variables (through setenv / saveenv
4332 commands) and local shell variables (through standard shell syntax
4333 "name=value"); only environment variables can be used with "run"
4334 command
4336 General rules:
4337 --------------
4339 (1) If a command line (or an environment variable executed by a "run"
4340 command) contains several commands separated by semicolon, and
4341 one of these commands fails, then the remaining commands will be
4342 executed anyway.
4344 (2) If you execute several variables with one call to run (i. e.
4345 calling run with a list of variables as arguments), any failing
4346 command will cause "run" to terminate, i. e. the remaining
4347 variables are not executed.
4349 Note for Redundant Ethernet Interfaces:
4350 =======================================
4352 Some boards come with redundant Ethernet interfaces; U-Boot supports
4353 such configurations and is capable of automatic selection of a
4354 "working" interface when needed. MAC assignment works as follows:
4356 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
4357 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
4358 "eth1addr" (=>eth1), "eth2addr", ...
4360 If the network interface stores some valid MAC address (for instance
4361 in SROM), this is used as default address if there is NO correspon-
4362 ding setting in the environment; if the corresponding environment
4363 variable is set, this overrides the settings in the card; that means:
4365 o If the SROM has a valid MAC address, and there is no address in the
4366 environment, the SROM's address is used.
4368 o If there is no valid address in the SROM, and a definition in the
4369 environment exists, then the value from the environment variable is
4370 used.
4372 o If both the SROM and the environment contain a MAC address, and
4373 both addresses are the same, this MAC address is used.
4375 o If both the SROM and the environment contain a MAC address, and the
4376 addresses differ, the value from the environment is used and a
4377 warning is printed.
4379 o If neither SROM nor the environment contain a MAC address, an error
4380 is raised.
4382 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
4383 will be programmed into hardware as part of the initialization process. This
4384 may be skipped by setting the appropriate 'ethmacskip' environment variable.
4385 The naming convention is as follows:
4386 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
4388 Image Formats:
4389 ==============
4391 U-Boot is capable of booting (and performing other auxiliary operations on)
4392 images in two formats:
4394 New uImage format (FIT)
4395 -----------------------
4397 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
4398 to Flattened Device Tree). It allows the use of images with multiple
4399 components (several kernels, ramdisks, etc.), with contents protected by
4400 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
4403 Old uImage format
4404 -----------------
4406 Old image format is based on binary files which can be basically anything,
4407 preceded by a special header; see the definitions in include/image.h for
4408 details; basically, the header defines the following image properties:
4410 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
4411 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
4412 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
4413 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
4414 INTEGRITY).
4415 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
4416 IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
4417 Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
4418 * Compression Type (uncompressed, gzip, bzip2)
4419 * Load Address
4420 * Entry Point
4421 * Image Name
4422 * Image Timestamp
4424 The header is marked by a special Magic Number, and both the header
4425 and the data portions of the image are secured against corruption by
4426 CRC32 checksums.
4429 Linux Support:
4430 ==============
4432 Although U-Boot should support any OS or standalone application
4433 easily, the main focus has always been on Linux during the design of
4434 U-Boot.
4436 U-Boot includes many features that so far have been part of some
4437 special "boot loader" code within the Linux kernel. Also, any
4438 "initrd" images to be used are no longer part of one big Linux image;
4439 instead, kernel and "initrd" are separate images. This implementation
4440 serves several purposes:
4442 - the same features can be used for other OS or standalone
4443 applications (for instance: using compressed images to reduce the
4444 Flash memory footprint)
4446 - it becomes much easier to port new Linux kernel versions because
4447 lots of low-level, hardware dependent stuff are done by U-Boot
4449 - the same Linux kernel image can now be used with different "initrd"
4450 images; of course this also means that different kernel images can
4451 be run with the same "initrd". This makes testing easier (you don't
4452 have to build a new "zImage.initrd" Linux image when you just
4453 change a file in your "initrd"). Also, a field-upgrade of the
4454 software is easier now.
4457 Linux HOWTO:
4458 ============
4460 Porting Linux to U-Boot based systems:
4461 ---------------------------------------
4463 U-Boot cannot save you from doing all the necessary modifications to
4464 configure the Linux device drivers for use with your target hardware
4465 (no, we don't intend to provide a full virtual machine interface to
4466 Linux :-).
4468 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
4470 Just make sure your machine specific header file (for instance
4471 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
4472 Information structure as we define in include/asm-<arch>/u-boot.h,
4473 and make sure that your definition of IMAP_ADDR uses the same value
4474 as your U-Boot configuration in CONFIG_SYS_IMMR.
4477 Configuring the Linux kernel:
4478 -----------------------------
4480 No specific requirements for U-Boot. Make sure you have some root
4481 device (initial ramdisk, NFS) for your target system.
4484 Building a Linux Image:
4485 -----------------------
4487 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
4488 not used. If you use recent kernel source, a new build target
4489 "uImage" will exist which automatically builds an image usable by
4490 U-Boot. Most older kernels also have support for a "pImage" target,
4491 which was introduced for our predecessor project PPCBoot and uses a
4492 100% compatible format.
4494 Example:
4496 make TQM850L_config
4497 make oldconfig
4498 make dep
4499 make uImage
4501 The "uImage" build target uses a special tool (in 'tools/mkimage') to
4502 encapsulate a compressed Linux kernel image with header information,
4503 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
4505 * build a standard "vmlinux" kernel image (in ELF binary format):
4507 * convert the kernel into a raw binary image:
4509 ${CROSS_COMPILE}-objcopy -O binary \
4510 -R .note -R .comment \
4511 -S vmlinux linux.bin
4513 * compress the binary image:
4515 gzip -9 linux.bin
4517 * package compressed binary image for U-Boot:
4519 mkimage -A ppc -O linux -T kernel -C gzip \
4520 -a 0 -e 0 -n "Linux Kernel Image" \
4521 -d linux.bin.gz uImage
4524 The "mkimage" tool can also be used to create ramdisk images for use
4525 with U-Boot, either separated from the Linux kernel image, or
4526 combined into one file. "mkimage" encapsulates the images with a 64
4527 byte header containing information about target architecture,
4528 operating system, image type, compression method, entry points, time
4529 stamp, CRC32 checksums, etc.
4531 "mkimage" can be called in two ways: to verify existing images and
4532 print the header information, or to build new images.
4534 In the first form (with "-l" option) mkimage lists the information
4535 contained in the header of an existing U-Boot image; this includes
4536 checksum verification:
4538 tools/mkimage -l image
4539 -l ==> list image header information
4541 The second form (with "-d" option) is used to build a U-Boot image
4542 from a "data file" which is used as image payload:
4544 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
4545 -n name -d data_file image
4546 -A ==> set architecture to 'arch'
4547 -O ==> set operating system to 'os'
4548 -T ==> set image type to 'type'
4549 -C ==> set compression type 'comp'
4550 -a ==> set load address to 'addr' (hex)
4551 -e ==> set entry point to 'ep' (hex)
4552 -n ==> set image name to 'name'
4553 -d ==> use image data from 'datafile'
4555 Right now, all Linux kernels for PowerPC systems use the same load
4556 address (0x00000000), but the entry point address depends on the
4557 kernel version:
4559 - 2.2.x kernels have the entry point at 0x0000000C,
4560 - 2.3.x and later kernels have the entry point at 0x00000000.
4562 So a typical call to build a U-Boot image would read:
4564 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4565 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
4566 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
4567 > examples/uImage.TQM850L
4568 Image Name: 2.4.4 kernel for TQM850L
4569 Created: Wed Jul 19 02:34:59 2000
4570 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4571 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4572 Load Address: 0x00000000
4573 Entry Point: 0x00000000
4575 To verify the contents of the image (or check for corruption):
4577 -> tools/mkimage -l examples/uImage.TQM850L
4578 Image Name: 2.4.4 kernel for TQM850L
4579 Created: Wed Jul 19 02:34:59 2000
4580 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4581 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4582 Load Address: 0x00000000
4583 Entry Point: 0x00000000
4585 NOTE: for embedded systems where boot time is critical you can trade
4586 speed for memory and install an UNCOMPRESSED image instead: this
4587 needs more space in Flash, but boots much faster since it does not
4588 need to be uncompressed:
4590 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
4591 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4592 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
4593 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
4594 > examples/uImage.TQM850L-uncompressed
4595 Image Name: 2.4.4 kernel for TQM850L
4596 Created: Wed Jul 19 02:34:59 2000
4597 Image Type: PowerPC Linux Kernel Image (uncompressed)
4598 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
4599 Load Address: 0x00000000
4600 Entry Point: 0x00000000
4603 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
4604 when your kernel is intended to use an initial ramdisk:
4606 -> tools/mkimage -n 'Simple Ramdisk Image' \
4607 > -A ppc -O linux -T ramdisk -C gzip \
4608 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
4609 Image Name: Simple Ramdisk Image
4610 Created: Wed Jan 12 14:01:50 2000
4611 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4612 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
4613 Load Address: 0x00000000
4614 Entry Point: 0x00000000
4617 Installing a Linux Image:
4618 -------------------------
4620 To downloading a U-Boot image over the serial (console) interface,
4621 you must convert the image to S-Record format:
4623 objcopy -I binary -O srec examples/image examples/image.srec
4625 The 'objcopy' does not understand the information in the U-Boot
4626 image header, so the resulting S-Record file will be relative to
4627 address 0x00000000. To load it to a given address, you need to
4628 specify the target address as 'offset' parameter with the 'loads'
4629 command.
4631 Example: install the image to address 0x40100000 (which on the
4632 TQM8xxL is in the first Flash bank):
4634 => erase 40100000 401FFFFF
4636 .......... done
4637 Erased 8 sectors
4639 => loads 40100000
4640 ## Ready for S-Record download ...
4641 ~>examples/image.srec
4642 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
4643 ...
4644 15989 15990 15991 15992
4645 [file transfer complete]
4646 [connected]
4647 ## Start Addr = 0x00000000
4650 You can check the success of the download using the 'iminfo' command;
4651 this includes a checksum verification so you can be sure no data
4652 corruption happened:
4654 => imi 40100000
4656 ## Checking Image at 40100000 ...
4657 Image Name: 2.2.13 for initrd on TQM850L
4658 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4659 Data Size: 335725 Bytes = 327 kB = 0 MB
4660 Load Address: 00000000
4661 Entry Point: 0000000c
4662 Verifying Checksum ... OK
4665 Boot Linux:
4666 -----------
4668 The "bootm" command is used to boot an application that is stored in
4669 memory (RAM or Flash). In case of a Linux kernel image, the contents
4670 of the "bootargs" environment variable is passed to the kernel as
4671 parameters. You can check and modify this variable using the
4672 "printenv" and "setenv" commands:
4675 => printenv bootargs
4676 bootargs=root=/dev/ram
4678 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4680 => printenv bootargs
4681 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4683 => bootm 40020000
4684 ## Booting Linux kernel at 40020000 ...
4685 Image Name: 2.2.13 for NFS on TQM850L
4686 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4687 Data Size: 381681 Bytes = 372 kB = 0 MB
4688 Load Address: 00000000
4689 Entry Point: 0000000c
4690 Verifying Checksum ... OK
4691 Uncompressing Kernel Image ... OK
4692 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
4693 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4694 time_init: decrementer frequency = 187500000/60
4695 Calibrating delay loop... 49.77 BogoMIPS
4696 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
4697 ...
4699 If you want to boot a Linux kernel with initial RAM disk, you pass
4700 the memory addresses of both the kernel and the initrd image (PPBCOOT
4701 format!) to the "bootm" command:
4703 => imi 40100000 40200000
4705 ## Checking Image at 40100000 ...
4706 Image Name: 2.2.13 for initrd on TQM850L
4707 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4708 Data Size: 335725 Bytes = 327 kB = 0 MB
4709 Load Address: 00000000
4710 Entry Point: 0000000c
4711 Verifying Checksum ... OK
4713 ## Checking Image at 40200000 ...
4714 Image Name: Simple Ramdisk Image
4715 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4716 Data Size: 566530 Bytes = 553 kB = 0 MB
4717 Load Address: 00000000
4718 Entry Point: 00000000
4719 Verifying Checksum ... OK
4721 => bootm 40100000 40200000
4722 ## Booting Linux kernel at 40100000 ...
4723 Image Name: 2.2.13 for initrd on TQM850L
4724 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4725 Data Size: 335725 Bytes = 327 kB = 0 MB
4726 Load Address: 00000000
4727 Entry Point: 0000000c
4728 Verifying Checksum ... OK
4729 Uncompressing Kernel Image ... OK
4730 ## Loading RAMDisk Image at 40200000 ...
4731 Image Name: Simple Ramdisk Image
4732 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4733 Data Size: 566530 Bytes = 553 kB = 0 MB
4734 Load Address: 00000000
4735 Entry Point: 00000000
4736 Verifying Checksum ... OK
4737 Loading Ramdisk ... OK
4738 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
4739 Boot arguments: root=/dev/ram
4740 time_init: decrementer frequency = 187500000/60
4741 Calibrating delay loop... 49.77 BogoMIPS
4742 ...
4743 RAMDISK: Compressed image found at block 0
4744 VFS: Mounted root (ext2 filesystem).
4746 bash#
4748 Boot Linux and pass a flat device tree:
4749 -----------
4751 First, U-Boot must be compiled with the appropriate defines. See the section
4752 titled "Linux Kernel Interface" above for a more in depth explanation. The
4753 following is an example of how to start a kernel and pass an updated
4754 flat device tree:
4756 => print oftaddr
4757 oftaddr=0x300000
4758 => print oft
4759 oft=oftrees/mpc8540ads.dtb
4760 => tftp $oftaddr $oft
4761 Speed: 1000, full duplex
4762 Using TSEC0 device
4763 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
4764 Filename 'oftrees/mpc8540ads.dtb'.
4765 Load address: 0x300000
4766 Loading: #
4767 done
4768 Bytes transferred = 4106 (100a hex)
4769 => tftp $loadaddr $bootfile
4770 Speed: 1000, full duplex
4771 Using TSEC0 device
4772 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
4773 Filename 'uImage'.
4774 Load address: 0x200000
4775 Loading:############
4776 done
4777 Bytes transferred = 1029407 (fb51f hex)
4778 => print loadaddr
4779 loadaddr=200000
4780 => print oftaddr
4781 oftaddr=0x300000
4782 => bootm $loadaddr - $oftaddr
4783 ## Booting image at 00200000 ...
4784 Image Name: Linux-2.6.17-dirty
4785 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4786 Data Size: 1029343 Bytes = 1005.2 kB
4787 Load Address: 00000000
4788 Entry Point: 00000000
4789 Verifying Checksum ... OK
4790 Uncompressing Kernel Image ... OK
4791 Booting using flat device tree at 0x300000
4792 Using MPC85xx ADS machine description
4793 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
4794 [snip]
4797 More About U-Boot Image Types:
4798 ------------------------------
4800 U-Boot supports the following image types:
4802 "Standalone Programs" are directly runnable in the environment
4803 provided by U-Boot; it is expected that (if they behave
4804 well) you can continue to work in U-Boot after return from
4805 the Standalone Program.
4806 "OS Kernel Images" are usually images of some Embedded OS which
4807 will take over control completely. Usually these programs
4808 will install their own set of exception handlers, device
4809 drivers, set up the MMU, etc. - this means, that you cannot
4810 expect to re-enter U-Boot except by resetting the CPU.
4811 "RAMDisk Images" are more or less just data blocks, and their
4812 parameters (address, size) are passed to an OS kernel that is
4813 being started.
4814 "Multi-File Images" contain several images, typically an OS
4815 (Linux) kernel image and one or more data images like
4816 RAMDisks. This construct is useful for instance when you want
4817 to boot over the network using BOOTP etc., where the boot
4818 server provides just a single image file, but you want to get
4819 for instance an OS kernel and a RAMDisk image.
4821 "Multi-File Images" start with a list of image sizes, each
4822 image size (in bytes) specified by an "uint32_t" in network
4823 byte order. This list is terminated by an "(uint32_t)0".
4824 Immediately after the terminating 0 follow the images, one by
4825 one, all aligned on "uint32_t" boundaries (size rounded up to
4826 a multiple of 4 bytes).
4828 "Firmware Images" are binary images containing firmware (like
4829 U-Boot or FPGA images) which usually will be programmed to
4830 flash memory.
4832 "Script files" are command sequences that will be executed by
4833 U-Boot's command interpreter; this feature is especially
4834 useful when you configure U-Boot to use a real shell (hush)
4835 as command interpreter.
4837 Booting the Linux zImage:
4838 -------------------------
4840 On some platforms, it's possible to boot Linux zImage. This is done
4841 using the "bootz" command. The syntax of "bootz" command is the same
4842 as the syntax of "bootm" command.
4844 Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply
4845 kernel with raw initrd images. The syntax is slightly different, the
4846 address of the initrd must be augmented by it's size, in the following
4847 format: "<initrd addres>:<initrd size>".
4850 Standalone HOWTO:
4851 =================
4853 One of the features of U-Boot is that you can dynamically load and
4854 run "standalone" applications, which can use some resources of
4855 U-Boot like console I/O functions or interrupt services.
4857 Two simple examples are included with the sources:
4859 "Hello World" Demo:
4860 -------------------
4862 'examples/hello_world.c' contains a small "Hello World" Demo
4863 application; it is automatically compiled when you build U-Boot.
4864 It's configured to run at address 0x00040004, so you can play with it
4865 like that:
4867 => loads
4868 ## Ready for S-Record download ...
4869 ~>examples/hello_world.srec
4870 1 2 3 4 5 6 7 8 9 10 11 ...
4871 [file transfer complete]
4872 [connected]
4873 ## Start Addr = 0x00040004
4875 => go 40004 Hello World! This is a test.
4876 ## Starting application at 0x00040004 ...
4877 Hello World
4878 argc = 7
4879 argv[0] = "40004"
4880 argv[1] = "Hello"
4881 argv[2] = "World!"
4882 argv[3] = "This"
4883 argv[4] = "is"
4884 argv[5] = "a"
4885 argv[6] = "test."
4886 argv[7] = "<NULL>"
4887 Hit any key to exit ...
4889 ## Application terminated, rc = 0x0
4891 Another example, which demonstrates how to register a CPM interrupt
4892 handler with the U-Boot code, can be found in 'examples/timer.c'.
4893 Here, a CPM timer is set up to generate an interrupt every second.
4894 The interrupt service routine is trivial, just printing a '.'
4895 character, but this is just a demo program. The application can be
4896 controlled by the following keys:
4898 ? - print current values og the CPM Timer registers
4899 b - enable interrupts and start timer
4900 e - stop timer and disable interrupts
4901 q - quit application
4903 => loads
4904 ## Ready for S-Record download ...
4905 ~>examples/timer.srec
4906 1 2 3 4 5 6 7 8 9 10 11 ...
4907 [file transfer complete]
4908 [connected]
4909 ## Start Addr = 0x00040004
4911 => go 40004
4912 ## Starting application at 0x00040004 ...
4913 TIMERS=0xfff00980
4914 Using timer 1
4915 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
4917 Hit 'b':
4918 [q, b, e, ?] Set interval 1000000 us
4919 Enabling timer
4920 Hit '?':
4921 [q, b, e, ?] ........
4922 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
4923 Hit '?':
4924 [q, b, e, ?] .
4925 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
4926 Hit '?':
4927 [q, b, e, ?] .
4928 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
4929 Hit '?':
4930 [q, b, e, ?] .
4931 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
4932 Hit 'e':
4933 [q, b, e, ?] ...Stopping timer
4934 Hit 'q':
4935 [q, b, e, ?] ## Application terminated, rc = 0x0
4938 Minicom warning:
4939 ================
4941 Over time, many people have reported problems when trying to use the
4942 "minicom" terminal emulation program for serial download. I (wd)
4943 consider minicom to be broken, and recommend not to use it. Under
4944 Unix, I recommend to use C-Kermit for general purpose use (and
4945 especially for kermit binary protocol download ("loadb" command), and
4946 use "cu" for S-Record download ("loads" command). See
4947 http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
4948 for help with kermit.
4951 Nevertheless, if you absolutely want to use it try adding this
4952 configuration to your "File transfer protocols" section:
4954 Name Program Name U/D FullScr IO-Red. Multi
4955 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
4956 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
4959 NetBSD Notes:
4960 =============
4962 Starting at version 0.9.2, U-Boot supports NetBSD both as host
4963 (build U-Boot) and target system (boots NetBSD/mpc8xx).
4965 Building requires a cross environment; it is known to work on
4966 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
4967 need gmake since the Makefiles are not compatible with BSD make).
4968 Note that the cross-powerpc package does not install include files;
4969 attempting to build U-Boot will fail because <machine/ansi.h> is
4970 missing. This file has to be installed and patched manually:
4972 # cd /usr/pkg/cross/powerpc-netbsd/include
4973 # mkdir powerpc
4974 # ln -s powerpc machine
4975 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
4976 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
4978 Native builds *don't* work due to incompatibilities between native
4979 and U-Boot include files.
4981 Booting assumes that (the first part of) the image booted is a
4982 stage-2 loader which in turn loads and then invokes the kernel
4983 proper. Loader sources will eventually appear in the NetBSD source
4984 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
4985 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
4988 Implementation Internals:
4989 =========================
4991 The following is not intended to be a complete description of every
4992 implementation detail. However, it should help to understand the
4993 inner workings of U-Boot and make it easier to port it to custom
4994 hardware.
4997 Initial Stack, Global Data:
4998 ---------------------------
5000 The implementation of U-Boot is complicated by the fact that U-Boot
5001 starts running out of ROM (flash memory), usually without access to
5002 system RAM (because the memory controller is not initialized yet).
5003 This means that we don't have writable Data or BSS segments, and BSS
5004 is not initialized as zero. To be able to get a C environment working
5005 at all, we have to allocate at least a minimal stack. Implementation
5006 options for this are defined and restricted by the CPU used: Some CPU
5007 models provide on-chip memory (like the IMMR area on MPC8xx and
5008 MPC826x processors), on others (parts of) the data cache can be
5009 locked as (mis-) used as memory, etc.
5011 Chris Hallinan posted a good summary of these issues to the
5012 U-Boot mailing list:
5014 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
5015 From: "Chris Hallinan" <clh@net1plus.com>
5016 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
5017 ...
5019 Correct me if I'm wrong, folks, but the way I understand it
5020 is this: Using DCACHE as initial RAM for Stack, etc, does not
5021 require any physical RAM backing up the cache. The cleverness
5022 is that the cache is being used as a temporary supply of
5023 necessary storage before the SDRAM controller is setup. It's
5024 beyond the scope of this list to explain the details, but you
5025 can see how this works by studying the cache architecture and
5026 operation in the architecture and processor-specific manuals.
5028 OCM is On Chip Memory, which I believe the 405GP has 4K. It
5029 is another option for the system designer to use as an
5030 initial stack/RAM area prior to SDRAM being available. Either
5031 option should work for you. Using CS 4 should be fine if your
5032 board designers haven't used it for something that would
5033 cause you grief during the initial boot! It is frequently not
5034 used.
5036 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
5037 with your processor/board/system design. The default value
5038 you will find in any recent u-boot distribution in
5039 walnut.h should work for you. I'd set it to a value larger
5040 than your SDRAM module. If you have a 64MB SDRAM module, set
5041 it above 400_0000. Just make sure your board has no resources
5042 that are supposed to respond to that address! That code in
5043 start.S has been around a while and should work as is when
5044 you get the config right.
5046 -Chris Hallinan
5047 DS4.COM, Inc.
5049 It is essential to remember this, since it has some impact on the C
5050 code for the initialization procedures:
5052 * Initialized global data (data segment) is read-only. Do not attempt
5053 to write it.
5055 * Do not use any uninitialized global data (or implicitely initialized
5056 as zero data - BSS segment) at all - this is undefined, initiali-
5057 zation is performed later (when relocating to RAM).
5059 * Stack space is very limited. Avoid big data buffers or things like
5060 that.
5062 Having only the stack as writable memory limits means we cannot use
5063 normal global data to share information beween the code. But it
5064 turned out that the implementation of U-Boot can be greatly
5065 simplified by making a global data structure (gd_t) available to all
5066 functions. We could pass a pointer to this data as argument to _all_
5067 functions, but this would bloat the code. Instead we use a feature of
5068 the GCC compiler (Global Register Variables) to share the data: we
5069 place a pointer (gd) to the global data into a register which we
5070 reserve for this purpose.
5072 When choosing a register for such a purpose we are restricted by the
5073 relevant (E)ABI specifications for the current architecture, and by
5074 GCC's implementation.
5076 For PowerPC, the following registers have specific use:
5077 R1: stack pointer
5078 R2: reserved for system use
5079 R3-R4: parameter passing and return values
5080 R5-R10: parameter passing
5081 R13: small data area pointer
5082 R30: GOT pointer
5083 R31: frame pointer
5085 (U-Boot also uses R12 as internal GOT pointer. r12
5086 is a volatile register so r12 needs to be reset when
5087 going back and forth between asm and C)
5089 ==> U-Boot will use R2 to hold a pointer to the global data
5091 Note: on PPC, we could use a static initializer (since the
5092 address of the global data structure is known at compile time),
5093 but it turned out that reserving a register results in somewhat
5094 smaller code - although the code savings are not that big (on
5095 average for all boards 752 bytes for the whole U-Boot image,
5096 624 text + 127 data).
5098 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
5099 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
5101 ==> U-Boot will use P3 to hold a pointer to the global data
5103 On ARM, the following registers are used:
5105 R0: function argument word/integer result
5106 R1-R3: function argument word
5107 R9: GOT pointer
5108 R10: stack limit (used only if stack checking if enabled)
5109 R11: argument (frame) pointer
5110 R12: temporary workspace
5111 R13: stack pointer
5112 R14: link register
5113 R15: program counter
5115 ==> U-Boot will use R8 to hold a pointer to the global data
5117 On Nios II, the ABI is documented here:
5118 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
5120 ==> U-Boot will use gp to hold a pointer to the global data
5122 Note: on Nios II, we give "-G0" option to gcc and don't use gp
5123 to access small data sections, so gp is free.
5125 On NDS32, the following registers are used:
5127 R0-R1: argument/return
5128 R2-R5: argument
5129 R15: temporary register for assembler
5130 R16: trampoline register
5131 R28: frame pointer (FP)
5132 R29: global pointer (GP)
5133 R30: link register (LP)
5134 R31: stack pointer (SP)
5135 PC: program counter (PC)
5137 ==> U-Boot will use R10 to hold a pointer to the global data
5139 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
5140 or current versions of GCC may "optimize" the code too much.
5142 Memory Management:
5143 ------------------
5145 U-Boot runs in system state and uses physical addresses, i.e. the
5146 MMU is not used either for address mapping nor for memory protection.
5148 The available memory is mapped to fixed addresses using the memory
5149 controller. In this process, a contiguous block is formed for each
5150 memory type (Flash, SDRAM, SRAM), even when it consists of several
5151 physical memory banks.
5153 U-Boot is installed in the first 128 kB of the first Flash bank (on
5154 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
5155 booting and sizing and initializing DRAM, the code relocates itself
5156 to the upper end of DRAM. Immediately below the U-Boot code some
5157 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
5158 configuration setting]. Below that, a structure with global Board
5159 Info data is placed, followed by the stack (growing downward).
5161 Additionally, some exception handler code is copied to the low 8 kB
5162 of DRAM (0x00000000 ... 0x00001FFF).
5164 So a typical memory configuration with 16 MB of DRAM could look like
5165 this:
5167 0x0000 0000 Exception Vector code
5168 :
5169 0x0000 1FFF
5170 0x0000 2000 Free for Application Use
5171 :
5172 :
5174 :
5175 :
5176 0x00FB FF20 Monitor Stack (Growing downward)
5177 0x00FB FFAC Board Info Data and permanent copy of global data
5178 0x00FC 0000 Malloc Arena
5179 :
5180 0x00FD FFFF
5181 0x00FE 0000 RAM Copy of Monitor Code
5182 ... eventually: LCD or video framebuffer
5183 ... eventually: pRAM (Protected RAM - unchanged by reset)
5184 0x00FF FFFF [End of RAM]
5187 System Initialization:
5188 ----------------------
5190 In the reset configuration, U-Boot starts at the reset entry point
5191 (on most PowerPC systems at address 0x00000100). Because of the reset
5192 configuration for CS0# this is a mirror of the onboard Flash memory.
5193 To be able to re-map memory U-Boot then jumps to its link address.
5194 To be able to implement the initialization code in C, a (small!)
5195 initial stack is set up in the internal Dual Ported RAM (in case CPUs
5196 which provide such a feature like MPC8xx or MPC8260), or in a locked
5197 part of the data cache. After that, U-Boot initializes the CPU core,
5198 the caches and the SIU.
5200 Next, all (potentially) available memory banks are mapped using a
5201 preliminary mapping. For example, we put them on 512 MB boundaries
5202 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
5203 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
5204 programmed for SDRAM access. Using the temporary configuration, a
5205 simple memory test is run that determines the size of the SDRAM
5206 banks.
5208 When there is more than one SDRAM bank, and the banks are of
5209 different size, the largest is mapped first. For equal size, the first
5210 bank (CS2#) is mapped first. The first mapping is always for address
5211 0x00000000, with any additional banks following immediately to create
5212 contiguous memory starting from 0.
5214 Then, the monitor installs itself at the upper end of the SDRAM area
5215 and allocates memory for use by malloc() and for the global Board
5216 Info data; also, the exception vector code is copied to the low RAM
5217 pages, and the final stack is set up.
5219 Only after this relocation will you have a "normal" C environment;
5220 until that you are restricted in several ways, mostly because you are
5221 running from ROM, and because the code will have to be relocated to a
5222 new address in RAM.
5225 U-Boot Porting Guide:
5226 ----------------------
5228 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
5229 list, October 2002]
5232 int main(int argc, char *argv[])
5233 {
5234 sighandler_t no_more_time;
5236 signal(SIGALRM, no_more_time);
5237 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
5239 if (available_money > available_manpower) {
5240 Pay consultant to port U-Boot;
5241 return 0;
5242 }
5244 Download latest U-Boot source;
5246 Subscribe to u-boot mailing list;
5248 if (clueless)
5249 email("Hi, I am new to U-Boot, how do I get started?");
5251 while (learning) {
5252 Read the README file in the top level directory;
5253 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
5254 Read applicable doc/*.README;
5255 Read the source, Luke;
5256 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
5257 }
5259 if (available_money > toLocalCurrency ($2500))
5260 Buy a BDI3000;
5261 else
5262 Add a lot of aggravation and time;
5264 if (a similar board exists) { /* hopefully... */
5265 cp -a board/<similar> board/<myboard>
5266 cp include/configs/<similar>.h include/configs/<myboard>.h
5267 } else {
5268 Create your own board support subdirectory;
5269 Create your own board include/configs/<myboard>.h file;
5270 }
5271 Edit new board/<myboard> files
5272 Edit new include/configs/<myboard>.h
5274 while (!accepted) {
5275 while (!running) {
5276 do {
5277 Add / modify source code;
5278 } until (compiles);
5279 Debug;
5280 if (clueless)
5281 email("Hi, I am having problems...");
5282 }
5283 Send patch file to the U-Boot email list;
5284 if (reasonable critiques)
5285 Incorporate improvements from email list code review;
5286 else
5287 Defend code as written;
5288 }
5290 return 0;
5291 }
5293 void no_more_time (int sig)
5294 {
5295 hire_a_guru();
5296 }
5299 Coding Standards:
5300 -----------------
5302 All contributions to U-Boot should conform to the Linux kernel
5303 coding style; see the file "Documentation/CodingStyle" and the script
5304 "scripts/Lindent" in your Linux kernel source directory.
5306 Source files originating from a different project (for example the
5307 MTD subsystem) are generally exempt from these guidelines and are not
5308 reformated to ease subsequent migration to newer versions of those
5309 sources.
5311 Please note that U-Boot is implemented in C (and to some small parts in
5312 Assembler); no C++ is used, so please do not use C++ style comments (//)
5313 in your code.
5315 Please also stick to the following formatting rules:
5316 - remove any trailing white space
5317 - use TAB characters for indentation and vertical alignment, not spaces
5318 - make sure NOT to use DOS '\r\n' line feeds
5319 - do not add more than 2 consecutive empty lines to source files
5320 - do not add trailing empty lines to source files
5322 Submissions which do not conform to the standards may be returned
5323 with a request to reformat the changes.
5326 Submitting Patches:
5327 -------------------
5329 Since the number of patches for U-Boot is growing, we need to
5330 establish some rules. Submissions which do not conform to these rules
5331 may be rejected, even when they contain important and valuable stuff.
5333 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
5335 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
5336 see http://lists.denx.de/mailman/listinfo/u-boot
5338 When you send a patch, please include the following information with
5339 it:
5341 * For bug fixes: a description of the bug and how your patch fixes
5342 this bug. Please try to include a way of demonstrating that the
5343 patch actually fixes something.
5345 * For new features: a description of the feature and your
5346 implementation.
5348 * A CHANGELOG entry as plaintext (separate from the patch)
5350 * For major contributions, your entry to the CREDITS file
5352 * When you add support for a new board, don't forget to add this
5353 board to the MAINTAINERS file, too.
5355 * If your patch adds new configuration options, don't forget to
5356 document these in the README file.
5358 * The patch itself. If you are using git (which is *strongly*
5359 recommended) you can easily generate the patch using the
5360 "git format-patch". If you then use "git send-email" to send it to
5361 the U-Boot mailing list, you will avoid most of the common problems
5362 with some other mail clients.
5364 If you cannot use git, use "diff -purN OLD NEW". If your version of
5365 diff does not support these options, then get the latest version of
5366 GNU diff.
5368 The current directory when running this command shall be the parent
5369 directory of the U-Boot source tree (i. e. please make sure that
5370 your patch includes sufficient directory information for the
5371 affected files).
5373 We prefer patches as plain text. MIME attachments are discouraged,
5374 and compressed attachments must not be used.
5376 * If one logical set of modifications affects or creates several
5377 files, all these changes shall be submitted in a SINGLE patch file.
5379 * Changesets that contain different, unrelated modifications shall be
5380 submitted as SEPARATE patches, one patch per changeset.
5383 Notes:
5385 * Before sending the patch, run the MAKEALL script on your patched
5386 source tree and make sure that no errors or warnings are reported
5387 for any of the boards.
5389 * Keep your modifications to the necessary minimum: A patch
5390 containing several unrelated changes or arbitrary reformats will be
5391 returned with a request to re-formatting / split it.
5393 * If you modify existing code, make sure that your new code does not
5394 add to the memory footprint of the code ;-) Small is beautiful!
5395 When adding new features, these should compile conditionally only
5396 (using #ifdef), and the resulting code with the new feature
5397 disabled must not need more memory than the old code without your
5398 modification.
5400 * Remember that there is a size limit of 100 kB per message on the
5401 u-boot mailing list. Bigger patches will be moderated. If they are
5402 reasonable and not too big, they will be acknowledged. But patches
5403 bigger than the size limit should be avoided.