4 years agoMerged TI feature ti_linux_base_rt into ti-rt-linux-4.19.y ti-rt-linux-4.19.y-next-20190918 ti-rt-linux-4.19.y-next-20190919 ti-rt-linux-4.19.y-next-20190920
Merged TI feature ti_linux_base_rt into ti-rt-linux-4.19.y
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel:
crypto: sa2ul: Add sha512 HW crypto support
crypto: sa2ul: Do spin_lock_init on scid_lock
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel:
crypto: sa2ul: Add sha512 HW crypto support
crypto: sa2ul: Do spin_lock_init on scid_lock
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
Merged TI feature platform_base into ti-linux-4.19.y
TI-Feature: platform_base
TI-Branch: platform-ti-linux-4.19.y
* 'platform-ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpublicdom/platform:
crypto: sa2ul: Add sha512 HW crypto support
crypto: sa2ul: Do spin_lock_init on scid_lock
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
TI-Feature: platform_base
TI-Branch: platform-ti-linux-4.19.y
* 'platform-ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpublicdom/platform:
crypto: sa2ul: Add sha512 HW crypto support
crypto: sa2ul: Do spin_lock_init on scid_lock
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
Merged TI feature ti_linux_base_rt into ti-rt-linux-4.19.y
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel: (190 commits)
Linux 4.19.73
vhost: make sure log_num < in_num
powerpc/tm: Fix restoring FP/VMX facility incorrectly on interrupts
powerpc/tm: Remove msr_tm_active()
PCI: Reset both NVIDIA GPU and HDA in ThinkPad P50 workaround
ext4: unsigned int compared against zero
ext4: fix block validity checks for journal inodes using indirect blocks
ext4: don't perform block validity checks on the journal inode
drm/atomic_helper: Allow DPMS On<->Off changes for unregistered connectors
virtio/s390: fix race on airq_areas[]
drm/i915: Make sure cdclk is high enough for DP audio on VLV/CHV
bcache: fix race in btree_flush_write()
bcache: add comments for mutex_lock(&b->write_lock)
bcache: only clear BTREE_NODE_dirty bit when it is set
NFSv4: Fix delegation state recovery
iio: adc: gyroadc: fix uninitialized return code
mm/migrate.c: initialize pud_entry in migrate_vma()
i2c: at91: fix clk_offset for sama5d2
i2c: at91: disable TXRDY interrupt after sending data
gpio: don't WARN() on NULL descs if gpiolib is disabled
...
Signed-off-by: Dan Murphy <dmurphy@ti.com>
# Conflicts:
# fs/nfs/delegation.c
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel: (190 commits)
Linux 4.19.73
vhost: make sure log_num < in_num
powerpc/tm: Fix restoring FP/VMX facility incorrectly on interrupts
powerpc/tm: Remove msr_tm_active()
PCI: Reset both NVIDIA GPU and HDA in ThinkPad P50 workaround
ext4: unsigned int compared against zero
ext4: fix block validity checks for journal inodes using indirect blocks
ext4: don't perform block validity checks on the journal inode
drm/atomic_helper: Allow DPMS On<->Off changes for unregistered connectors
virtio/s390: fix race on airq_areas[]
drm/i915: Make sure cdclk is high enough for DP audio on VLV/CHV
bcache: fix race in btree_flush_write()
bcache: add comments for mutex_lock(&b->write_lock)
bcache: only clear BTREE_NODE_dirty bit when it is set
NFSv4: Fix delegation state recovery
iio: adc: gyroadc: fix uninitialized return code
mm/migrate.c: initialize pud_entry in migrate_vma()
i2c: at91: fix clk_offset for sama5d2
i2c: at91: disable TXRDY interrupt after sending data
gpio: don't WARN() on NULL descs if gpiolib is disabled
...
Signed-off-by: Dan Murphy <dmurphy@ti.com>
# Conflicts:
# fs/nfs/delegation.c
Merged TI feature linux_rt-4-19 into ti-rt-linux-4.19.y
TI-Feature: linux_rt-4-19
TI-Branch: v4.19-rt
* 'v4.19-rt' of https://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-stable-rt: (1081 commits)
Linux 4.19.72-rt25
Linux 4.19.72
Revert "x86/apic: Include the LDR when clearing out APIC registers"
libceph: allow ceph_buffer_put() to receive a NULL ceph_buffer
x86/boot/compressed/64: Fix missing initialization in find_trampoline_placement()
KVM: arm/arm64: VGIC: Properly initialise private IRQ affinity
afs: Fix leak in afs_lookup_cell_rcu()
KVM: arm/arm64: Only skip MMIO insn once
ceph: fix buffer free while holding i_ceph_lock in fill_inode()
ceph: fix buffer free while holding i_ceph_lock in __ceph_build_xattrs_blob()
ceph: fix buffer free while holding i_ceph_lock in __ceph_setxattr()
selftests/kvm: make platform_info_test pass on AMD
selftests: kvm: fix state save/load on processors without XSAVE
infiniband: hfi1: fix memory leaks
infiniband: hfi1: fix a memory leak bug
IB/mlx4: Fix memory leaks
nvme-multipath: fix possible I/O hang when paths are updated
Tools: hv: kvp: eliminate 'may be used uninitialized' warning
Input: hyperv-keyboard: Use in-place iterator API in the channel callback
x86/boot/compressed/64: Fix boot on machines with broken E820 table
...
Signed-off-by: Dan Murphy <dmurphy@ti.com>
# Conflicts:
# drivers/gpu/drm/bridge/sii902x.c
# sound/soc/ti/davinci-mcasp.c
TI-Feature: linux_rt-4-19
TI-Branch: v4.19-rt
* 'v4.19-rt' of https://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-stable-rt: (1081 commits)
Linux 4.19.72-rt25
Linux 4.19.72
Revert "x86/apic: Include the LDR when clearing out APIC registers"
libceph: allow ceph_buffer_put() to receive a NULL ceph_buffer
x86/boot/compressed/64: Fix missing initialization in find_trampoline_placement()
KVM: arm/arm64: VGIC: Properly initialise private IRQ affinity
afs: Fix leak in afs_lookup_cell_rcu()
KVM: arm/arm64: Only skip MMIO insn once
ceph: fix buffer free while holding i_ceph_lock in fill_inode()
ceph: fix buffer free while holding i_ceph_lock in __ceph_build_xattrs_blob()
ceph: fix buffer free while holding i_ceph_lock in __ceph_setxattr()
selftests/kvm: make platform_info_test pass on AMD
selftests: kvm: fix state save/load on processors without XSAVE
infiniband: hfi1: fix memory leaks
infiniband: hfi1: fix a memory leak bug
IB/mlx4: Fix memory leaks
nvme-multipath: fix possible I/O hang when paths are updated
Tools: hv: kvp: eliminate 'may be used uninitialized' warning
Input: hyperv-keyboard: Use in-place iterator API in the channel callback
x86/boot/compressed/64: Fix boot on machines with broken E820 table
...
Signed-off-by: Dan Murphy <dmurphy@ti.com>
# Conflicts:
# drivers/gpu/drm/bridge/sii902x.c
# sound/soc/ti/davinci-mcasp.c
Merge branch 'linux-4.19.y' of http://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable into ti-linux-4.19.y
* 'linux-4.19.y' of http://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable: (1270 commits)
Linux 4.19.73
vhost: make sure log_num < in_num
powerpc/tm: Fix restoring FP/VMX facility incorrectly on interrupts
powerpc/tm: Remove msr_tm_active()
PCI: Reset both NVIDIA GPU and HDA in ThinkPad P50 workaround
ext4: unsigned int compared against zero
ext4: fix block validity checks for journal inodes using indirect blocks
ext4: don't perform block validity checks on the journal inode
drm/atomic_helper: Allow DPMS On<->Off changes for unregistered connectors
virtio/s390: fix race on airq_areas[]
drm/i915: Make sure cdclk is high enough for DP audio on VLV/CHV
bcache: fix race in btree_flush_write()
bcache: add comments for mutex_lock(&b->write_lock)
bcache: only clear BTREE_NODE_dirty bit when it is set
NFSv4: Fix delegation state recovery
iio: adc: gyroadc: fix uninitialized return code
mm/migrate.c: initialize pud_entry in migrate_vma()
i2c: at91: fix clk_offset for sama5d2
i2c: at91: disable TXRDY interrupt after sending data
gpio: don't WARN() on NULL descs if gpiolib is disabled
...
Signed-off-by: Dan Murphy <dmurphy@ti.com>
# Conflicts:
# drivers/gpu/drm/bridge/sii902x.c
# sound/soc/ti/davinci-mcasp.c
* 'linux-4.19.y' of http://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable: (1270 commits)
Linux 4.19.73
vhost: make sure log_num < in_num
powerpc/tm: Fix restoring FP/VMX facility incorrectly on interrupts
powerpc/tm: Remove msr_tm_active()
PCI: Reset both NVIDIA GPU and HDA in ThinkPad P50 workaround
ext4: unsigned int compared against zero
ext4: fix block validity checks for journal inodes using indirect blocks
ext4: don't perform block validity checks on the journal inode
drm/atomic_helper: Allow DPMS On<->Off changes for unregistered connectors
virtio/s390: fix race on airq_areas[]
drm/i915: Make sure cdclk is high enough for DP audio on VLV/CHV
bcache: fix race in btree_flush_write()
bcache: add comments for mutex_lock(&b->write_lock)
bcache: only clear BTREE_NODE_dirty bit when it is set
NFSv4: Fix delegation state recovery
iio: adc: gyroadc: fix uninitialized return code
mm/migrate.c: initialize pud_entry in migrate_vma()
i2c: at91: fix clk_offset for sama5d2
i2c: at91: disable TXRDY interrupt after sending data
gpio: don't WARN() on NULL descs if gpiolib is disabled
...
Signed-off-by: Dan Murphy <dmurphy@ti.com>
# Conflicts:
# drivers/gpu/drm/bridge/sii902x.c
# sound/soc/ti/davinci-mcasp.c
Merged TI feature ti_linux_base_rt into ti-rt-linux-4.19.y
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel:
rpmsg-kdrv: eth-switch: use tabs instead of spaces for indentation
arm64: dts: ti: k3-j721e-main: Add Support for UHS modes
arm64: dts: k3-j721e-common-proc-board: Add vqmmc supply for pm2 SoM
arm64: dts: ti: k3-j721e-proc-board-tps65917: Sync mmc1 pinmux
arm64: dts: ti: k3-j721e-main: Update otap-del-sel values
mmc: sdhci_am654: Always set otap_del_sel for 4 bit IP
arm64: dts: ti: k3-j721e-main: Add ti,clkbuf-sel property
mmc: sdhci_am654: Add support for clkbuf_sel property
dt-bindings: mmc: sdhci-am654: Add documentation for clkbuf-sel property
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel:
rpmsg-kdrv: eth-switch: use tabs instead of spaces for indentation
arm64: dts: ti: k3-j721e-main: Add Support for UHS modes
arm64: dts: k3-j721e-common-proc-board: Add vqmmc supply for pm2 SoM
arm64: dts: ti: k3-j721e-proc-board-tps65917: Sync mmc1 pinmux
arm64: dts: ti: k3-j721e-main: Update otap-del-sel values
mmc: sdhci_am654: Always set otap_del_sel for 4 bit IP
arm64: dts: ti: k3-j721e-main: Add ti,clkbuf-sel property
mmc: sdhci_am654: Add support for clkbuf_sel property
dt-bindings: mmc: sdhci-am654: Add documentation for clkbuf-sel property
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
Merged TI feature connectivity into ti-linux-4.19.y
TI-Feature: connectivity
TI-Branch: connectivity-ti-linux-4.19.y
* 'connectivity-ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpublicdom/connectivity:
rpmsg-kdrv: eth-switch: use tabs instead of spaces for indentation
arm64: dts: ti: k3-j721e-main: Add Support for UHS modes
arm64: dts: k3-j721e-common-proc-board: Add vqmmc supply for pm2 SoM
arm64: dts: ti: k3-j721e-proc-board-tps65917: Sync mmc1 pinmux
arm64: dts: ti: k3-j721e-main: Update otap-del-sel values
mmc: sdhci_am654: Always set otap_del_sel for 4 bit IP
arm64: dts: ti: k3-j721e-main: Add ti,clkbuf-sel property
mmc: sdhci_am654: Add support for clkbuf_sel property
dt-bindings: mmc: sdhci-am654: Add documentation for clkbuf-sel property
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
TI-Feature: connectivity
TI-Branch: connectivity-ti-linux-4.19.y
* 'connectivity-ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpublicdom/connectivity:
rpmsg-kdrv: eth-switch: use tabs instead of spaces for indentation
arm64: dts: ti: k3-j721e-main: Add Support for UHS modes
arm64: dts: k3-j721e-common-proc-board: Add vqmmc supply for pm2 SoM
arm64: dts: ti: k3-j721e-proc-board-tps65917: Sync mmc1 pinmux
arm64: dts: ti: k3-j721e-main: Update otap-del-sel values
mmc: sdhci_am654: Always set otap_del_sel for 4 bit IP
arm64: dts: ti: k3-j721e-main: Add ti,clkbuf-sel property
mmc: sdhci_am654: Add support for clkbuf_sel property
dt-bindings: mmc: sdhci-am654: Add documentation for clkbuf-sel property
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
crypto: sa2ul: Add sha512 HW crypto support
Add sha512 HW crypto support.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Add sha512 HW crypto support.
Signed-off-by: Keerthy <j-keerthy@ti.com>
crypto: sa2ul: Do spin_lock_init on scid_lock
It might work w/o spin_lock_init, but it is not a good practice for sure.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
It might work w/o spin_lock_init, but it is not a good practice for sure.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
rpmsg-kdrv: eth-switch: use tabs instead of spaces for indentation
Fix this checkpatch error:
ERROR: code indent should use tabs where possible
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Fix this checkpatch error:
ERROR: code indent should use tabs where possible
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
arm64: dts: ti: k3-j721e-main: Add Support for UHS modes
Enable Support for SD UHS modes other than SDR104 mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Enable Support for SD UHS modes other than SDR104 mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
arm64: dts: k3-j721e-common-proc-board: Add vqmmc supply for pm2 SoM
pm2 SoM contains a gpio to switch the SD card from 3.3V to 1.8V instead
of the being connected to the regulator. Model this as a gpio regulator
and add the vqmmc-supply to sdhci1 to support UHS modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
pm2 SoM contains a gpio to switch the SD card from 3.3V to 1.8V instead
of the being connected to the regulator. Model this as a gpio regulator
and add the vqmmc-supply to sdhci1 to support UHS modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
arm64: dts: ti: k3-j721e-proc-board-tps65917: Sync mmc1 pinmux
Update the MMC1 pinmux to match the output of the latest pinmux tool.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Update the MMC1 pinmux to match the output of the latest pinmux tool.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
arm64: dts: ti: k3-j721e-main: Update otap-del-sel values
Update otap-del-sel values to match the latest RIOT values.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Update otap-del-sel values to match the latest RIOT values.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
mmc: sdhci_am654: Always set otap_del_sel for 4 bit IP
In the newest RIOT document, otap_del_ena is 0x1 for all speed modes.
Update the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In the newest RIOT document, otap_del_ena is 0x1 for all speed modes.
Update the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
arm64: dts: ti: k3-j721e-main: Add ti,clkbuf-sel property
Add ti,clkbuf-sel property to the two 4 bit IP instances to match with
the latest RIOT values.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add ti,clkbuf-sel property to the two 4 bit IP instances to match with
the latest RIOT values.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
mmc: sdhci_am654: Add support for clkbuf_sel property
Add support for writing new clkbuf_sel property for the J721e 4 bit IP.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for writing new clkbuf_sel property for the J721e 4 bit IP.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
dt-bindings: mmc: sdhci-am654: Add documentation for clkbuf-sel property
Add Documentation for the optional ti,clkbuf-sel property.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add Documentation for the optional ti,clkbuf-sel property.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Linux 4.19.72-rt25
4 years agoMerged TI feature ti_linux_base_rt into ti-rt-linux-4.19.y ti-rt-linux-4.19.y-next-20190917
Merged TI feature ti_linux_base_rt into ti-rt-linux-4.19.y
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel:
usb:cdns3: Fix for CV CH9 running with g_zero driver.
arm64: dts: ti: k3-j721e-main: Remove duplicate power-domain
arm64: dts: add k3-am654-evm-prupwm.dtso
pwm: add pruss iep-based pwm driver
pwm: core: populate the sysfs device into pwmchip
dt-bindings: pwm: add binding documentation for TI PRUSS PWM
ti_config_fragments/connectivity.cfg: enable j721e-cpsw-virt-mac driver
arm64: dts: ti: k3-j721e-common-proc-board: disable main_uart2 for eth switch fw
arm64: dts: ti: k3-j721e-common-proc-board: add virt cpsw9g mac node
net: ethernet: ti: introduce j721e virt cpsw-nuss mac driver
dt-bindings: net: Add binding for ti,j721e-cpsw-virt-mac device
rpmsg-kdrv: add support for remote eth device
dmaengine: ti: k3-navss-udma: add support for remote/virt udma channels
dmaengine: ti: k3-navss-udma: drop need_tisci_free
dmaengine: ti: k3-navss-udma: fix k3_nav_udmax_release_rx_flow()
dmaengine: ti: k3-navss-udma: fix gp rflow freeing in k3_nav_udmax_release_rx_chn()
dmaengine: ti: k3-navss-udma: fix access to udmax in k3_nav_udmax_release_rx_chn()
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel:
usb:cdns3: Fix for CV CH9 running with g_zero driver.
arm64: dts: ti: k3-j721e-main: Remove duplicate power-domain
arm64: dts: add k3-am654-evm-prupwm.dtso
pwm: add pruss iep-based pwm driver
pwm: core: populate the sysfs device into pwmchip
dt-bindings: pwm: add binding documentation for TI PRUSS PWM
ti_config_fragments/connectivity.cfg: enable j721e-cpsw-virt-mac driver
arm64: dts: ti: k3-j721e-common-proc-board: disable main_uart2 for eth switch fw
arm64: dts: ti: k3-j721e-common-proc-board: add virt cpsw9g mac node
net: ethernet: ti: introduce j721e virt cpsw-nuss mac driver
dt-bindings: net: Add binding for ti,j721e-cpsw-virt-mac device
rpmsg-kdrv: add support for remote eth device
dmaengine: ti: k3-navss-udma: add support for remote/virt udma channels
dmaengine: ti: k3-navss-udma: drop need_tisci_free
dmaengine: ti: k3-navss-udma: fix k3_nav_udmax_release_rx_flow()
dmaengine: ti: k3-navss-udma: fix gp rflow freeing in k3_nav_udmax_release_rx_chn()
dmaengine: ti: k3-navss-udma: fix access to udmax in k3_nav_udmax_release_rx_chn()
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
Merged TI feature connectivity into ti-linux-4.19.y
TI-Feature: connectivity
TI-Branch: connectivity-ti-linux-4.19.y
* 'connectivity-ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpublicdom/connectivity:
usb:cdns3: Fix for CV CH9 running with g_zero driver.
arm64: dts: ti: k3-j721e-main: Remove duplicate power-domain
arm64: dts: add k3-am654-evm-prupwm.dtso
pwm: add pruss iep-based pwm driver
pwm: core: populate the sysfs device into pwmchip
dt-bindings: pwm: add binding documentation for TI PRUSS PWM
ti_config_fragments/connectivity.cfg: enable j721e-cpsw-virt-mac driver
arm64: dts: ti: k3-j721e-common-proc-board: disable main_uart2 for eth switch fw
arm64: dts: ti: k3-j721e-common-proc-board: add virt cpsw9g mac node
net: ethernet: ti: introduce j721e virt cpsw-nuss mac driver
dt-bindings: net: Add binding for ti,j721e-cpsw-virt-mac device
rpmsg-kdrv: add support for remote eth device
dmaengine: ti: k3-navss-udma: add support for remote/virt udma channels
dmaengine: ti: k3-navss-udma: drop need_tisci_free
dmaengine: ti: k3-navss-udma: fix k3_nav_udmax_release_rx_flow()
dmaengine: ti: k3-navss-udma: fix gp rflow freeing in k3_nav_udmax_release_rx_chn()
dmaengine: ti: k3-navss-udma: fix access to udmax in k3_nav_udmax_release_rx_chn()
Signed-off-by: Dan Murphy <dmurphy@ti.com>
TI-Feature: connectivity
TI-Branch: connectivity-ti-linux-4.19.y
* 'connectivity-ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpublicdom/connectivity:
usb:cdns3: Fix for CV CH9 running with g_zero driver.
arm64: dts: ti: k3-j721e-main: Remove duplicate power-domain
arm64: dts: add k3-am654-evm-prupwm.dtso
pwm: add pruss iep-based pwm driver
pwm: core: populate the sysfs device into pwmchip
dt-bindings: pwm: add binding documentation for TI PRUSS PWM
ti_config_fragments/connectivity.cfg: enable j721e-cpsw-virt-mac driver
arm64: dts: ti: k3-j721e-common-proc-board: disable main_uart2 for eth switch fw
arm64: dts: ti: k3-j721e-common-proc-board: add virt cpsw9g mac node
net: ethernet: ti: introduce j721e virt cpsw-nuss mac driver
dt-bindings: net: Add binding for ti,j721e-cpsw-virt-mac device
rpmsg-kdrv: add support for remote eth device
dmaengine: ti: k3-navss-udma: add support for remote/virt udma channels
dmaengine: ti: k3-navss-udma: drop need_tisci_free
dmaengine: ti: k3-navss-udma: fix k3_nav_udmax_release_rx_flow()
dmaengine: ti: k3-navss-udma: fix gp rflow freeing in k3_nav_udmax_release_rx_chn()
dmaengine: ti: k3-navss-udma: fix access to udmax in k3_nav_udmax_release_rx_chn()
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Merged TI feature ti_linux_base_rt into ti-rt-linux-4.19.y
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel:
ti_config_fragments: add TIDSS_WB to audio_display.cfg
drm/tidss: add WB M2M driver
drm/tidss: add tidss_plane_reserve/release_wb
drm/tidss: Add WB config/setup helper
drm/tidss: Add RGB to YUV color conversion support
drm/tidss: add WB irq enable/status accessor
drm/tidss: add WB specific register offset
drm/tidss: add WB to io resource map
drm/tidss: static partition of wb
drm/tidss: add has_writeback flag
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
TI-Feature: ti_linux_base_rt
TI-Branch: ti-linux-4.19.y
* 'ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpub/ti-linux-kernel:
ti_config_fragments: add TIDSS_WB to audio_display.cfg
drm/tidss: add WB M2M driver
drm/tidss: add tidss_plane_reserve/release_wb
drm/tidss: Add WB config/setup helper
drm/tidss: Add RGB to YUV color conversion support
drm/tidss: add WB irq enable/status accessor
drm/tidss: add WB specific register offset
drm/tidss: add WB to io resource map
drm/tidss: static partition of wb
drm/tidss: add has_writeback flag
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
Merged TI feature audio-display into ti-linux-4.19.y
TI-Feature: audio-display
TI-Branch: audio_display-ti-linux-4.19.y
* 'audio_display-ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpublicdom/audio-display:
ti_config_fragments: add TIDSS_WB to audio_display.cfg
drm/tidss: add WB M2M driver
drm/tidss: add tidss_plane_reserve/release_wb
drm/tidss: Add WB config/setup helper
drm/tidss: Add RGB to YUV color conversion support
drm/tidss: add WB irq enable/status accessor
drm/tidss: add WB specific register offset
drm/tidss: add WB to io resource map
drm/tidss: static partition of wb
drm/tidss: add has_writeback flag
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
TI-Feature: audio-display
TI-Branch: audio_display-ti-linux-4.19.y
* 'audio_display-ti-linux-4.19.y' of ssh://bitbucket.itg.ti.com/lcpdpublicdom/audio-display:
ti_config_fragments: add TIDSS_WB to audio_display.cfg
drm/tidss: add WB M2M driver
drm/tidss: add tidss_plane_reserve/release_wb
drm/tidss: Add WB config/setup helper
drm/tidss: Add RGB to YUV color conversion support
drm/tidss: add WB irq enable/status accessor
drm/tidss: add WB specific register offset
drm/tidss: add WB to io resource map
drm/tidss: static partition of wb
drm/tidss: add has_writeback flag
Signed-off-by: LCPD Auto Merger <lcpd_integration@list.ti.com>
Merge branch 'for19.04.00' of ssh://bitbucket.itg.ti.com/~a0869644/ti-linux-kernel into audio_display-ti-linux-4.19.y
[GIT PULL] 2019.04 TIDSS WB (take #2)
* 'for19.04.00' of ssh://bitbucket.itg.ti.com/~a0869644/ti-linux-kernel:
ti_config_fragments: add TIDSS_WB to audio_display.cfg
drm/tidss: add WB M2M driver
drm/tidss: add tidss_plane_reserve/release_wb
drm/tidss: Add WB config/setup helper
drm/tidss: Add RGB to YUV color conversion support
drm/tidss: add WB irq enable/status accessor
drm/tidss: add WB specific register offset
drm/tidss: add WB to io resource map
drm/tidss: static partition of wb
drm/tidss: add has_writeback flag
[GIT PULL] 2019.04 TIDSS WB (take #2)
* 'for19.04.00' of ssh://bitbucket.itg.ti.com/~a0869644/ti-linux-kernel:
ti_config_fragments: add TIDSS_WB to audio_display.cfg
drm/tidss: add WB M2M driver
drm/tidss: add tidss_plane_reserve/release_wb
drm/tidss: Add WB config/setup helper
drm/tidss: Add RGB to YUV color conversion support
drm/tidss: add WB irq enable/status accessor
drm/tidss: add WB specific register offset
drm/tidss: add WB to io resource map
drm/tidss: static partition of wb
drm/tidss: add has_writeback flag
ti_config_fragments: add TIDSS_WB to audio_display.cfg
Add TIDSS WB config item to audio_display.cfg.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Add TIDSS WB config item to audio_display.cfg.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
drm/tidss: add WB M2M driver
DSS supports writing back the display unit output to memory.
Although it support several modes, this driver introduces the use of the
write-back (WB) feature as a method to perform memory 2 memory frame
conversion (M2M).
Signed-off-by: Benoit Parrot <bparrot@ti.com>
DSS supports writing back the display unit output to memory.
Although it support several modes, this driver introduces the use of the
write-back (WB) feature as a method to perform memory 2 memory frame
conversion (M2M).
Signed-off-by: Benoit Parrot <bparrot@ti.com>
drm/tidss: add tidss_plane_reserve/release_wb
Add functions to reserve and release a plane/OVR for writeback memory
to memory operation. Reserving a plane will prevent the display side
from using the plane while writeback is in progress by causing
tidss_plane_atomic_check() to return -EBUSY.
At probe time we figure out which OVR is available if any.
Then at runtime we try to find an available plane to use as the source
plane.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Add functions to reserve and release a plane/OVR for writeback memory
to memory operation. Reserving a plane will prevent the display side
from using the plane while writeback is in progress by causing
tidss_plane_atomic_check() to return -EBUSY.
At probe time we figure out which OVR is available if any.
Then at runtime we try to find an available plane to use as the source
plane.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
drm/tidss: Add WB config/setup helper
Create setup helpers to configure the write-back h/w pipeline.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Create setup helpers to configure the write-back h/w pipeline.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
drm/tidss: Add RGB to YUV color conversion support
Add the bt601/bt709 full and limited range RGB to YUV conversion tables.
Add color conversion direction to the csc lookup helper so either table
are search-able.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Add the bt601/bt709 full and limited range RGB to YUV conversion tables.
Add color conversion direction to the csc lookup helper so either table
are search-able.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
drm/tidss: add WB irq enable/status accessor
Add WB irqenable/irqstatus specific methods.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Add WB irqenable/irqstatus specific methods.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
drm/tidss: add WB specific register offset
Add specific WB register offset, which are similar to VID pipeline
offset but warrant a separate set to keep things modular and prevent
confusion.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Add specific WB register offset, which are similar to VID pipeline
offset but warrant a separate set to keep things modular and prevent
confusion.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
drm/tidss: add WB to io resource map
At init time make sure WB related memory region is mapped.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
At init time make sure WB related memory region is mapped.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
drm/tidss: static partition of wb
DSS7 has support for partitioning the write-back pipeline among the
several compute entities and they can be independently driven from
different cores.
This patch adds support for statically partitioning the write-back
pipeline using device-tree nodes.
If there is a DT node that specifies how the write-back pipeline should
be used, then the information is used to populate WB accordingly.
The .has_writeback flag is only check directly to decide if we need to
check the DT data for related writeback nodes.
dispc7_has_writeback() from this point forward will only check if WB is
managed by tidss or not.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
DSS7 has support for partitioning the write-back pipeline among the
several compute entities and they can be independently driven from
different cores.
This patch adds support for statically partitioning the write-back
pipeline using device-tree nodes.
If there is a DT node that specifies how the write-back pipeline should
be used, then the information is used to populate WB accordingly.
The .has_writeback flag is only check directly to decide if we need to
check the DT data for related writeback nodes.
dispc7_has_writeback() from this point forward will only check if WB is
managed by tidss or not.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Linux 4.19.73
vhost: make sure log_num < in_num
commit 060423bfdee3f8bc6e2c1bac97de24d5415e2bc4 upstream.
The code assumes log_num < in_num everywhere, and that is true as long as
in_num is incremented by descriptor iov count, and log_num by 1. However
this breaks if there's a zero sized descriptor.
As a result, if a malicious guest creates a vring desc with desc.len = 0,
it may cause the host kernel to crash by overflowing the log array. This
bug can be triggered during the VM migration.
There's no need to log when desc.len = 0, so just don't increment log_num
in this case.
Fixes: 3a4d5c94e959 ("vhost_net: a kernel-level virtio server")
Cc: stable@vger.kernel.org
Reviewed-by: Lidong Chen <lidongchen@tencent.com>
Signed-off-by: ruippan <ruippan@tencent.com>
Signed-off-by: yongduan <yongduan@tencent.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 060423bfdee3f8bc6e2c1bac97de24d5415e2bc4 upstream.
The code assumes log_num < in_num everywhere, and that is true as long as
in_num is incremented by descriptor iov count, and log_num by 1. However
this breaks if there's a zero sized descriptor.
As a result, if a malicious guest creates a vring desc with desc.len = 0,
it may cause the host kernel to crash by overflowing the log array. This
bug can be triggered during the VM migration.
There's no need to log when desc.len = 0, so just don't increment log_num
in this case.
Fixes: 3a4d5c94e959 ("vhost_net: a kernel-level virtio server")
Cc: stable@vger.kernel.org
Reviewed-by: Lidong Chen <lidongchen@tencent.com>
Signed-off-by: ruippan <ruippan@tencent.com>
Signed-off-by: yongduan <yongduan@tencent.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
powerpc/tm: Fix restoring FP/VMX facility incorrectly on interrupts
[ Upstream commit a8318c13e79badb92bc6640704a64cc022a6eb97 ]
When in userspace and MSR FP=0 the hardware FP state is unrelated to
the current process. This is extended for transactions where if tbegin
is run with FP=0, the hardware checkpoint FP state will also be
unrelated to the current process. Due to this, we need to ensure this
hardware checkpoint is updated with the correct state before we enable
FP for this process.
Unfortunately we get this wrong when returning to a process from a
hardware interrupt. A process that starts a transaction with FP=0 can
take an interrupt. When the kernel returns back to that process, we
change to FP=1 but with hardware checkpoint FP state not updated. If
this transaction is then rolled back, the FP registers now contain the
wrong state.
The process looks like this:
Userspace: Kernel
Start userspace
with MSR FP=0 TM=1
< -----
...
tbegin
bne
Hardware interrupt
---- >
<do_IRQ...>
....
ret_from_except
restore_math()
/* sees FP=0 */
restore_fp()
tm_active_with_fp()
/* sees FP=1 (Incorrect) */
load_fp_state()
FP = 0 -> 1
< -----
Return to userspace
with MSR TM=1 FP=1
with junk in the FP TM checkpoint
TM rollback
reads FP junk
When returning from the hardware exception, tm_active_with_fp() is
incorrectly making restore_fp() call load_fp_state() which is setting
FP=1.
The fix is to remove tm_active_with_fp().
tm_active_with_fp() is attempting to handle the case where FP state
has been changed inside a transaction. In this case the checkpointed
and transactional FP state is different and hence we must restore the
FP state (ie. we can't do lazy FP restore inside a transaction that's
used FP). It's safe to remove tm_active_with_fp() as this case is
handled by restore_tm_state(). restore_tm_state() detects if FP has
been using inside a transaction and will set load_fp and call
restore_math() to ensure the FP state (checkpoint and transaction) is
restored.
This is a data integrity problem for the current process as the FP
registers are corrupted. It's also a security problem as the FP
registers from one process may be leaked to another.
Similarly for VMX.
A simple testcase to replicate this will be posted to
tools/testing/selftests/powerpc/tm/tm-poison.c
This fixes CVE-2019-15031.
Fixes: a7771176b439 ("powerpc: Don't enable FP/Altivec if not checkpointed")
Cc: stable@vger.kernel.org # 4.15+
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190904045529.23002-2-gromero@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8318c13e79badb92bc6640704a64cc022a6eb97 ]
When in userspace and MSR FP=0 the hardware FP state is unrelated to
the current process. This is extended for transactions where if tbegin
is run with FP=0, the hardware checkpoint FP state will also be
unrelated to the current process. Due to this, we need to ensure this
hardware checkpoint is updated with the correct state before we enable
FP for this process.
Unfortunately we get this wrong when returning to a process from a
hardware interrupt. A process that starts a transaction with FP=0 can
take an interrupt. When the kernel returns back to that process, we
change to FP=1 but with hardware checkpoint FP state not updated. If
this transaction is then rolled back, the FP registers now contain the
wrong state.
The process looks like this:
Userspace: Kernel
Start userspace
with MSR FP=0 TM=1
< -----
...
tbegin
bne
Hardware interrupt
---- >
<do_IRQ...>
....
ret_from_except
restore_math()
/* sees FP=0 */
restore_fp()
tm_active_with_fp()
/* sees FP=1 (Incorrect) */
load_fp_state()
FP = 0 -> 1
< -----
Return to userspace
with MSR TM=1 FP=1
with junk in the FP TM checkpoint
TM rollback
reads FP junk
When returning from the hardware exception, tm_active_with_fp() is
incorrectly making restore_fp() call load_fp_state() which is setting
FP=1.
The fix is to remove tm_active_with_fp().
tm_active_with_fp() is attempting to handle the case where FP state
has been changed inside a transaction. In this case the checkpointed
and transactional FP state is different and hence we must restore the
FP state (ie. we can't do lazy FP restore inside a transaction that's
used FP). It's safe to remove tm_active_with_fp() as this case is
handled by restore_tm_state(). restore_tm_state() detects if FP has
been using inside a transaction and will set load_fp and call
restore_math() to ensure the FP state (checkpoint and transaction) is
restored.
This is a data integrity problem for the current process as the FP
registers are corrupted. It's also a security problem as the FP
registers from one process may be leaked to another.
Similarly for VMX.
A simple testcase to replicate this will be posted to
tools/testing/selftests/powerpc/tm/tm-poison.c
This fixes CVE-2019-15031.
Fixes: a7771176b439 ("powerpc: Don't enable FP/Altivec if not checkpointed")
Cc: stable@vger.kernel.org # 4.15+
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190904045529.23002-2-gromero@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
powerpc/tm: Remove msr_tm_active()
[ Upstream commit 5c784c8414fba11b62e12439f11e109fb5751f38 ]
Currently msr_tm_active() is a wrapper around MSR_TM_ACTIVE() if
CONFIG_PPC_TRANSACTIONAL_MEM is set, or it is just a function that
returns false if CONFIG_PPC_TRANSACTIONAL_MEM is not set.
This function is not necessary, since MSR_TM_ACTIVE() just do the same and
could be used, removing the dualism and simplifying the code.
This patchset remove every instance of msr_tm_active() and replaced it
by MSR_TM_ACTIVE().
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c784c8414fba11b62e12439f11e109fb5751f38 ]
Currently msr_tm_active() is a wrapper around MSR_TM_ACTIVE() if
CONFIG_PPC_TRANSACTIONAL_MEM is set, or it is just a function that
returns false if CONFIG_PPC_TRANSACTIONAL_MEM is not set.
This function is not necessary, since MSR_TM_ACTIVE() just do the same and
could be used, removing the dualism and simplifying the code.
This patchset remove every instance of msr_tm_active() and replaced it
by MSR_TM_ACTIVE().
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
PCI: Reset both NVIDIA GPU and HDA in ThinkPad P50 workaround
[ Upstream commit ad54567ad5d8e938ee6cf02e4f3867f18835ae6e ]
quirk_reset_lenovo_thinkpad_50_nvgpu() resets NVIDIA GPUs to work around
an apparent BIOS defect. It previously used pci_reset_function(), and
the available method was a bus reset, which was fine because there was
only one function on the bus. After b516ea586d71 ("PCI: Enable NVIDIA
HDA controllers"), there are now two functions (the HDA controller and
the GPU itself) on the bus, so the reset fails.
Use pci_reset_bus() explicitly instead of pci_reset_function() since it's
OK to reset both devices.
[bhelgaas: commit log, add e0547c81bfcf]
Fixes: b516ea586d71 ("PCI: Enable NVIDIA HDA controllers")
Fixes: e0547c81bfcf ("PCI: Reset Lenovo ThinkPad P50 nvgpu at boot if necessary")
Link: https://lore.kernel.org/r/20190801220117.14952-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Drake <drake@endlessm.com>
Cc: Aaron Plattner <aplattner@nvidia.com>
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Maik Freudenberg <hhfeuer@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad54567ad5d8e938ee6cf02e4f3867f18835ae6e ]
quirk_reset_lenovo_thinkpad_50_nvgpu() resets NVIDIA GPUs to work around
an apparent BIOS defect. It previously used pci_reset_function(), and
the available method was a bus reset, which was fine because there was
only one function on the bus. After b516ea586d71 ("PCI: Enable NVIDIA
HDA controllers"), there are now two functions (the HDA controller and
the GPU itself) on the bus, so the reset fails.
Use pci_reset_bus() explicitly instead of pci_reset_function() since it's
OK to reset both devices.
[bhelgaas: commit log, add e0547c81bfcf]
Fixes: b516ea586d71 ("PCI: Enable NVIDIA HDA controllers")
Fixes: e0547c81bfcf ("PCI: Reset Lenovo ThinkPad P50 nvgpu at boot if necessary")
Link: https://lore.kernel.org/r/20190801220117.14952-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Drake <drake@endlessm.com>
Cc: Aaron Plattner <aplattner@nvidia.com>
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Maik Freudenberg <hhfeuer@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ext4: unsigned int compared against zero
[ Upstream commit fbbbbd2f28aec991f3fbc248df211550fbdfd58c ]
There are two cases where u32 variables n and err are being checked
for less than zero error values, the checks is always false because
the variables are not signed. Fix this by making the variables ints.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: 345c0dbf3a30 ("ext4: protect journal inode's blocks using block_validity")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbbbbd2f28aec991f3fbc248df211550fbdfd58c ]
There are two cases where u32 variables n and err are being checked
for less than zero error values, the checks is always false because
the variables are not signed. Fix this by making the variables ints.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: 345c0dbf3a30 ("ext4: protect journal inode's blocks using block_validity")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ext4: fix block validity checks for journal inodes using indirect blocks
[ Upstream commit 170417c8c7bb2cbbdd949bf5c443c0c8f24a203b ]
Commit 345c0dbf3a30 ("ext4: protect journal inode's blocks using
block_validity") failed to add an exception for the journal inode in
ext4_check_blockref(), which is the function used by ext4_get_branch()
for indirect blocks. This caused attempts to read from the ext3-style
journals to fail with:
[ 848.968550] EXT4-fs error (device sdb7): ext4_get_branch:171: inode #8: block 30343695: comm jbd2/sdb7-8: invalid block
Fix this by adding the missing exception check.
Fixes: 345c0dbf3a30 ("ext4: protect journal inode's blocks using block_validity")
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 170417c8c7bb2cbbdd949bf5c443c0c8f24a203b ]
Commit 345c0dbf3a30 ("ext4: protect journal inode's blocks using
block_validity") failed to add an exception for the journal inode in
ext4_check_blockref(), which is the function used by ext4_get_branch()
for indirect blocks. This caused attempts to read from the ext3-style
journals to fail with:
[ 848.968550] EXT4-fs error (device sdb7): ext4_get_branch:171: inode #8: block 30343695: comm jbd2/sdb7-8: invalid block
Fix this by adding the missing exception check.
Fixes: 345c0dbf3a30 ("ext4: protect journal inode's blocks using block_validity")
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ext4: don't perform block validity checks on the journal inode
[ Upstream commit 0a944e8a6c66ca04c7afbaa17e22bf208a8b37f0 ]
Since the journal inode is already checked when we added it to the
block validity's system zone, if we check it again, we'll just trigger
a failure.
This was causing failures like this:
[ 53.897001] EXT4-fs error (device sda): ext4_find_extent:909: inode
#8: comm jbd2/sda-8: pblk 121667583 bad header/extent: invalid extent entries - magic f30a, entries 8, max 340(340), depth 0(0)
[ 53.931430] jbd2_journal_bmap: journal block not found at offset 49 on sda-8
[ 53.938480] Aborting journal on device sda-8.
... but only if the system was under enough memory pressure that
logical->physical mapping for the journal inode gets pushed out of the
extent cache. (This is why it wasn't noticed earlier.)
Fixes: 345c0dbf3a30 ("ext4: protect journal inode's blocks using block_validity")
Reported-by: Dan Rue <dan.rue@linaro.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a944e8a6c66ca04c7afbaa17e22bf208a8b37f0 ]
Since the journal inode is already checked when we added it to the
block validity's system zone, if we check it again, we'll just trigger
a failure.
This was causing failures like this:
[ 53.897001] EXT4-fs error (device sda): ext4_find_extent:909: inode
#8: comm jbd2/sda-8: pblk 121667583 bad header/extent: invalid extent entries - magic f30a, entries 8, max 340(340), depth 0(0)
[ 53.931430] jbd2_journal_bmap: journal block not found at offset 49 on sda-8
[ 53.938480] Aborting journal on device sda-8.
... but only if the system was under enough memory pressure that
logical->physical mapping for the journal inode gets pushed out of the
extent cache. (This is why it wasn't noticed earlier.)
Fixes: 345c0dbf3a30 ("ext4: protect journal inode's blocks using block_validity")
Reported-by: Dan Rue <dan.rue@linaro.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
drm/atomic_helper: Allow DPMS On<->Off changes for unregistered connectors
[ Upstream commit 34ca26a98ad67edd6e4870fe2d4aa047d41a51dd ]
It appears when testing my previous fix for some of the legacy
modesetting issues with MST, I misattributed some kernel splats that
started appearing on my machine after a rebase as being from upstream.
But it appears they actually came from my patch series:
[ 2.980512] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:65:eDP-1]
[ 2.980516] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CONNECTOR:65:eDP-1] is not registered
[ 2.980516] ------------[ cut here ]------------
[ 2.980519] Could not determine valid watermarks for inherited state
[ 2.980553] WARNING: CPU: 3 PID: 551 at drivers/gpu/drm/i915/intel_display.c:14983 intel_modeset_init+0x14d7/0x19f0 [i915]
[ 2.980556] Modules linked in: i915(O+) i2c_algo_bit drm_kms_helper(O) syscopyarea sysfillrect sysimgblt fb_sys_fops drm(O) intel_rapl x86_pkg_temp_thermal iTCO_wdt wmi_bmof coretemp crc32_pclmul psmouse i2c_i801 mei_me mei i2c_core lpc_ich mfd_core tpm_tis tpm_tis_core wmi tpm thinkpad_acpi pcc_cpufreq video ehci_pci crc32c_intel serio_raw ehci_hcd xhci_pci xhci_hcd
[ 2.980577] CPU: 3 PID: 551 Comm: systemd-udevd Tainted: G O 4.19.0-rc7Lyude-Test+ #1
[ 2.980579] Hardware name: LENOVO 20BWS1KY00/20BWS1KY00, BIOS JBET63WW (1.27 ) 11/10/2016
[ 2.980605] RIP: 0010:intel_modeset_init+0x14d7/0x19f0 [i915]
[ 2.980607] Code: 89 df e8 ec 27 02 00 e9 24 f2 ff ff be 03 00 00 00 48 89 df e8 da 27 02 00 e9 26 f2 ff ff 48 c7 c7 c8 d1 34 a0 e8 23 cf dc e0 <0f> 0b e9 7c fd ff ff f6 c4 04 0f 85 37 f7 ff ff 48 8b 83 60 08 00
[ 2.980611] RSP: 0018:ffffc90000287988 EFLAGS: 00010282
[ 2.980614] RAX: 0000000000000000 RBX: ffff88031b488000 RCX: 0000000000000006
[ 2.980617] RDX: 0000000000000007 RSI: 0000000000000086 RDI: ffff880321ad54d0
[ 2.980620] RBP: ffffc90000287a10 R08: 000000000000040a R09: 0000000000000065
[ 2.980623] R10: ffff88030ebb8f00 R11: ffffffff81416590 R12: ffff88031b488000
[ 2.980626] R13: ffff88031b4883a0 R14: ffffc900002879a8 R15: ffff880319099800
[ 2.980630] FS: 00007f475620d180(0000) GS:ffff880321ac0000(0000) knlGS:0000000000000000
[ 2.980633] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2.980636] CR2: 00007f9ef28018a0 CR3: 000000031b72c001 CR4: 00000000003606e0
[ 2.980639] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2.980642] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 2.980645] Call Trace:
[ 2.980675] i915_driver_load+0xb0e/0xdc0 [i915]
[ 2.980681] ? kernfs_add_one+0xe7/0x130
[ 2.980709] i915_pci_probe+0x46/0x60 [i915]
[ 2.980715] pci_device_probe+0xd4/0x150
[ 2.980719] really_probe+0x243/0x3b0
[ 2.980722] driver_probe_device+0xba/0x100
[ 2.980726] __driver_attach+0xe4/0x110
[ 2.980729] ? driver_probe_device+0x100/0x100
[ 2.980733] bus_for_each_dev+0x74/0xb0
[ 2.980736] driver_attach+0x1e/0x20
[ 2.980739] bus_add_driver+0x159/0x230
[ 2.980743] ? 0xffffffffa0393000
[ 2.980746] driver_register+0x70/0xc0
[ 2.980749] ? 0xffffffffa0393000
[ 2.980753] __pci_register_driver+0x57/0x60
[ 2.980780] i915_init+0x55/0x58 [i915]
[ 2.980785] do_one_initcall+0x4a/0x1c4
[ 2.980789] ? do_init_module+0x27/0x210
[ 2.980793] ? kmem_cache_alloc_trace+0x131/0x190
[ 2.980797] do_init_module+0x60/0x210
[ 2.980800] load_module+0x2063/0x22e0
[ 2.980804] ? vfs_read+0x116/0x140
[ 2.980807] ? vfs_read+0x116/0x140
[ 2.980811] __do_sys_finit_module+0xbd/0x120
[ 2.980814] ? __do_sys_finit_module+0xbd/0x120
[ 2.980818] __x64_sys_finit_module+0x1a/0x20
[ 2.980821] do_syscall_64+0x5a/0x110
[ 2.980824] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 2.980826] RIP: 0033:0x7f4754e32879
[ 2.980828] Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d f7 45 2c 00 f7 d8 64 89 01 48
[ 2.980831] RSP: 002b:00007fff43fd97d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 2.980834] RAX: ffffffffffffffda RBX: 0000559a44ca64f0 RCX: 00007f4754e32879
[ 2.980836] RDX: 0000000000000000 RSI: 00007f475599f4cd RDI: 0000000000000018
[ 2.980838] RBP: 00007f475599f4cd R08: 0000000000000000 R09: 0000000000000000
[ 2.980839] R10: 0000000000000018 R11: 0000000000000246 R12: 0000000000000000
[ 2.980841] R13: 0000559a44c92fd0 R14: 0000000000020000 R15: 0000000000000000
[ 2.980881] WARNING: CPU: 3 PID: 551 at drivers/gpu/drm/i915/intel_display.c:14983 intel_modeset_init+0x14d7/0x19f0 [i915]
[ 2.980884] ---[ end trace 5eb47a76277d4731 ]---
The cause of this appears to be due to the fact that if there's
pre-existing display state that was set by the BIOS when i915 loads, it
will attempt to perform a modeset before the driver is registered with
userspace. Since this happens before the driver's registered with
userspace, it's connectors are also unregistered and thus-states which
would turn on DPMS on a connector end up getting rejected since the
connector isn't registered.
These bugs managed to get past Intel's CI partially due to the fact it
never ran a full test on my patches for some reason, but also because
all of the tests unload the GPU once before running. Since this bug is
only really triggered when the drivers tries to perform a modeset before
it's been fully registered with userspace when coming from whatever
display configuration the firmware left us with, it likely would never
have been picked up by CI in the first place.
After some discussion with vsyrjala, we decided the best course of
action would be to just move the unregistered connector checks out of
update_connector_routing() and into drm_atomic_set_crtc_for_connector().
The reason for this being that legacy modesetting isn't going to be
expecting failures anywhere (at least this is the case with X), so
ideally we want to ensure that any DPMS changes will still work even on
unregistered connectors. Instead, we now only reject new modesets which
would change the current CRTC assigned to an unregistered connector
unless no new CRTC is being assigned to replace the connector's previous
one.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 4d80273976bf ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009204424.21462-1-lyude@redhat.com
(cherry picked from commit b5d29843d8ef86d4cde4742e095b81b7fd41e688)
Fixes: e96550956fbc ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34ca26a98ad67edd6e4870fe2d4aa047d41a51dd ]
It appears when testing my previous fix for some of the legacy
modesetting issues with MST, I misattributed some kernel splats that
started appearing on my machine after a rebase as being from upstream.
But it appears they actually came from my patch series:
[ 2.980512] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:65:eDP-1]
[ 2.980516] [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CONNECTOR:65:eDP-1] is not registered
[ 2.980516] ------------[ cut here ]------------
[ 2.980519] Could not determine valid watermarks for inherited state
[ 2.980553] WARNING: CPU: 3 PID: 551 at drivers/gpu/drm/i915/intel_display.c:14983 intel_modeset_init+0x14d7/0x19f0 [i915]
[ 2.980556] Modules linked in: i915(O+) i2c_algo_bit drm_kms_helper(O) syscopyarea sysfillrect sysimgblt fb_sys_fops drm(O) intel_rapl x86_pkg_temp_thermal iTCO_wdt wmi_bmof coretemp crc32_pclmul psmouse i2c_i801 mei_me mei i2c_core lpc_ich mfd_core tpm_tis tpm_tis_core wmi tpm thinkpad_acpi pcc_cpufreq video ehci_pci crc32c_intel serio_raw ehci_hcd xhci_pci xhci_hcd
[ 2.980577] CPU: 3 PID: 551 Comm: systemd-udevd Tainted: G O 4.19.0-rc7Lyude-Test+ #1
[ 2.980579] Hardware name: LENOVO 20BWS1KY00/20BWS1KY00, BIOS JBET63WW (1.27 ) 11/10/2016
[ 2.980605] RIP: 0010:intel_modeset_init+0x14d7/0x19f0 [i915]
[ 2.980607] Code: 89 df e8 ec 27 02 00 e9 24 f2 ff ff be 03 00 00 00 48 89 df e8 da 27 02 00 e9 26 f2 ff ff 48 c7 c7 c8 d1 34 a0 e8 23 cf dc e0 <0f> 0b e9 7c fd ff ff f6 c4 04 0f 85 37 f7 ff ff 48 8b 83 60 08 00
[ 2.980611] RSP: 0018:ffffc90000287988 EFLAGS: 00010282
[ 2.980614] RAX: 0000000000000000 RBX: ffff88031b488000 RCX: 0000000000000006
[ 2.980617] RDX: 0000000000000007 RSI: 0000000000000086 RDI: ffff880321ad54d0
[ 2.980620] RBP: ffffc90000287a10 R08: 000000000000040a R09: 0000000000000065
[ 2.980623] R10: ffff88030ebb8f00 R11: ffffffff81416590 R12: ffff88031b488000
[ 2.980626] R13: ffff88031b4883a0 R14: ffffc900002879a8 R15: ffff880319099800
[ 2.980630] FS: 00007f475620d180(0000) GS:ffff880321ac0000(0000) knlGS:0000000000000000
[ 2.980633] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2.980636] CR2: 00007f9ef28018a0 CR3: 000000031b72c001 CR4: 00000000003606e0
[ 2.980639] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2.980642] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 2.980645] Call Trace:
[ 2.980675] i915_driver_load+0xb0e/0xdc0 [i915]
[ 2.980681] ? kernfs_add_one+0xe7/0x130
[ 2.980709] i915_pci_probe+0x46/0x60 [i915]
[ 2.980715] pci_device_probe+0xd4/0x150
[ 2.980719] really_probe+0x243/0x3b0
[ 2.980722] driver_probe_device+0xba/0x100
[ 2.980726] __driver_attach+0xe4/0x110
[ 2.980729] ? driver_probe_device+0x100/0x100
[ 2.980733] bus_for_each_dev+0x74/0xb0
[ 2.980736] driver_attach+0x1e/0x20
[ 2.980739] bus_add_driver+0x159/0x230
[ 2.980743] ? 0xffffffffa0393000
[ 2.980746] driver_register+0x70/0xc0
[ 2.980749] ? 0xffffffffa0393000
[ 2.980753] __pci_register_driver+0x57/0x60
[ 2.980780] i915_init+0x55/0x58 [i915]
[ 2.980785] do_one_initcall+0x4a/0x1c4
[ 2.980789] ? do_init_module+0x27/0x210
[ 2.980793] ? kmem_cache_alloc_trace+0x131/0x190
[ 2.980797] do_init_module+0x60/0x210
[ 2.980800] load_module+0x2063/0x22e0
[ 2.980804] ? vfs_read+0x116/0x140
[ 2.980807] ? vfs_read+0x116/0x140
[ 2.980811] __do_sys_finit_module+0xbd/0x120
[ 2.980814] ? __do_sys_finit_module+0xbd/0x120
[ 2.980818] __x64_sys_finit_module+0x1a/0x20
[ 2.980821] do_syscall_64+0x5a/0x110
[ 2.980824] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 2.980826] RIP: 0033:0x7f4754e32879
[ 2.980828] Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d f7 45 2c 00 f7 d8 64 89 01 48
[ 2.980831] RSP: 002b:00007fff43fd97d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 2.980834] RAX: ffffffffffffffda RBX: 0000559a44ca64f0 RCX: 00007f4754e32879
[ 2.980836] RDX: 0000000000000000 RSI: 00007f475599f4cd RDI: 0000000000000018
[ 2.980838] RBP: 00007f475599f4cd R08: 0000000000000000 R09: 0000000000000000
[ 2.980839] R10: 0000000000000018 R11: 0000000000000246 R12: 0000000000000000
[ 2.980841] R13: 0000559a44c92fd0 R14: 0000000000020000 R15: 0000000000000000
[ 2.980881] WARNING: CPU: 3 PID: 551 at drivers/gpu/drm/i915/intel_display.c:14983 intel_modeset_init+0x14d7/0x19f0 [i915]
[ 2.980884] ---[ end trace 5eb47a76277d4731 ]---
The cause of this appears to be due to the fact that if there's
pre-existing display state that was set by the BIOS when i915 loads, it
will attempt to perform a modeset before the driver is registered with
userspace. Since this happens before the driver's registered with
userspace, it's connectors are also unregistered and thus-states which
would turn on DPMS on a connector end up getting rejected since the
connector isn't registered.
These bugs managed to get past Intel's CI partially due to the fact it
never ran a full test on my patches for some reason, but also because
all of the tests unload the GPU once before running. Since this bug is
only really triggered when the drivers tries to perform a modeset before
it's been fully registered with userspace when coming from whatever
display configuration the firmware left us with, it likely would never
have been picked up by CI in the first place.
After some discussion with vsyrjala, we decided the best course of
action would be to just move the unregistered connector checks out of
update_connector_routing() and into drm_atomic_set_crtc_for_connector().
The reason for this being that legacy modesetting isn't going to be
expecting failures anywhere (at least this is the case with X), so
ideally we want to ensure that any DPMS changes will still work even on
unregistered connectors. Instead, we now only reject new modesets which
would change the current CRTC assigned to an unregistered connector
unless no new CRTC is being assigned to replace the connector's previous
one.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 4d80273976bf ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009204424.21462-1-lyude@redhat.com
(cherry picked from commit b5d29843d8ef86d4cde4742e095b81b7fd41e688)
Fixes: e96550956fbc ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
virtio/s390: fix race on airq_areas[]
[ Upstream commit 4f419eb14272e0698e8c55bb5f3f266cc2a21c81 ]
The access to airq_areas was racy ever since the adapter interrupts got
introduced to virtio-ccw, but since commit 39c7dcb15892 ("virtio/s390:
make airq summary indicators DMA") this became an issue in practice as
well. Namely before that commit the airq_info that got overwritten was
still functional. After that commit however the two infos share a
summary_indicator, which aggravates the situation. Which means
auto-online mechanism occasionally hangs the boot with virtio_blk.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 96b14536d935 ("virtio-ccw: virtio-ccw adapter interrupt support.")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f419eb14272e0698e8c55bb5f3f266cc2a21c81 ]
The access to airq_areas was racy ever since the adapter interrupts got
introduced to virtio-ccw, but since commit 39c7dcb15892 ("virtio/s390:
make airq summary indicators DMA") this became an issue in practice as
well. Namely before that commit the airq_info that got overwritten was
still functional. After that commit however the two infos share a
summary_indicator, which aggravates the situation. Which means
auto-online mechanism occasionally hangs the boot with virtio_blk.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 96b14536d935 ("virtio-ccw: virtio-ccw adapter interrupt support.")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
drm/i915: Make sure cdclk is high enough for DP audio on VLV/CHV
[ Upstream commit a8f196a0fa6391a436f63f360a1fb57031fdf26c ]
On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
meet the following requirements:
DP Link Frequency(MHz) | Cdclk frequency(MHz)
270 | 320 or higher
162 | 200 or higher"
I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.
Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.
v2: Spell out the cdclk and link frequencies we actually support
Cc: stable@vger.kernel.org
Tested-by: Stefan Gottwald <gottwald@igel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111149
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717114536.22937-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit bffb31f73b29a60ef693842d8744950c2819851d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8f196a0fa6391a436f63f360a1fb57031fdf26c ]
On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
meet the following requirements:
DP Link Frequency(MHz) | Cdclk frequency(MHz)
270 | 320 or higher
162 | 200 or higher"
I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.
Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.
v2: Spell out the cdclk and link frequencies we actually support
Cc: stable@vger.kernel.org
Tested-by: Stefan Gottwald <gottwald@igel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111149
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717114536.22937-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit bffb31f73b29a60ef693842d8744950c2819851d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
bcache: fix race in btree_flush_write()
[ Upstream commit 50a260e859964002dab162513a10f91ae9d3bcd3 ]
There is a race between mca_reap(), btree_node_free() and journal code
btree_flush_write(), which results very rare and strange deadlock or
panic and are very hard to reproduce.
Let me explain how the race happens. In btree_flush_write() one btree
node with oldest journal pin is selected, then it is flushed to cache
device, the select-and-flush is a two steps operation. Between these two
steps, there are something may happen inside the race window,
- The selected btree node was reaped by mca_reap() and allocated to
other requesters for other btree node.
- The slected btree node was selected, flushed and released by mca
shrink callback bch_mca_scan().
When btree_flush_write() tries to flush the selected btree node, firstly
b->write_lock is held by mutex_lock(). If the race happens and the
memory of selected btree node is allocated to other btree node, if that
btree node's write_lock is held already, a deadlock very probably
happens here. A worse case is the memory of the selected btree node is
released, then all references to this btree node (e.g. b->write_lock)
will trigger NULL pointer deference panic.
This race was introduced in commit cafe56359144 ("bcache: A block layer
cache"), and enlarged by commit c4dc2497d50d ("bcache: fix high CPU
occupancy during journal"), which selected 128 btree nodes and flushed
them one-by-one in a quite long time period.
Such race is not easy to reproduce before. On a Lenovo SR650 server with
48 Xeon cores, and configure 1 NVMe SSD as cache device, a MD raid0
device assembled by 3 NVMe SSDs as backing device, this race can be
observed around every 10,000 times btree_flush_write() gets called. Both
deadlock and kernel panic all happened as aftermath of the race.
The idea of the fix is to add a btree flag BTREE_NODE_journal_flush. It
is set when selecting btree nodes, and cleared after btree nodes
flushed. Then when mca_reap() selects a btree node with this bit set,
this btree node will be skipped. Since mca_reap() only reaps btree node
without BTREE_NODE_journal_flush flag, such race is avoided.
Once corner case should be noticed, that is btree_node_free(). It might
be called in some error handling code path. For example the following
code piece from btree_split(),
2149 err_free2:
2150 bkey_put(b->c, &n2->key);
2151 btree_node_free(n2);
2152 rw_unlock(true, n2);
2153 err_free1:
2154 bkey_put(b->c, &n1->key);
2155 btree_node_free(n1);
2156 rw_unlock(true, n1);
At line 2151 and 2155, the btree node n2 and n1 are released without
mac_reap(), so BTREE_NODE_journal_flush also needs to be checked here.
If btree_node_free() is called directly in such error handling path,
and the selected btree node has BTREE_NODE_journal_flush bit set, just
delay for 1 us and retry again. In this case this btree node won't
be skipped, just retry until the BTREE_NODE_journal_flush bit cleared,
and free the btree node memory.
Fixes: cafe56359144 ("bcache: A block layer cache")
Signed-off-by: Coly Li <colyli@suse.de>
Reported-and-tested-by: kbuild test robot <lkp@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50a260e859964002dab162513a10f91ae9d3bcd3 ]
There is a race between mca_reap(), btree_node_free() and journal code
btree_flush_write(), which results very rare and strange deadlock or
panic and are very hard to reproduce.
Let me explain how the race happens. In btree_flush_write() one btree
node with oldest journal pin is selected, then it is flushed to cache
device, the select-and-flush is a two steps operation. Between these two
steps, there are something may happen inside the race window,
- The selected btree node was reaped by mca_reap() and allocated to
other requesters for other btree node.
- The slected btree node was selected, flushed and released by mca
shrink callback bch_mca_scan().
When btree_flush_write() tries to flush the selected btree node, firstly
b->write_lock is held by mutex_lock(). If the race happens and the
memory of selected btree node is allocated to other btree node, if that
btree node's write_lock is held already, a deadlock very probably
happens here. A worse case is the memory of the selected btree node is
released, then all references to this btree node (e.g. b->write_lock)
will trigger NULL pointer deference panic.
This race was introduced in commit cafe56359144 ("bcache: A block layer
cache"), and enlarged by commit c4dc2497d50d ("bcache: fix high CPU
occupancy during journal"), which selected 128 btree nodes and flushed
them one-by-one in a quite long time period.
Such race is not easy to reproduce before. On a Lenovo SR650 server with
48 Xeon cores, and configure 1 NVMe SSD as cache device, a MD raid0
device assembled by 3 NVMe SSDs as backing device, this race can be
observed around every 10,000 times btree_flush_write() gets called. Both
deadlock and kernel panic all happened as aftermath of the race.
The idea of the fix is to add a btree flag BTREE_NODE_journal_flush. It
is set when selecting btree nodes, and cleared after btree nodes
flushed. Then when mca_reap() selects a btree node with this bit set,
this btree node will be skipped. Since mca_reap() only reaps btree node
without BTREE_NODE_journal_flush flag, such race is avoided.
Once corner case should be noticed, that is btree_node_free(). It might
be called in some error handling code path. For example the following
code piece from btree_split(),
2149 err_free2:
2150 bkey_put(b->c, &n2->key);
2151 btree_node_free(n2);
2152 rw_unlock(true, n2);
2153 err_free1:
2154 bkey_put(b->c, &n1->key);
2155 btree_node_free(n1);
2156 rw_unlock(true, n1);
At line 2151 and 2155, the btree node n2 and n1 are released without
mac_reap(), so BTREE_NODE_journal_flush also needs to be checked here.
If btree_node_free() is called directly in such error handling path,
and the selected btree node has BTREE_NODE_journal_flush bit set, just
delay for 1 us and retry again. In this case this btree node won't
be skipped, just retry until the BTREE_NODE_journal_flush bit cleared,
and free the btree node memory.
Fixes: cafe56359144 ("bcache: A block layer cache")
Signed-off-by: Coly Li <colyli@suse.de>
Reported-and-tested-by: kbuild test robot <lkp@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
bcache: add comments for mutex_lock(&b->write_lock)
[ Upstream commit 41508bb7d46b74dba631017e5a702a86caf1db8c ]
When accessing or modifying BTREE_NODE_dirty bit, it is not always
necessary to acquire b->write_lock. In bch_btree_cache_free() and
mca_reap() acquiring b->write_lock is necessary, and this patch adds
comments to explain why mutex_lock(&b->write_lock) is necessary for
checking or clearing BTREE_NODE_dirty bit there.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41508bb7d46b74dba631017e5a702a86caf1db8c ]
When accessing or modifying BTREE_NODE_dirty bit, it is not always
necessary to acquire b->write_lock. In bch_btree_cache_free() and
mca_reap() acquiring b->write_lock is necessary, and this patch adds
comments to explain why mutex_lock(&b->write_lock) is necessary for
checking or clearing BTREE_NODE_dirty bit there.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
bcache: only clear BTREE_NODE_dirty bit when it is set
[ Upstream commit e5ec5f4765ada9c75fb3eee93a6e72f0e50599d5 ]
In bch_btree_cache_free() and btree_node_free(), BTREE_NODE_dirty is
always set no matter btree node is dirty or not. The code looks like
this,
if (btree_node_dirty(b))
btree_complete_write(b, btree_current_write(b));
clear_bit(BTREE_NODE_dirty, &b->flags);
Indeed if btree_node_dirty(b) returns false, it means BTREE_NODE_dirty
bit is cleared, then it is unnecessary to clear the bit again.
This patch only clears BTREE_NODE_dirty when btree_node_dirty(b) is
true (the bit is set), to save a few CPU cycles.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5ec5f4765ada9c75fb3eee93a6e72f0e50599d5 ]
In bch_btree_cache_free() and btree_node_free(), BTREE_NODE_dirty is
always set no matter btree node is dirty or not. The code looks like
this,
if (btree_node_dirty(b))
btree_complete_write(b, btree_current_write(b));
clear_bit(BTREE_NODE_dirty, &b->flags);
Indeed if btree_node_dirty(b) returns false, it means BTREE_NODE_dirty
bit is cleared, then it is unnecessary to clear the bit again.
This patch only clears BTREE_NODE_dirty when btree_node_dirty(b) is
true (the bit is set), to save a few CPU cycles.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
NFSv4: Fix delegation state recovery
[ Upstream commit 5eb8d18ca0e001c6055da2b7f30d8f6dca23a44f ]
Once we clear the NFS_DELEGATED_STATE flag, we're telling
nfs_delegation_claim_opens() that we're done recovering all open state
for that stateid, so we really need to ensure that we test for all
open modes that are currently cached and recover them before exiting
nfs4_open_delegation_recall().
Fixes: 24311f884189d ("NFSv4: Recovery of recalled read delegations...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eb8d18ca0e001c6055da2b7f30d8f6dca23a44f ]
Once we clear the NFS_DELEGATED_STATE flag, we're telling
nfs_delegation_claim_opens() that we're done recovering all open state
for that stateid, so we really need to ensure that we test for all
open modes that are currently cached and recover them before exiting
nfs4_open_delegation_recall().
Fixes: 24311f884189d ("NFSv4: Recovery of recalled read delegations...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Sasha Levin <sashal@kernel.org>
iio: adc: gyroadc: fix uninitialized return code
[ Upstream commit 90c6260c1905a68fb596844087f2223bd4657fee ]
gcc-9 complains about a blatant uninitialized variable use that
all earlier compiler versions missed:
drivers/iio/adc/rcar-gyroadc.c:510:5: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Return -EINVAL instead here and a few lines above it where
we accidentally return 0 on failure.
Cc: stable@vger.kernel.org
Fixes: 059c53b32329 ("iio: adc: Add Renesas GyroADC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90c6260c1905a68fb596844087f2223bd4657fee ]
gcc-9 complains about a blatant uninitialized variable use that
all earlier compiler versions missed:
drivers/iio/adc/rcar-gyroadc.c:510:5: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Return -EINVAL instead here and a few lines above it where
we accidentally return 0 on failure.
Cc: stable@vger.kernel.org
Fixes: 059c53b32329 ("iio: adc: Add Renesas GyroADC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mm/migrate.c: initialize pud_entry in migrate_vma()
[ Upstream commit 7b358c6f12dc82364f6d317f8c8f1d794adbc3f5 ]
When CONFIG_MIGRATE_VMA_HELPER is enabled, migrate_vma() calls
migrate_vma_collect() which initializes a struct mm_walk but didn't
initialize mm_walk.pud_entry. (Found by code inspection) Use a C
structure initialization to make sure it is set to NULL.
Link: http://lkml.kernel.org/r/20190719233225.12243-1-rcampbell@nvidia.com
Fixes: 8763cb45ab967 ("mm/migrate: new memory migration helper for use with device memory")
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b358c6f12dc82364f6d317f8c8f1d794adbc3f5 ]
When CONFIG_MIGRATE_VMA_HELPER is enabled, migrate_vma() calls
migrate_vma_collect() which initializes a struct mm_walk but didn't
initialize mm_walk.pud_entry. (Found by code inspection) Use a C
structure initialization to make sure it is set to NULL.
Link: http://lkml.kernel.org/r/20190719233225.12243-1-rcampbell@nvidia.com
Fixes: 8763cb45ab967 ("mm/migrate: new memory migration helper for use with device memory")
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: at91: fix clk_offset for sama5d2
[ Upstream commit b1ac6704493fa14b5dc19eb6b69a73932361a131 ]
In SAMA5D2 datasheet, TWIHS_CWGR register rescription mentions clock
offset of 3 cycles (compared to 4 in eg. SAMA5D3).
Cc: stable@vger.kernel.org # 5.2.x
[needs applying to i2c-at91.c instead for earlier kernels]
Fixes: 0ef6f3213dac ("i2c: at91: add support for new alternative command mode")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1ac6704493fa14b5dc19eb6b69a73932361a131 ]
In SAMA5D2 datasheet, TWIHS_CWGR register rescription mentions clock
offset of 3 cycles (compared to 4 in eg. SAMA5D3).
Cc: stable@vger.kernel.org # 5.2.x
[needs applying to i2c-at91.c instead for earlier kernels]
Fixes: 0ef6f3213dac ("i2c: at91: add support for new alternative command mode")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: at91: disable TXRDY interrupt after sending data
[ Upstream commit d12e3aae160fb26b534c4496b211d6e60a5179ed ]
Driver was not disabling TXRDY interrupt after last TX byte.
This caused interrupt storm until transfer timeouts for slow
or broken device on the bus. The patch fixes the interrupt storm
on my SAMA5D2-based board.
Cc: stable@vger.kernel.org # 5.2.x
[v5.2 introduced file split; the patch should apply to i2c-at91.c before the split]
Fixes: fac368a04048 ("i2c: at91: add new driver")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tested-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d12e3aae160fb26b534c4496b211d6e60a5179ed ]
Driver was not disabling TXRDY interrupt after last TX byte.
This caused interrupt storm until transfer timeouts for slow
or broken device on the bus. The patch fixes the interrupt storm
on my SAMA5D2-based board.
Cc: stable@vger.kernel.org # 5.2.x
[v5.2 introduced file split; the patch should apply to i2c-at91.c before the split]
Fixes: fac368a04048 ("i2c: at91: add new driver")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tested-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
gpio: don't WARN() on NULL descs if gpiolib is disabled
[ Upstream commit ffe0bbabb0cffceceae07484fde1ec2a63b1537c ]
If gpiolib is disabled, we use the inline stubs from gpio/consumer.h
instead of regular definitions of GPIO API. The stubs for 'optional'
variants of gpiod_get routines return NULL in this case as if the
relevant GPIO wasn't found. This is correct so far.
Calling other (non-gpio_get) stubs from this header triggers a warning
because the GPIO descriptor couldn't have been requested. The warning
however is unconditional (WARN_ON(1)) and is emitted even if the passed
descriptor pointer is NULL.
We don't want to force the users of 'optional' gpio_get to check the
returned pointer before calling e.g. gpiod_set_value() so let's only
WARN on non-NULL descriptors.
Cc: stable@vger.kernel.org
Reported-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffe0bbabb0cffceceae07484fde1ec2a63b1537c ]
If gpiolib is disabled, we use the inline stubs from gpio/consumer.h
instead of regular definitions of GPIO API. The stubs for 'optional'
variants of gpiod_get routines return NULL in this case as if the
relevant GPIO wasn't found. This is correct so far.
Calling other (non-gpio_get) stubs from this header triggers a warning
because the GPIO descriptor couldn't have been requested. The warning
however is unconditional (WARN_ON(1)) and is emitted even if the passed
descriptor pointer is NULL.
We don't want to force the users of 'optional' gpio_get to check the
returned pointer before calling e.g. gpiod_set_value() so let's only
WARN on non-NULL descriptors.
Cc: stable@vger.kernel.org
Reported-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
iommu/iova: Remove stale cached32_node
[ Upstream commit 9eed17d37c77171cf5ffb95c4257f87df3cd4c8f ]
Since the cached32_node is allowed to be advanced above dma_32bit_pfn
(to provide a shortcut into the limited range), we need to be careful to
remove the to be freed node if it is the cached32_node.
[ 48.477773] BUG: KASAN: use-after-free in __cached_rbnode_delete_update+0x68/0x110
[ 48.477812] Read of size 8 at addr ffff88870fc19020 by task kworker/u8:1/37
[ 48.477843]
[ 48.477879] CPU: 1 PID: 37 Comm: kworker/u8:1 Tainted: G U 5.2.0+ #735
[ 48.477915] Hardware name: Intel Corporation NUC7i5BNK/NUC7i5BNB, BIOS BNKBL357.86A.0052.2017.0918.1346 09/18/2017
[ 48.478047] Workqueue: i915 __i915_gem_free_work [i915]
[ 48.478075] Call Trace:
[ 48.478111] dump_stack+0x5b/0x90
[ 48.478137] print_address_description+0x67/0x237
[ 48.478178] ? __cached_rbnode_delete_update+0x68/0x110
[ 48.478212] __kasan_report.cold.3+0x1c/0x38
[ 48.478240] ? __cached_rbnode_delete_update+0x68/0x110
[ 48.478280] ? __cached_rbnode_delete_update+0x68/0x110
[ 48.478308] __cached_rbnode_delete_update+0x68/0x110
[ 48.478344] private_free_iova+0x2b/0x60
[ 48.478378] iova_magazine_free_pfns+0x46/0xa0
[ 48.478403] free_iova_fast+0x277/0x340
[ 48.478443] fq_ring_free+0x15a/0x1a0
[ 48.478473] queue_iova+0x19c/0x1f0
[ 48.478597] cleanup_page_dma.isra.64+0x62/0xb0 [i915]
[ 48.478712] __gen8_ppgtt_cleanup+0x63/0x80 [i915]
[ 48.478826] __gen8_ppgtt_cleanup+0x42/0x80 [i915]
[ 48.478940] __gen8_ppgtt_clear+0x433/0x4b0 [i915]
[ 48.479053] __gen8_ppgtt_clear+0x462/0x4b0 [i915]
[ 48.479081] ? __sg_free_table+0x9e/0xf0
[ 48.479116] ? kfree+0x7f/0x150
[ 48.479234] i915_vma_unbind+0x1e2/0x240 [i915]
[ 48.479352] i915_vma_destroy+0x3a/0x280 [i915]
[ 48.479465] __i915_gem_free_objects+0xf0/0x2d0 [i915]
[ 48.479579] __i915_gem_free_work+0x41/0xa0 [i915]
[ 48.479607] process_one_work+0x495/0x710
[ 48.479642] worker_thread+0x4c7/0x6f0
[ 48.479687] ? process_one_work+0x710/0x710
[ 48.479724] kthread+0x1b2/0x1d0
[ 48.479774] ? kthread_create_worker_on_cpu+0xa0/0xa0
[ 48.479820] ret_from_fork+0x1f/0x30
[ 48.479864]
[ 48.479907] Allocated by task 631:
[ 48.479944] save_stack+0x19/0x80
[ 48.479994] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 48.480038] kmem_cache_alloc+0x91/0xf0
[ 48.480082] alloc_iova+0x2b/0x1e0
[ 48.480125] alloc_iova_fast+0x58/0x376
[ 48.480166] intel_alloc_iova+0x90/0xc0
[ 48.480214] intel_map_sg+0xde/0x1f0
[ 48.480343] i915_gem_gtt_prepare_pages+0xb8/0x170 [i915]
[ 48.480465] huge_get_pages+0x232/0x2b0 [i915]
[ 48.480590] ____i915_gem_object_get_pages+0x40/0xb0 [i915]
[ 48.480712] __i915_gem_object_get_pages+0x90/0xa0 [i915]
[ 48.480834] i915_gem_object_prepare_write+0x2d6/0x330 [i915]
[ 48.480955] create_test_object.isra.54+0x1a9/0x3e0 [i915]
[ 48.481075] igt_shared_ctx_exec+0x365/0x3c0 [i915]
[ 48.481210] __i915_subtests.cold.4+0x30/0x92 [i915]
[ 48.481341] __run_selftests.cold.3+0xa9/0x119 [i915]
[ 48.481466] i915_live_selftests+0x3c/0x70 [i915]
[ 48.481583] i915_pci_probe+0xe7/0x220 [i915]
[ 48.481620] pci_device_probe+0xe0/0x180
[ 48.481665] really_probe+0x163/0x4e0
[ 48.481710] device_driver_attach+0x85/0x90
[ 48.481750] __driver_attach+0xa5/0x180
[ 48.481796] bus_for_each_dev+0xda/0x130
[ 48.481831] bus_add_driver+0x205/0x2e0
[ 48.481882] driver_register+0xca/0x140
[ 48.481927] do_one_initcall+0x6c/0x1af
[ 48.481970] do_init_module+0x106/0x350
[ 48.482010] load_module+0x3d2c/0x3ea0
[ 48.482058] __do_sys_finit_module+0x110/0x180
[ 48.482102] do_syscall_64+0x62/0x1f0
[ 48.482147] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.482190]
[ 48.482224] Freed by task 37:
[ 48.482273] save_stack+0x19/0x80
[ 48.482318] __kasan_slab_free+0x12e/0x180
[ 48.482363] kmem_cache_free+0x70/0x140
[ 48.482406] __free_iova+0x1d/0x30
[ 48.482445] fq_ring_free+0x15a/0x1a0
[ 48.482490] queue_iova+0x19c/0x1f0
[ 48.482624] cleanup_page_dma.isra.64+0x62/0xb0 [i915]
[ 48.482749] __gen8_ppgtt_cleanup+0x63/0x80 [i915]
[ 48.482873] __gen8_ppgtt_cleanup+0x42/0x80 [i915]
[ 48.482999] __gen8_ppgtt_clear+0x433/0x4b0 [i915]
[ 48.483123] __gen8_ppgtt_clear+0x462/0x4b0 [i915]
[ 48.483250] i915_vma_unbind+0x1e2/0x240 [i915]
[ 48.483378] i915_vma_destroy+0x3a/0x280 [i915]
[ 48.483500] __i915_gem_free_objects+0xf0/0x2d0 [i915]
[ 48.483622] __i915_gem_free_work+0x41/0xa0 [i915]
[ 48.483659] process_one_work+0x495/0x710
[ 48.483704] worker_thread+0x4c7/0x6f0
[ 48.483748] kthread+0x1b2/0x1d0
[ 48.483787] ret_from_fork+0x1f/0x30
[ 48.483831]
[ 48.483868] The buggy address belongs to the object at ffff88870fc19000
[ 48.483868] which belongs to the cache iommu_iova of size 40
[ 48.483920] The buggy address is located 32 bytes inside of
[ 48.483920] 40-byte region [ffff88870fc19000, ffff88870fc19028)
[ 48.483964] The buggy address belongs to the page:
[ 48.484006] page:ffffea001c3f0600 refcount:1 mapcount:0 mapping:ffff8888181a91c0 index:0x0 compound_mapcount: 0
[ 48.484045] flags: 0x8000000000010200(slab|head)
[ 48.484096] raw: 8000000000010200 ffffea001c421a08 ffffea001c447e88 ffff8888181a91c0
[ 48.484141] raw: 0000000000000000 0000000000120012 00000001ffffffff 0000000000000000
[ 48.484188] page dumped because: kasan: bad access detected
[ 48.484230]
[ 48.484265] Memory state around the buggy address:
[ 48.484314] ffff88870fc18f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 48.484361] ffff88870fc18f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 48.484406] >ffff88870fc19000: fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc
[ 48.484451] ^
[ 48.484494] ffff88870fc19080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 48.484530] ffff88870fc19100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108602
Fixes: e60aa7b53845 ("iommu/iova: Extend rbtree node caching")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eed17d37c77171cf5ffb95c4257f87df3cd4c8f ]
Since the cached32_node is allowed to be advanced above dma_32bit_pfn
(to provide a shortcut into the limited range), we need to be careful to
remove the to be freed node if it is the cached32_node.
[ 48.477773] BUG: KASAN: use-after-free in __cached_rbnode_delete_update+0x68/0x110
[ 48.477812] Read of size 8 at addr ffff88870fc19020 by task kworker/u8:1/37
[ 48.477843]
[ 48.477879] CPU: 1 PID: 37 Comm: kworker/u8:1 Tainted: G U 5.2.0+ #735
[ 48.477915] Hardware name: Intel Corporation NUC7i5BNK/NUC7i5BNB, BIOS BNKBL357.86A.0052.2017.0918.1346 09/18/2017
[ 48.478047] Workqueue: i915 __i915_gem_free_work [i915]
[ 48.478075] Call Trace:
[ 48.478111] dump_stack+0x5b/0x90
[ 48.478137] print_address_description+0x67/0x237
[ 48.478178] ? __cached_rbnode_delete_update+0x68/0x110
[ 48.478212] __kasan_report.cold.3+0x1c/0x38
[ 48.478240] ? __cached_rbnode_delete_update+0x68/0x110
[ 48.478280] ? __cached_rbnode_delete_update+0x68/0x110
[ 48.478308] __cached_rbnode_delete_update+0x68/0x110
[ 48.478344] private_free_iova+0x2b/0x60
[ 48.478378] iova_magazine_free_pfns+0x46/0xa0
[ 48.478403] free_iova_fast+0x277/0x340
[ 48.478443] fq_ring_free+0x15a/0x1a0
[ 48.478473] queue_iova+0x19c/0x1f0
[ 48.478597] cleanup_page_dma.isra.64+0x62/0xb0 [i915]
[ 48.478712] __gen8_ppgtt_cleanup+0x63/0x80 [i915]
[ 48.478826] __gen8_ppgtt_cleanup+0x42/0x80 [i915]
[ 48.478940] __gen8_ppgtt_clear+0x433/0x4b0 [i915]
[ 48.479053] __gen8_ppgtt_clear+0x462/0x4b0 [i915]
[ 48.479081] ? __sg_free_table+0x9e/0xf0
[ 48.479116] ? kfree+0x7f/0x150
[ 48.479234] i915_vma_unbind+0x1e2/0x240 [i915]
[ 48.479352] i915_vma_destroy+0x3a/0x280 [i915]
[ 48.479465] __i915_gem_free_objects+0xf0/0x2d0 [i915]
[ 48.479579] __i915_gem_free_work+0x41/0xa0 [i915]
[ 48.479607] process_one_work+0x495/0x710
[ 48.479642] worker_thread+0x4c7/0x6f0
[ 48.479687] ? process_one_work+0x710/0x710
[ 48.479724] kthread+0x1b2/0x1d0
[ 48.479774] ? kthread_create_worker_on_cpu+0xa0/0xa0
[ 48.479820] ret_from_fork+0x1f/0x30
[ 48.479864]
[ 48.479907] Allocated by task 631:
[ 48.479944] save_stack+0x19/0x80
[ 48.479994] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 48.480038] kmem_cache_alloc+0x91/0xf0
[ 48.480082] alloc_iova+0x2b/0x1e0
[ 48.480125] alloc_iova_fast+0x58/0x376
[ 48.480166] intel_alloc_iova+0x90/0xc0
[ 48.480214] intel_map_sg+0xde/0x1f0
[ 48.480343] i915_gem_gtt_prepare_pages+0xb8/0x170 [i915]
[ 48.480465] huge_get_pages+0x232/0x2b0 [i915]
[ 48.480590] ____i915_gem_object_get_pages+0x40/0xb0 [i915]
[ 48.480712] __i915_gem_object_get_pages+0x90/0xa0 [i915]
[ 48.480834] i915_gem_object_prepare_write+0x2d6/0x330 [i915]
[ 48.480955] create_test_object.isra.54+0x1a9/0x3e0 [i915]
[ 48.481075] igt_shared_ctx_exec+0x365/0x3c0 [i915]
[ 48.481210] __i915_subtests.cold.4+0x30/0x92 [i915]
[ 48.481341] __run_selftests.cold.3+0xa9/0x119 [i915]
[ 48.481466] i915_live_selftests+0x3c/0x70 [i915]
[ 48.481583] i915_pci_probe+0xe7/0x220 [i915]
[ 48.481620] pci_device_probe+0xe0/0x180
[ 48.481665] really_probe+0x163/0x4e0
[ 48.481710] device_driver_attach+0x85/0x90
[ 48.481750] __driver_attach+0xa5/0x180
[ 48.481796] bus_for_each_dev+0xda/0x130
[ 48.481831] bus_add_driver+0x205/0x2e0
[ 48.481882] driver_register+0xca/0x140
[ 48.481927] do_one_initcall+0x6c/0x1af
[ 48.481970] do_init_module+0x106/0x350
[ 48.482010] load_module+0x3d2c/0x3ea0
[ 48.482058] __do_sys_finit_module+0x110/0x180
[ 48.482102] do_syscall_64+0x62/0x1f0
[ 48.482147] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.482190]
[ 48.482224] Freed by task 37:
[ 48.482273] save_stack+0x19/0x80
[ 48.482318] __kasan_slab_free+0x12e/0x180
[ 48.482363] kmem_cache_free+0x70/0x140
[ 48.482406] __free_iova+0x1d/0x30
[ 48.482445] fq_ring_free+0x15a/0x1a0
[ 48.482490] queue_iova+0x19c/0x1f0
[ 48.482624] cleanup_page_dma.isra.64+0x62/0xb0 [i915]
[ 48.482749] __gen8_ppgtt_cleanup+0x63/0x80 [i915]
[ 48.482873] __gen8_ppgtt_cleanup+0x42/0x80 [i915]
[ 48.482999] __gen8_ppgtt_clear+0x433/0x4b0 [i915]
[ 48.483123] __gen8_ppgtt_clear+0x462/0x4b0 [i915]
[ 48.483250] i915_vma_unbind+0x1e2/0x240 [i915]
[ 48.483378] i915_vma_destroy+0x3a/0x280 [i915]
[ 48.483500] __i915_gem_free_objects+0xf0/0x2d0 [i915]
[ 48.483622] __i915_gem_free_work+0x41/0xa0 [i915]
[ 48.483659] process_one_work+0x495/0x710
[ 48.483704] worker_thread+0x4c7/0x6f0
[ 48.483748] kthread+0x1b2/0x1d0
[ 48.483787] ret_from_fork+0x1f/0x30
[ 48.483831]
[ 48.483868] The buggy address belongs to the object at ffff88870fc19000
[ 48.483868] which belongs to the cache iommu_iova of size 40
[ 48.483920] The buggy address is located 32 bytes inside of
[ 48.483920] 40-byte region [ffff88870fc19000, ffff88870fc19028)
[ 48.483964] The buggy address belongs to the page:
[ 48.484006] page:ffffea001c3f0600 refcount:1 mapcount:0 mapping:ffff8888181a91c0 index:0x0 compound_mapcount: 0
[ 48.484045] flags: 0x8000000000010200(slab|head)
[ 48.484096] raw: 8000000000010200 ffffea001c421a08 ffffea001c447e88 ffff8888181a91c0
[ 48.484141] raw: 0000000000000000 0000000000120012 00000001ffffffff 0000000000000000
[ 48.484188] page dumped because: kasan: bad access detected
[ 48.484230]
[ 48.484265] Memory state around the buggy address:
[ 48.484314] ffff88870fc18f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 48.484361] ffff88870fc18f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 48.484406] >ffff88870fc19000: fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc
[ 48.484451] ^
[ 48.484494] ffff88870fc19080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 48.484530] ffff88870fc19100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108602
Fixes: e60aa7b53845 ("iommu/iova: Extend rbtree node caching")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
powerpc/mm: Limit rma_size to 1TB when running without HV mode
[ Upstream commit da0ef93310e67ae6902efded60b6724dab27a5d1 ]
The virtual real mode addressing (VRMA) mechanism is used when a
partition is using HPT (Hash Page Table) translation and performs real
mode accesses (MSR[IR|DR] = 0) in non-hypervisor mode. In this mode
effective address bits 0:23 are treated as zero (i.e. the access is
aliased to 0) and the access is performed using an implicit 1TB SLB
entry.
The size of the RMA (Real Memory Area) is communicated to the guest as
the size of the first memory region in the device tree. And because of
the mechanism described above can be expected to not exceed 1TB. In
the event that the host erroneously represents the RMA as being larger
than 1TB, guest accesses in real mode to memory addresses above 1TB
will be aliased down to below 1TB. This means that a memory access
performed in real mode may differ to one performed in virtual mode for
the same memory address, which would likely have unintended
consequences.
To avoid this outcome have the guest explicitly limit the size of the
RMA to the current maximum, which is 1TB. This means that even if the
first memory block is larger than 1TB, only the first 1TB should be
accessed in real mode.
Fixes: c610d65c0ad0 ("powerpc/pseries: lift RTAS limit for hash")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Tested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190710052018.14628-1-sjitindarsingh@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da0ef93310e67ae6902efded60b6724dab27a5d1 ]
The virtual real mode addressing (VRMA) mechanism is used when a
partition is using HPT (Hash Page Table) translation and performs real
mode accesses (MSR[IR|DR] = 0) in non-hypervisor mode. In this mode
effective address bits 0:23 are treated as zero (i.e. the access is
aliased to 0) and the access is performed using an implicit 1TB SLB
entry.
The size of the RMA (Real Memory Area) is communicated to the guest as
the size of the first memory region in the device tree. And because of
the mechanism described above can be expected to not exceed 1TB. In
the event that the host erroneously represents the RMA as being larger
than 1TB, guest accesses in real mode to memory addresses above 1TB
will be aliased down to below 1TB. This means that a memory access
performed in real mode may differ to one performed in virtual mode for
the same memory address, which would likely have unintended
consequences.
To avoid this outcome have the guest explicitly limit the size of the
RMA to the current maximum, which is 1TB. This means that even if the
first memory block is larger than 1TB, only the first 1TB should be
accessed in real mode.
Fixes: c610d65c0ad0 ("powerpc/pseries: lift RTAS limit for hash")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Tested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190710052018.14628-1-sjitindarsingh@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
ALSA: hda - Fix intermittent CORB/RIRB stall on Intel chips
[ Upstream commit 2756d9143aa517b97961e85412882b8ce31371a6 ]
It turned out that the recent Intel HD-audio controller chips show a
significant stall during the system PM resume intermittently. It
doesn't happen so often and usually it may read back successfully
after one or more seconds, but in some rare worst cases the driver
went into fallback mode.
After trial-and-error, we found out that the communication stall seems
covered by issuing the sync after each verb write, as already done for
AMD and other chipsets. So this patch enables the write-sync flag for
the recent Intel chips, Skylake and onward, as a workaround.
Also, since Broxton and co have the very same driver flags as Skylake,
refer to the Skylake driver flags instead of defining the same
contents again for simplification.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201901
Reported-and-tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2756d9143aa517b97961e85412882b8ce31371a6 ]
It turned out that the recent Intel HD-audio controller chips show a
significant stall during the system PM resume intermittently. It
doesn't happen so often and usually it may read back successfully
after one or more seconds, but in some rare worst cases the driver
went into fallback mode.
After trial-and-error, we found out that the communication stall seems
covered by issuing the sync after each verb write, as already done for
AMD and other chipsets. So this patch enables the write-sync flag for
the recent Intel chips, Skylake and onward, as a workaround.
Also, since Broxton and co have the very same driver flags as Skylake,
refer to the Skylake driver flags instead of defining the same
contents again for simplification.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201901
Reported-and-tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
drm/panel: Add support for Armadeus ST0700 Adapt
[ Upstream commit c479450f61c7f1f248c9a54aedacd2a6ca521ff8 ]
This patch adds support for the Armadeus ST0700 Adapt. It comes with a
Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT and an adapter board so
that it can be connected on the TFT header of Armadeus Dev boards.
Cc: stable@vger.kernel.org # v4.19
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507152713.27494-1-sebastien.szymanski@armadeus.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c479450f61c7f1f248c9a54aedacd2a6ca521ff8 ]
This patch adds support for the Armadeus ST0700 Adapt. It comes with a
Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT and an adapter board so
that it can be connected on the TFT header of Armadeus Dev boards.
Cc: stable@vger.kernel.org # v4.19
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507152713.27494-1-sebastien.szymanski@armadeus.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
dm thin metadata: check if in fail_io mode when setting needs_check
[ Upstream commit 54fa16ee532705985e6c946da455856f18f63ee1 ]
Check if in fail_io mode at start of dm_pool_metadata_set_needs_check().
Otherwise dm_pool_metadata_set_needs_check()'s superblock_lock() can
crash in dm_bm_write_lock() while accessing the block manager object
that was previously destroyed as part of a failed
dm_pool_abort_metadata() that ultimately set fail_io to begin with.
Also, update DMERR() message to more accurately describe
superblock_lock() failure.
Cc: stable@vger.kernel.org
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54fa16ee532705985e6c946da455856f18f63ee1 ]
Check if in fail_io mode at start of dm_pool_metadata_set_needs_check().
Otherwise dm_pool_metadata_set_needs_check()'s superblock_lock() can
crash in dm_bm_write_lock() while accessing the block manager object
that was previously destroyed as part of a failed
dm_pool_abort_metadata() that ultimately set fail_io to begin with.
Also, update DMERR() message to more accurately describe
superblock_lock() failure.
Cc: stable@vger.kernel.org
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
pstore: Fix double-free in pstore_mkfile() failure path
[ Upstream commit 4c6d80e1144bdf48cae6b602ae30d41f3e5c76a9 ]
The pstore_mkfile() function is passed a pointer to a struct
pstore_record. On success it consumes this 'record' pointer and
references it from the created inode.
On failure, however, it may or may not free the record. There are even
two different code paths which return -ENOMEM -- one of which does and
the other doesn't free the record.
Make the behaviour deterministic by never consuming and freeing the
record when returning failure, allowing the caller to do the cleanup
consistently.
Signed-off-by: Norbert Manthey <nmanthey@amazon.de>
Link: https://lore.kernel.org/r/1562331960-26198-1-git-send-email-nmanthey@amazon.de
Fixes: 83f70f0769ddd ("pstore: Do not duplicate record metadata")
Fixes: 1dfff7dd67d1a ("pstore: Pass record contents instead of copying")
Cc: stable@vger.kernel.org
[kees: also move "private" allocation location, rename inode cleanup label]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c6d80e1144bdf48cae6b602ae30d41f3e5c76a9 ]
The pstore_mkfile() function is passed a pointer to a struct
pstore_record. On success it consumes this 'record' pointer and
references it from the created inode.
On failure, however, it may or may not free the record. There are even
two different code paths which return -ENOMEM -- one of which does and
the other doesn't free the record.
Make the behaviour deterministic by never consuming and freeing the
record when returning failure, allowing the caller to do the cleanup
consistently.
Signed-off-by: Norbert Manthey <nmanthey@amazon.de>
Link: https://lore.kernel.org/r/1562331960-26198-1-git-send-email-nmanthey@amazon.de
Fixes: 83f70f0769ddd ("pstore: Do not duplicate record metadata")
Fixes: 1dfff7dd67d1a ("pstore: Pass record contents instead of copying")
Cc: stable@vger.kernel.org
[kees: also move "private" allocation location, rename inode cleanup label]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
resource: fix locking in find_next_iomem_res()
[ Upstream commit 49f17c26c123b60fd1c74629eef077740d16ffc2 ]
Since resources can be removed, locking should ensure that the resource
is not removed while accessing it. However, find_next_iomem_res() does
not hold the lock while copying the data of the resource.
Keep holding the lock while the data is copied. While at it, change the
return value to a more informative value. It is disregarded by the
callers.
[akpm@linux-foundation.org: fix find_next_iomem_res() documentation]
Link: http://lkml.kernel.org/r/20190613045903.4922-2-namit@vmware.com
Fixes: ff3cc952d3f00 ("resource: Add remove_resource interface")
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49f17c26c123b60fd1c74629eef077740d16ffc2 ]
Since resources can be removed, locking should ensure that the resource
is not removed while accessing it. However, find_next_iomem_res() does
not hold the lock while copying the data of the resource.
Keep holding the lock while the data is copied. While at it, change the
return value to a more informative value. It is disregarded by the
callers.
[akpm@linux-foundation.org: fix find_next_iomem_res() documentation]
Link: http://lkml.kernel.org/r/20190613045903.4922-2-namit@vmware.com
Fixes: ff3cc952d3f00 ("resource: Add remove_resource interface")
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
resource: Fix find_next_iomem_res() iteration issue
[ Upstream commit 010a93bf97c72f43aac664d0a685942f83d1a103 ]
Previously find_next_iomem_res() used "*res" as both an input parameter for
the range to search and the type of resource to search for, and an output
parameter for the resource we found, which makes the interface confusing.
The current callers use find_next_iomem_res() incorrectly because they
allocate a single struct resource and use it for repeated calls to
find_next_iomem_res(). When find_next_iomem_res() returns a resource, it
overwrites the start, end, flags, and desc members of the struct. If we
call find_next_iomem_res() again, we must update or restore these fields.
The previous code restored res.start and res.end, but not res.flags or
res.desc.
Since the callers did not restore res.flags, if they searched for flags
IORESOURCE_MEM | IORESOURCE_BUSY and found a resource with flags
IORESOURCE_MEM | IORESOURCE_BUSY | IORESOURCE_SYSRAM, the next search would
incorrectly skip resources unless they were also marked as
IORESOURCE_SYSRAM.
Fix this by restructuring the interface so it takes explicit "start, end,
flags" parameters and uses "*res" only as an output parameter.
Based on a patch by Lianbo Jiang <lijiang@redhat.com>.
[ bp: While at it:
- make comments kernel-doc style.
-
Originally-by: http://lore.kernel.org/lkml/20180921073211.20097-2-lijiang@redhat.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Brijesh Singh <brijesh.singh@amd.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Lianbo Jiang <lijiang@redhat.com>
CC: Takashi Iwai <tiwai@suse.de>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Vivek Goyal <vgoyal@redhat.com>
CC: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
CC: bhe@redhat.com
CC: dan.j.williams@intel.com
CC: dyoung@redhat.com
CC: kexec@lists.infradead.org
CC: mingo@redhat.com
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/153805812916.1157.177580438135143788.stgit@bhelgaas-glaptop.roam.corp.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 010a93bf97c72f43aac664d0a685942f83d1a103 ]
Previously find_next_iomem_res() used "*res" as both an input parameter for
the range to search and the type of resource to search for, and an output
parameter for the resource we found, which makes the interface confusing.
The current callers use find_next_iomem_res() incorrectly because they
allocate a single struct resource and use it for repeated calls to
find_next_iomem_res(). When find_next_iomem_res() returns a resource, it
overwrites the start, end, flags, and desc members of the struct. If we
call find_next_iomem_res() again, we must update or restore these fields.
The previous code restored res.start and res.end, but not res.flags or
res.desc.
Since the callers did not restore res.flags, if they searched for flags
IORESOURCE_MEM | IORESOURCE_BUSY and found a resource with flags
IORESOURCE_MEM | IORESOURCE_BUSY | IORESOURCE_SYSRAM, the next search would
incorrectly skip resources unless they were also marked as
IORESOURCE_SYSRAM.
Fix this by restructuring the interface so it takes explicit "start, end,
flags" parameters and uses "*res" only as an output parameter.
Based on a patch by Lianbo Jiang <lijiang@redhat.com>.
[ bp: While at it:
- make comments kernel-doc style.
-
Originally-by: http://lore.kernel.org/lkml/20180921073211.20097-2-lijiang@redhat.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Brijesh Singh <brijesh.singh@amd.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Lianbo Jiang <lijiang@redhat.com>
CC: Takashi Iwai <tiwai@suse.de>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Vivek Goyal <vgoyal@redhat.com>
CC: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
CC: bhe@redhat.com
CC: dan.j.williams@intel.com
CC: dyoung@redhat.com
CC: kexec@lists.infradead.org
CC: mingo@redhat.com
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/153805812916.1157.177580438135143788.stgit@bhelgaas-glaptop.roam.corp.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
resource: Include resource end in walk_*() interfaces
[ Upstream commit a98959fdbda1849a01b2150bb635ed559ec06700 ]
find_next_iomem_res() finds an iomem resource that covers part of a range
described by "start, end". All callers expect that range to be inclusive,
i.e., both start and end are included, but find_next_iomem_res() doesn't
handle the end address correctly.
If it finds an iomem resource that contains exactly the end address, it
skips it, e.g., if "start, end" is [0x0-0x10000] and there happens to be an
iomem resource [mem 0x10000-0x10000] (the single byte at 0x10000), we skip
it:
find_next_iomem_res(...)
{
start = 0x0;
end = 0x10000;
for (p = next_resource(...)) {
# p->start = 0x10000;
# p->end = 0x10000;
# we *should* return this resource, but this condition is false:
if ((p->end >= start) && (p->start < end))
break;
Adjust find_next_iomem_res() so it allows a resource that includes the
single byte at the end of the range. This is a corner case that we
probably don't see in practice.
Fixes: 58c1b5b07907 ("[PATCH] memory hotadd fixes: find_next_system_ram catch range fix")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Brijesh Singh <brijesh.singh@amd.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Lianbo Jiang <lijiang@redhat.com>
CC: Takashi Iwai <tiwai@suse.de>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Vivek Goyal <vgoyal@redhat.com>
CC: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
CC: bhe@redhat.com
CC: dan.j.williams@intel.com
CC: dyoung@redhat.com
CC: kexec@lists.infradead.org
CC: mingo@redhat.com
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/153805812254.1157.16736368485811773752.stgit@bhelgaas-glaptop.roam.corp.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a98959fdbda1849a01b2150bb635ed559ec06700 ]
find_next_iomem_res() finds an iomem resource that covers part of a range
described by "start, end". All callers expect that range to be inclusive,
i.e., both start and end are included, but find_next_iomem_res() doesn't
handle the end address correctly.
If it finds an iomem resource that contains exactly the end address, it
skips it, e.g., if "start, end" is [0x0-0x10000] and there happens to be an
iomem resource [mem 0x10000-0x10000] (the single byte at 0x10000), we skip
it:
find_next_iomem_res(...)
{
start = 0x0;
end = 0x10000;
for (p = next_resource(...)) {
# p->start = 0x10000;
# p->end = 0x10000;
# we *should* return this resource, but this condition is false:
if ((p->end >= start) && (p->start < end))
break;
Adjust find_next_iomem_res() so it allows a resource that includes the
single byte at the end of the range. This is a corner case that we
probably don't see in practice.
Fixes: 58c1b5b07907 ("[PATCH] memory hotadd fixes: find_next_system_ram catch range fix")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Brijesh Singh <brijesh.singh@amd.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Lianbo Jiang <lijiang@redhat.com>
CC: Takashi Iwai <tiwai@suse.de>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Vivek Goyal <vgoyal@redhat.com>
CC: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
CC: bhe@redhat.com
CC: dan.j.williams@intel.com
CC: dyoung@redhat.com
CC: kexec@lists.infradead.org
CC: mingo@redhat.com
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/153805812254.1157.16736368485811773752.stgit@bhelgaas-glaptop.roam.corp.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
btrfs: correctly validate compression type
[ Upstream commit aa53e3bfac7205fb3a8815ac1c937fd6ed01b41e ]
Nikolay reported the following KASAN splat when running btrfs/048:
[ 1843.470920] ==================================================================
[ 1843.471971] BUG: KASAN: slab-out-of-bounds in strncmp+0x66/0xb0
[ 1843.472775] Read of size 1 at addr ffff888111e369e2 by task btrfs/3979
[ 1843.473904] CPU: 3 PID: 3979 Comm: btrfs Not tainted 5.2.0-rc3-default #536
[ 1843.475009] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 1843.476322] Call Trace:
[ 1843.476674] dump_stack+0x7c/0xbb
[ 1843.477132] ? strncmp+0x66/0xb0
[ 1843.477587] print_address_description+0x114/0x320
[ 1843.478256] ? strncmp+0x66/0xb0
[ 1843.478740] ? strncmp+0x66/0xb0
[ 1843.479185] __kasan_report+0x14e/0x192
[ 1843.479759] ? strncmp+0x66/0xb0
[ 1843.480209] kasan_report+0xe/0x20
[ 1843.480679] strncmp+0x66/0xb0
[ 1843.481105] prop_compression_validate+0x24/0x70
[ 1843.481798] btrfs_xattr_handler_set_prop+0x65/0x160
[ 1843.482509] __vfs_setxattr+0x71/0x90
[ 1843.483012] __vfs_setxattr_noperm+0x84/0x130
[ 1843.483606] vfs_setxattr+0xac/0xb0
[ 1843.484085] setxattr+0x18c/0x230
[ 1843.484546] ? vfs_setxattr+0xb0/0xb0
[ 1843.485048] ? __mod_node_page_state+0x1f/0xa0
[ 1843.485672] ? _raw_spin_unlock+0x24/0x40
[ 1843.486233] ? __handle_mm_fault+0x988/0x1290
[ 1843.486823] ? lock_acquire+0xb4/0x1e0
[ 1843.487330] ? lock_acquire+0xb4/0x1e0
[ 1843.487842] ? mnt_want_write_file+0x3c/0x80
[ 1843.488442] ? debug_lockdep_rcu_enabled+0x22/0x40
[ 1843.489089] ? rcu_sync_lockdep_assert+0xe/0x70
[ 1843.489707] ? __sb_start_write+0x158/0x200
[ 1843.490278] ? mnt_want_write_file+0x3c/0x80
[ 1843.490855] ? __mnt_want_write+0x98/0xe0
[ 1843.491397] __x64_sys_fsetxattr+0xba/0xe0
[ 1843.492201] ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 1843.493201] do_syscall_64+0x6c/0x230
[ 1843.493988] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1843.495041] RIP: 0033:0x7fa7a8a7707a
[ 1843.495819] Code: 48 8b 0d 21 de 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 be 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d ee dd 2b 00 f7 d8 64 89 01 48
[ 1843.499203] RSP: 002b:00007ffcb73bca38 EFLAGS: 00000202 ORIG_RAX: 00000000000000be
[ 1843.500210] RAX: ffffffffffffffda RBX: 00007ffcb73bda9d RCX: 00007fa7a8a7707a
[ 1843.501170] RDX: 00007ffcb73bda9d RSI: 00000000006dc050 RDI: 0000000000000003
[ 1843.502152] RBP: 00000000006dc050 R08: 0000000000000000 R09: 0000000000000000
[ 1843.503109] R10: 0000000000000002 R11: 0000000000000202 R12: 00007ffcb73bda91
[ 1843.504055] R13: 0000000000000003 R14: 00007ffcb73bda82 R15: ffffffffffffffff
[ 1843.505268] Allocated by task 3979:
[ 1843.505771] save_stack+0x19/0x80
[ 1843.506211] __kasan_kmalloc.constprop.5+0xa0/0xd0
[ 1843.506836] setxattr+0xeb/0x230
[ 1843.507264] __x64_sys_fsetxattr+0xba/0xe0
[ 1843.507886] do_syscall_64+0x6c/0x230
[ 1843.508429] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1843.509558] Freed by task 0:
[ 1843.510188] (stack is not available)
[ 1843.511309] The buggy address belongs to the object at ffff888111e369e0
which belongs to the cache kmalloc-8 of size 8
[ 1843.514095] The buggy address is located 2 bytes inside of
8-byte region [ffff888111e369e0, ffff888111e369e8)
[ 1843.516524] The buggy address belongs to the page:
[ 1843.517561] page:ffff88813f478d80 refcount:1 mapcount:0 mapping:ffff88811940c300 index:0xffff888111e373b8 compound_mapcount: 0
[ 1843.519993] flags: 0x4404000010200(slab|head)
[ 1843.520951] raw: 0004404000010200 ffff88813f48b008 ffff888119403d50 ffff88811940c300
[ 1843.522616] raw: ffff888111e373b8 000000000016000f 00000001ffffffff 0000000000000000
[ 1843.524281] page dumped because: kasan: bad access detected
[ 1843.525936] Memory state around the buggy address:
[ 1843.526975] ffff888111e36880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.528479] ffff888111e36900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.530138] >ffff888111e36980: fc fc fc fc fc fc fc fc fc fc fc fc 02 fc fc fc
[ 1843.531877] ^
[ 1843.533287] ffff888111e36a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.534874] ffff888111e36a80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.536468] ==================================================================
This is caused by supplying a too short compression value ('lz') in the
test-case and comparing it to 'lzo' with strncmp() and a length of 3.
strncmp() read past the 'lz' when looking for the 'o' and thus caused an
out-of-bounds read.
Introduce a new check 'btrfs_compress_is_valid_type()' which not only
checks the user-supplied value against known compression types, but also
employs checks for too short values.
Reported-by: Nikolay Borisov <nborisov@suse.com>
Fixes: 272e5326c783 ("btrfs: prop: fix vanished compression property after failed set")
CC: stable@vger.kernel.org # 5.1+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa53e3bfac7205fb3a8815ac1c937fd6ed01b41e ]
Nikolay reported the following KASAN splat when running btrfs/048:
[ 1843.470920] ==================================================================
[ 1843.471971] BUG: KASAN: slab-out-of-bounds in strncmp+0x66/0xb0
[ 1843.472775] Read of size 1 at addr ffff888111e369e2 by task btrfs/3979
[ 1843.473904] CPU: 3 PID: 3979 Comm: btrfs Not tainted 5.2.0-rc3-default #536
[ 1843.475009] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 1843.476322] Call Trace:
[ 1843.476674] dump_stack+0x7c/0xbb
[ 1843.477132] ? strncmp+0x66/0xb0
[ 1843.477587] print_address_description+0x114/0x320
[ 1843.478256] ? strncmp+0x66/0xb0
[ 1843.478740] ? strncmp+0x66/0xb0
[ 1843.479185] __kasan_report+0x14e/0x192
[ 1843.479759] ? strncmp+0x66/0xb0
[ 1843.480209] kasan_report+0xe/0x20
[ 1843.480679] strncmp+0x66/0xb0
[ 1843.481105] prop_compression_validate+0x24/0x70
[ 1843.481798] btrfs_xattr_handler_set_prop+0x65/0x160
[ 1843.482509] __vfs_setxattr+0x71/0x90
[ 1843.483012] __vfs_setxattr_noperm+0x84/0x130
[ 1843.483606] vfs_setxattr+0xac/0xb0
[ 1843.484085] setxattr+0x18c/0x230
[ 1843.484546] ? vfs_setxattr+0xb0/0xb0
[ 1843.485048] ? __mod_node_page_state+0x1f/0xa0
[ 1843.485672] ? _raw_spin_unlock+0x24/0x40
[ 1843.486233] ? __handle_mm_fault+0x988/0x1290
[ 1843.486823] ? lock_acquire+0xb4/0x1e0
[ 1843.487330] ? lock_acquire+0xb4/0x1e0
[ 1843.487842] ? mnt_want_write_file+0x3c/0x80
[ 1843.488442] ? debug_lockdep_rcu_enabled+0x22/0x40
[ 1843.489089] ? rcu_sync_lockdep_assert+0xe/0x70
[ 1843.489707] ? __sb_start_write+0x158/0x200
[ 1843.490278] ? mnt_want_write_file+0x3c/0x80
[ 1843.490855] ? __mnt_want_write+0x98/0xe0
[ 1843.491397] __x64_sys_fsetxattr+0xba/0xe0
[ 1843.492201] ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 1843.493201] do_syscall_64+0x6c/0x230
[ 1843.493988] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1843.495041] RIP: 0033:0x7fa7a8a7707a
[ 1843.495819] Code: 48 8b 0d 21 de 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 be 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d ee dd 2b 00 f7 d8 64 89 01 48
[ 1843.499203] RSP: 002b:00007ffcb73bca38 EFLAGS: 00000202 ORIG_RAX: 00000000000000be
[ 1843.500210] RAX: ffffffffffffffda RBX: 00007ffcb73bda9d RCX: 00007fa7a8a7707a
[ 1843.501170] RDX: 00007ffcb73bda9d RSI: 00000000006dc050 RDI: 0000000000000003
[ 1843.502152] RBP: 00000000006dc050 R08: 0000000000000000 R09: 0000000000000000
[ 1843.503109] R10: 0000000000000002 R11: 0000000000000202 R12: 00007ffcb73bda91
[ 1843.504055] R13: 0000000000000003 R14: 00007ffcb73bda82 R15: ffffffffffffffff
[ 1843.505268] Allocated by task 3979:
[ 1843.505771] save_stack+0x19/0x80
[ 1843.506211] __kasan_kmalloc.constprop.5+0xa0/0xd0
[ 1843.506836] setxattr+0xeb/0x230
[ 1843.507264] __x64_sys_fsetxattr+0xba/0xe0
[ 1843.507886] do_syscall_64+0x6c/0x230
[ 1843.508429] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1843.509558] Freed by task 0:
[ 1843.510188] (stack is not available)
[ 1843.511309] The buggy address belongs to the object at ffff888111e369e0
which belongs to the cache kmalloc-8 of size 8
[ 1843.514095] The buggy address is located 2 bytes inside of
8-byte region [ffff888111e369e0, ffff888111e369e8)
[ 1843.516524] The buggy address belongs to the page:
[ 1843.517561] page:ffff88813f478d80 refcount:1 mapcount:0 mapping:ffff88811940c300 index:0xffff888111e373b8 compound_mapcount: 0
[ 1843.519993] flags: 0x4404000010200(slab|head)
[ 1843.520951] raw: 0004404000010200 ffff88813f48b008 ffff888119403d50 ffff88811940c300
[ 1843.522616] raw: ffff888111e373b8 000000000016000f 00000001ffffffff 0000000000000000
[ 1843.524281] page dumped because: kasan: bad access detected
[ 1843.525936] Memory state around the buggy address:
[ 1843.526975] ffff888111e36880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.528479] ffff888111e36900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.530138] >ffff888111e36980: fc fc fc fc fc fc fc fc fc fc fc fc 02 fc fc fc
[ 1843.531877] ^
[ 1843.533287] ffff888111e36a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.534874] ffff888111e36a80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1843.536468] ==================================================================
This is caused by supplying a too short compression value ('lz') in the
test-case and comparing it to 'lzo' with strncmp() and a length of 3.
strncmp() read past the 'lz' when looking for the 'o' and thus caused an
out-of-bounds read.
Introduce a new check 'btrfs_compress_is_valid_type()' which not only
checks the user-supplied value against known compression types, but also
employs checks for too short values.
Reported-by: Nikolay Borisov <nborisov@suse.com>
Fixes: 272e5326c783 ("btrfs: prop: fix vanished compression property after failed set")
CC: stable@vger.kernel.org # 5.1+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
RDMA/srp: Accept again source addresses that do not have a port number
[ Upstream commit bcef5b7215681250c4bf8961dfe15e9e4fef97d0 ]
The function srp_parse_in() is used both for parsing source address
specifications and for target address specifications. Target addresses
must have a port number. Having to specify a port number for source
addresses is inconvenient. Make sure that srp_parse_in() supports again
parsing addresses with no port number.
Cc: <stable@vger.kernel.org>
Fixes: c62adb7def71 ("IB/srp: Fix IPv6 address parsing")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcef5b7215681250c4bf8961dfe15e9e4fef97d0 ]
The function srp_parse_in() is used both for parsing source address
specifications and for target address specifications. Target addresses
must have a port number. Having to specify a port number for source
addresses is inconvenient. Make sure that srp_parse_in() supports again
parsing addresses with no port number.
Cc: <stable@vger.kernel.org>
Fixes: c62adb7def71 ("IB/srp: Fix IPv6 address parsing")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
RDMA/srp: Document srp_parse_in() arguments
[ Upstream commit e37df2d5b569390e3b80ebed9a73fd5b9dcda010 ]
This patch avoids that a warning is reported when building with W=1.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e37df2d5b569390e3b80ebed9a73fd5b9dcda010 ]
This patch avoids that a warning is reported when building with W=1.
Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: gemini: Set DIR-685 SPI CS as active low
[ Upstream commit f90b8fda3a9d72a9422ea80ae95843697f94ea4a ]
The SPI to the display on the DIR-685 is active low, we were
just saved by the SPI library enforcing active low on everything
before, so set it as active low to avoid ambiguity.
Link: https://lore.kernel.org/r/20190715202101.16060-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f90b8fda3a9d72a9422ea80ae95843697f94ea4a ]
The SPI to the display on the DIR-685 is active low, we were
just saved by the SPI library enforcing active low on everything
before, so set it as active low to avoid ambiguity.
Link: https://lore.kernel.org/r/20190715202101.16060-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM: PPC: Book3S HV: Fix CR0 setting in TM emulation
[ Upstream commit 3fefd1cd95df04da67c83c1cb93b663f04b3324f ]
When emulating tsr, treclaim and trechkpt, we incorrectly set CR0. The
code currently sets:
CR0 <- 00 || MSR[TS]
but according to the ISA it should be:
CR0 <- 0 || MSR[TS] || 0
This fixes the bit shift to put the bits in the correct location.
This is a data integrity issue as CR0 is corrupted.
Fixes: 4bb3c7a0208f ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Cc: stable@vger.kernel.org # v4.17+
Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fefd1cd95df04da67c83c1cb93b663f04b3324f ]
When emulating tsr, treclaim and trechkpt, we incorrectly set CR0. The
code currently sets:
CR0 <- 00 || MSR[TS]
but according to the ISA it should be:
CR0 <- 0 || MSR[TS] || 0
This fixes the bit shift to put the bits in the correct location.
This is a data integrity issue as CR0 is corrupted.
Fixes: 4bb3c7a0208f ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Cc: stable@vger.kernel.org # v4.17+
Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM: PPC: Use ccr field in pt_regs struct embedded in vcpu struct
[ Upstream commit fd0944baad806dfb4c777124ec712c55b714ff51 ]
When the 'regs' field was added to struct kvm_vcpu_arch, the code
was changed to use several of the fields inside regs (e.g., gpr, lr,
etc.) but not the ccr field, because the ccr field in struct pt_regs
is 64 bits on 64-bit platforms, but the cr field in kvm_vcpu_arch is
only 32 bits. This changes the code to use the regs.ccr field
instead of cr, and changes the assembly code on 64-bit platforms to
use 64-bit loads and stores instead of 32-bit ones.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd0944baad806dfb4c777124ec712c55b714ff51 ]
When the 'regs' field was added to struct kvm_vcpu_arch, the code
was changed to use several of the fields inside regs (e.g., gpr, lr,
etc.) but not the ccr field, because the ccr field in struct pt_regs
is 64 bits on 64-bit platforms, but the cr field in kvm_vcpu_arch is
only 32 bits. This changes the code to use the regs.ccr field
instead of cr, and changes the assembly code on 64-bit platforms to
use 64-bit loads and stores instead of 32-bit ones.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM: VMX: check CPUID before allowing read/write of IA32_XSS
[ Upstream commit 4d763b168e9c5c366b05812c7bba7662e5ea3669 ]
Raise #GP when guest read/write IA32_XSS, but the CPUID bits
say that it shouldn't exist.
Fixes: 203000993de5 (kvm: vmx: add MSR logic for XSAVES)
Reported-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Reported-by: Tao Xu <tao3.xu@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d763b168e9c5c366b05812c7bba7662e5ea3669 ]
Raise #GP when guest read/write IA32_XSS, but the CPUID bits
say that it shouldn't exist.
Fixes: 203000993de5 (kvm: vmx: add MSR logic for XSAVES)
Reported-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Reported-by: Tao Xu <tao3.xu@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM: VMX: Fix handling of #MC that occurs during VM-Entry
[ Upstream commit beb8d93b3e423043e079ef3dda19dad7b28467a8 ]
A previous fix to prevent KVM from consuming stale VMCS state after a
failed VM-Entry inadvertantly blocked KVM's handling of machine checks
that occur during VM-Entry.
Per Intel's SDM, a #MC during VM-Entry is handled in one of three ways,
depending on when the #MC is recognoized. As it pertains to this bug
fix, the third case explicitly states EXIT_REASON_MCE_DURING_VMENTRY
is handled like any other VM-Exit during VM-Entry, i.e. sets bit 31 to
indicate the VM-Entry failed.
If a machine-check event occurs during a VM entry, one of the following occurs:
- The machine-check event is handled as if it occurred before the VM entry:
...
- The machine-check event is handled after VM entry completes:
...
- A VM-entry failure occurs as described in Section 26.7. The basic
exit reason is 41, for "VM-entry failure due to machine-check event".
Explicitly handle EXIT_REASON_MCE_DURING_VMENTRY as a one-off case in
vmx_vcpu_run() instead of binning it into vmx_complete_atomic_exit().
Doing so allows vmx_vcpu_run() to handle VMX_EXIT_REASONS_FAILED_VMENTRY
in a sane fashion and also simplifies vmx_complete_atomic_exit() since
VMCS.VM_EXIT_INTR_INFO is guaranteed to be fresh.
Fixes: b060ca3b2e9e7 ("kvm: vmx: Handle VMLAUNCH/VMRESUME failure properly")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beb8d93b3e423043e079ef3dda19dad7b28467a8 ]
A previous fix to prevent KVM from consuming stale VMCS state after a
failed VM-Entry inadvertantly blocked KVM's handling of machine checks
that occur during VM-Entry.
Per Intel's SDM, a #MC during VM-Entry is handled in one of three ways,
depending on when the #MC is recognoized. As it pertains to this bug
fix, the third case explicitly states EXIT_REASON_MCE_DURING_VMENTRY
is handled like any other VM-Exit during VM-Entry, i.e. sets bit 31 to
indicate the VM-Entry failed.
If a machine-check event occurs during a VM entry, one of the following occurs:
- The machine-check event is handled as if it occurred before the VM entry:
...
- The machine-check event is handled after VM entry completes:
...
- A VM-entry failure occurs as described in Section 26.7. The basic
exit reason is 41, for "VM-entry failure due to machine-check event".
Explicitly handle EXIT_REASON_MCE_DURING_VMENTRY as a one-off case in
vmx_vcpu_run() instead of binning it into vmx_complete_atomic_exit().
Doing so allows vmx_vcpu_run() to handle VMX_EXIT_REASONS_FAILED_VMENTRY
in a sane fashion and also simplifies vmx_complete_atomic_exit() since
VMCS.VM_EXIT_INTR_INFO is guaranteed to be fresh.
Fixes: b060ca3b2e9e7 ("kvm: vmx: Handle VMLAUNCH/VMRESUME failure properly")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM: VMX: Always signal #GP on WRMSR to MSR_IA32_CR_PAT with bad value
[ Upstream commit d28f4290b53a157191ed9991ad05dffe9e8c0c89 ]
The behavior of WRMSR is in no way dependent on whether or not KVM
consumes the value.
Fixes: 4566654bb9be9 ("KVM: vmx: Inject #GP on invalid PAT CR")
Cc: stable@vger.kernel.org
Cc: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d28f4290b53a157191ed9991ad05dffe9e8c0c89 ]
The behavior of WRMSR is in no way dependent on whether or not KVM
consumes the value.
Fixes: 4566654bb9be9 ("KVM: vmx: Inject #GP on invalid PAT CR")
Cc: stable@vger.kernel.org
Cc: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM: x86: optimize check for valid PAT value
[ Upstream commit 674ea351cdeb01d2740edce31db7f2d79ce6095d ]
This check will soon be done on every nested vmentry and vmexit,
"parallelize" it using bitwise operations.
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 674ea351cdeb01d2740edce31db7f2d79ce6095d ]
This check will soon be done on every nested vmentry and vmexit,
"parallelize" it using bitwise operations.
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ceph: use ceph_evict_inode to cleanup inode's resource
[ Upstream commit 87bc5b895d94a0f40fe170d4cf5771c8e8f85d15 ]
remove_session_caps() relies on __wait_on_freeing_inode(), to wait for
freeing inode to remove its caps. But VFS wakes freeing inode waiters
before calling destroy_inode().
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/40102
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87bc5b895d94a0f40fe170d4cf5771c8e8f85d15 ]
remove_session_caps() relies on __wait_on_freeing_inode(), to wait for
freeing inode to remove its caps. But VFS wakes freeing inode waiters
before calling destroy_inode().
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/40102
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ALSA: hda - Don't resume forcibly i915 HDMI/DP codec
[ Upstream commit 4914da2fb0c89205790503f20dfdde854f3afdd8 ]
We apply the codec resume forcibly at system resume callback for
updating and syncing the jack detection state that may have changed
during sleeping. This is, however, superfluous for the codec like
Intel HDMI/DP, where the jack detection is managed via the audio
component notification; i.e. the jack state change shall be reported
sooner or later from the graphics side at mode change.
This patch changes the codec resume callback to avoid the forcible
resume conditionally with a new flag, codec->relaxed_resume, for
reducing the resume time. The flag is set in the codec probe.
Although this doesn't fix the entire bug mentioned in the bugzilla
entry below, it's still a good optimization and some improvements are
seen.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201901
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4914da2fb0c89205790503f20dfdde854f3afdd8 ]
We apply the codec resume forcibly at system resume callback for
updating and syncing the jack detection state that may have changed
during sleeping. This is, however, superfluous for the codec like
Intel HDMI/DP, where the jack detection is managed via the audio
component notification; i.e. the jack state change shall be reported
sooner or later from the graphics side at mode change.
This patch changes the codec resume callback to avoid the forcible
resume conditionally with a new flag, codec->relaxed_resume, for
reducing the resume time. The flag is set in the codec probe.
Although this doesn't fix the entire bug mentioned in the bugzilla
entry below, it's still a good optimization and some improvements are
seen.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201901
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
cifs: Properly handle auto disabling of serverino option
[ Upstream commit 29fbeb7a908a60a5ae8c50fbe171cb8fdcef1980 ]
Fix mount options comparison when serverino option is turned off later
in cifs_autodisable_serverino() and thus avoiding mismatch of new cifs
mounts.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (SUSE) <paulo@paulo.ac>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilove@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29fbeb7a908a60a5ae8c50fbe171cb8fdcef1980 ]
Fix mount options comparison when serverino option is turned off later
in cifs_autodisable_serverino() and thus avoiding mismatch of new cifs
mounts.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (SUSE) <paulo@paulo.ac>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilove@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
[ Upstream commit 106d45f350c7cac876844dc685845cba4ffdb70b ]
When tracing instances where we open and close WKA ports, we also pass the
request-ID of the respective FSF command.
But after successfully sending the FSF command we must not use the
request-object anymore, as this might result in an use-after-free (see
"zfcp: fix request object use-after-free in send path causing seqno
errors" ).
To fix this add a new variable that caches the request-ID before sending
the request. This won't change during the hand-off to the FCP channel,
and so it's safe to trace this cached request-ID later, instead of using
the request object.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 106d45f350c7cac876844dc685845cba4ffdb70b ]
When tracing instances where we open and close WKA ports, we also pass the
request-ID of the respective FSF command.
But after successfully sending the FSF command we must not use the
request-object anymore, as this might result in an use-after-free (see
"zfcp: fix request object use-after-free in send path causing seqno
errors" ).
To fix this add a new variable that caches the request-ID before sending
the request. This won't change during the hand-off to the FCP channel,
and so it's safe to trace this cached request-ID later, instead of using
the request object.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
staging: wilc1000: fix error path cleanup in wilc_wlan_initialize()
[ Upstream commit 6419f818ababebc1116fb2d0e220bd4fe835d0e3 ]
For the error path in wilc_wlan_initialize(), the resources are not
cleanup in the correct order. Reverted the previous changes and use the
correct order to free during error condition.
Fixes: b46d68825c2d ("staging: wilc1000: remove COMPLEMENT_BOOT")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6419f818ababebc1116fb2d0e220bd4fe835d0e3 ]
For the error path in wilc_wlan_initialize(), the resources are not
cleanup in the correct order. Reverted the previous changes and use the
correct order to free during error condition.
Fixes: b46d68825c2d ("staging: wilc1000: remove COMPLEMENT_BOOT")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
scsi: target/iblock: Fix overrun in WRITE SAME emulation
[ Upstream commit 5676234f20fef02f6ca9bd66c63a8860fce62645 ]
WRITE SAME corrupts data on the block device behind iblock if the command
is emulated. The emulation code issues (M - 1) * N times more bios than
requested, where M is the number of 512 blocks per real block size and N is
the NUMBER OF LOGICAL BLOCKS specified in WRITE SAME command. So, for a
device with 4k blocks, 7 * N more LBAs gets written after the requested
range.
The issue happens because the number of 512 byte sectors to be written is
decreased one by one while the real bios are typically from 1 to 8 512 byte
sectors per bio.
Fixes: c66ac9db8d4a ("[SCSI] target: Add LIO target core v4.0.0-rc6")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5676234f20fef02f6ca9bd66c63a8860fce62645 ]
WRITE SAME corrupts data on the block device behind iblock if the command
is emulated. The emulation code issues (M - 1) * N times more bios than
requested, where M is the number of 512 blocks per real block size and N is
the NUMBER OF LOGICAL BLOCKS specified in WRITE SAME command. So, for a
device with 4k blocks, 7 * N more LBAs gets written after the requested
range.
The issue happens because the number of 512 byte sectors to be written is
decreased one by one while the real bios are typically from 1 to 8 512 byte
sectors per bio.
Fixes: c66ac9db8d4a ("[SCSI] target: Add LIO target core v4.0.0-rc6")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
scsi: target/core: Use the SECTOR_SHIFT constant
[ Upstream commit 80b045b385cfef10939c913fbfeb19ce5491c1f2 ]
Instead of duplicating the SECTOR_SHIFT definition from <linux/blkdev.h>,
use it. This patch does not change any functionality.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80b045b385cfef10939c913fbfeb19ce5491c1f2 ]
Instead of duplicating the SECTOR_SHIFT definition from <linux/blkdev.h>,
use it. This patch does not change any functionality.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
apparmor: reset pos on failure to unpack for various functions
[ Upstream commit 156e42996bd84eccb6acf319f19ce0cb140d00e3 ]
Each function that manipulates the aa_ext struct should reset it's "pos"
member on failure. This ensures that, on failure, no changes are made to
the state of the aa_ext struct.
There are paths were elements are optional and the error path is
used to indicate the optional element is not present. This means
instead of just aborting on error the unpack stream can become
unsynchronized on optional elements, if using one of the affected
functions.
Cc: stable@vger.kernel.org
Fixes: 736ec752d95e ("AppArmor: policy routines for loading and unpacking policy")
Signed-off-by: Mike Salvatore <mike.salvatore@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 156e42996bd84eccb6acf319f19ce0cb140d00e3 ]
Each function that manipulates the aa_ext struct should reset it's "pos"
member on failure. This ensures that, on failure, no changes are made to
the state of the aa_ext struct.
There are paths were elements are optional and the error path is
used to indicate the optional element is not present. This means
instead of just aborting on error the unpack stream can become
unsynchronized on optional elements, if using one of the affected
functions.
Cc: stable@vger.kernel.org
Fixes: 736ec752d95e ("AppArmor: policy routines for loading and unpacking policy")
Signed-off-by: Mike Salvatore <mike.salvatore@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
IB/hfi1: Avoid hardlockup with flushlist_lock
[ Upstream commit cf131a81967583ae737df6383a0893b9fee75b4e ]
Heavy contention of the sde flushlist_lock can cause hard lockups at
extreme scale when the flushing logic is under stress.
Mitigate by replacing the item at a time copy to the local list with
an O(1) list_splice_init() and using the high priority work queue to
do the flushes.
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf131a81967583ae737df6383a0893b9fee75b4e ]
Heavy contention of the sde flushlist_lock can cause hard lockups at
extreme scale when the flushing logic is under stress.
Mitigate by replacing the item at a time copy to the local list with
an O(1) list_splice_init() and using the high priority work queue to
do the flushes.
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
clk: tegra210: Fix default rates for HDA clocks
[ Upstream commit 9caec6620f25b6d15646bbdb93062c872ba3b56f ]
Currently the default clock rates for the HDA and HDA2CODEC_2X clocks
are both 19.2MHz. However, the default rates for these clocks should
actually be 51MHz and 48MHz, respectively. The current clock settings
results in a distorted output during audio playback. Correct the default
clock rates for these clocks by specifying them in the clock init table
for Tegra210.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9caec6620f25b6d15646bbdb93062c872ba3b56f ]
Currently the default clock rates for the HDA and HDA2CODEC_2X clocks
are both 19.2MHz. However, the default rates for these clocks should
actually be 51MHz and 48MHz, respectively. The current clock settings
results in a distorted output during audio playback. Correct the default
clock rates for these clocks by specifying them in the clock init table
for Tegra210.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
clk: tegra: Fix maximum audio sync clock for Tegra124/210
[ Upstream commit 845d782d91448e0fbca686bca2cc9f9c2a9ba3e7 ]
The maximum frequency supported for I2S on Tegra124 and Tegra210 is
24.576MHz (as stated in the Tegra TK1 data sheet for Tegra124 and the
Jetson TX1 module data sheet for Tegra210). However, the maximum I2S
frequency is limited to 24MHz because that is the maximum frequency of
the audio sync clock. Increase the maximum audio sync clock frequency
to 24.576MHz for Tegra124 and Tegra210 in order to support 24.576MHz
for I2S.
Update the tegra_clk_register_sync_source() function so that it does
not set the initial rate for the sync clocks and use the clock init
tables to set the initial rate instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 845d782d91448e0fbca686bca2cc9f9c2a9ba3e7 ]
The maximum frequency supported for I2S on Tegra124 and Tegra210 is
24.576MHz (as stated in the Tegra TK1 data sheet for Tegra124 and the
Jetson TX1 module data sheet for Tegra210). However, the maximum I2S
frequency is limited to 24MHz because that is the maximum frequency of
the audio sync clock. Increase the maximum audio sync clock frequency
to 24.576MHz for Tegra124 and Tegra210 in order to support 24.576MHz
for I2S.
Update the tegra_clk_register_sync_source() function so that it does
not set the initial rate for the sync clocks and use the clock init
tables to set the initial rate instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
cifs: add spinlock for the openFileList to cifsInodeInfo
[ Upstream commit 487317c99477d00f22370625d53be3239febabbe ]
We can not depend on the tcon->open_file_lock here since in multiuser mode
we may have the same file/inode open via multiple different tcons.
The current code is race prone and will crash if one user deletes a file
at the same time a different user opens/create the file.
To avoid this we need to have a spinlock attached to the inode and not the tcon.
RHBZ: 1580165
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 487317c99477d00f22370625d53be3239febabbe ]
We can not depend on the tcon->open_file_lock here since in multiuser mode
we may have the same file/inode open via multiple different tcons.
The current code is race prone and will crash if one user deletes a file
at the same time a different user opens/create the file.
To avoid this we need to have a spinlock attached to the inode and not the tcon.
RHBZ: 1580165
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Btrfs: fix race between block group removal and block group allocation
[ Upstream commit 8eaf40c0e24e98899a0f3ac9d25a33aafe13822a ]
If a task is removing the block group that currently has the highest start
offset amongst all existing block groups, there is a short time window
where it races with a concurrent block group allocation, resulting in a
transaction abort with an error code of EEXIST.
The following diagram explains the race in detail:
Task A Task B
btrfs_remove_block_group(bg offset X)
remove_extent_mapping(em offset X)
-> removes extent map X from the
tree of extent maps
(fs_info->mapping_tree), so the
next call to find_next_chunk()
will return offset X
btrfs_alloc_chunk()
find_next_chunk()
--> returns offset X
__btrfs_alloc_chunk(offset X)
btrfs_make_block_group()
btrfs_create_block_group_cache()
--> creates btrfs_block_group_cache
object with a key corresponding
to the block group item in the
extent, the key is:
(offset X, BTRFS_BLOCK_GROUP_ITEM_KEY, 1G)
--> adds the btrfs_block_group_cache object
to the list new_bgs of the transaction
handle
btrfs_end_transaction(trans handle)
__btrfs_end_transaction()
btrfs_create_pending_block_groups()
--> sees the new btrfs_block_group_cache
in the new_bgs list of the transaction
handle
--> its call to btrfs_insert_item() fails
with -EEXIST when attempting to insert
the block group item key
(offset X, BTRFS_BLOCK_GROUP_ITEM_KEY, 1G)
because task A has not removed that key yet
--> aborts the running transaction with
error -EEXIST
btrfs_del_item()
-> removes the block group's key from
the extent tree, key is
(offset X, BTRFS_BLOCK_GROUP_ITEM_KEY, 1G)
A sample transaction abort trace:
[78912.403537] ------------[ cut here ]------------
[78912.403811] BTRFS: Transaction aborted (error -17)
[78912.404082] WARNING: CPU: 2 PID: 20465 at fs/btrfs/extent-tree.c:10551 btrfs_create_pending_block_groups+0x196/0x250 [btrfs]
(...)
[78912.405642] CPU: 2 PID: 20465 Comm: btrfs Tainted: G W 5.0.0-btrfs-next-46 #1
[78912.405941] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626ccb91-prebuilt.qemu-project.org 04/01/2014
[78912.406586] RIP: 0010:btrfs_create_pending_block_groups+0x196/0x250 [btrfs]
(...)
[78912.407636] RSP: 0018:ffff9d3d4b7e3b08 EFLAGS: 00010282
[78912.407997] RAX: 0000000000000000 RBX: ffff90959a3796f0 RCX: 0000000000000006
[78912.408369] RDX: 0000000000000007 RSI: 0000000000000001 RDI: ffff909636b16860
[78912.408746] RBP: ffff909626758a58 R08: 0000000000000000 R09: 0000000000000000
[78912.409144] R10: ffff9095ff462400 R11: 0000000000000000 R12: ffff90959a379588
[78912.409521] R13: ffff909626758ab0 R14: ffff9095036c0000 R15: ffff9095299e1158
[78912.409899] FS: 00007f387f16f700(0000) GS:ffff909636b00000(0000) knlGS:0000000000000000
[78912.410285] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[78912.410673] CR2: 00007f429fc87cbc CR3: 000000014440a004 CR4: 00000000003606e0
[78912.411095] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[78912.411496] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[78912.411898] Call Trace:
[78912.412318] __btrfs_end_transaction+0x5b/0x1c0 [btrfs]
[78912.412746] btrfs_inc_block_group_ro+0xcf/0x160 [btrfs]
[78912.413179] scrub_enumerate_chunks+0x188/0x5b0 [btrfs]
[78912.413622] ? __mutex_unlock_slowpath+0x100/0x2a0
[78912.414078] btrfs_scrub_dev+0x2ef/0x720 [btrfs]
[78912.414535] ? __sb_start_write+0xd4/0x1c0
[78912.414963] ? mnt_want_write_file+0x24/0x50
[78912.415403] btrfs_ioctl+0x17fb/0x3120 [btrfs]
[78912.415832] ? lock_acquire+0xa6/0x190
[78912.416256] ? do_vfs_ioctl+0xa2/0x6f0
[78912.416685] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[78912.417116] do_vfs_ioctl+0xa2/0x6f0
[78912.417534] ? __fget+0x113/0x200
[78912.417954] ksys_ioctl+0x70/0x80
[78912.418369] __x64_sys_ioctl+0x16/0x20
[78912.418812] do_syscall_64+0x60/0x1b0
[78912.419231] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[78912.419644] RIP: 0033:0x7f3880252dd7
(...)
[78912.420957] RSP: 002b:00007f387f16ed68 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[78912.421426] RAX: ffffffffffffffda RBX: 000055f5becc1df0 RCX: 00007f3880252dd7
[78912.421889] RDX: 000055f5becc1df0 RSI: 00000000c400941b RDI: 0000000000000003
[78912.422354] RBP: 0000000000000000 R08: 00007f387f16f700 R09: 0000000000000000
[78912.422790] R10: 00007f387f16f700 R11: 0000000000000246 R12: 0000000000000000
[78912.423202] R13: 00007ffda49c266f R14: 0000000000000000 R15: 00007f388145e040
[78912.425505] ---[ end trace eb9bfe7c426fc4d3 ]---
Fix this by calling remove_extent_mapping(), at btrfs_remove_block_group(),
only at the very end, after removing the block group item key from the
extent tree (and removing the free space tree entry if we are using the
free space tree feature).
Fixes: 04216820fe83d5 ("Btrfs: fix race between fs trimming and block group remove/allocation")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8eaf40c0e24e98899a0f3ac9d25a33aafe13822a ]
If a task is removing the block group that currently has the highest start
offset amongst all existing block groups, there is a short time window
where it races with a concurrent block group allocation, resulting in a
transaction abort with an error code of EEXIST.
The following diagram explains the race in detail:
Task A Task B
btrfs_remove_block_group(bg offset X)
remove_extent_mapping(em offset X)
-> removes extent map X from the
tree of extent maps
(fs_info->mapping_tree), so the
next call to find_next_chunk()
will return offset X
btrfs_alloc_chunk()
find_next_chunk()
--> returns offset X
__btrfs_alloc_chunk(offset X)
btrfs_make_block_group()
btrfs_create_block_group_cache()
--> creates btrfs_block_group_cache
object with a key corresponding
to the block group item in the
extent, the key is:
(offset X, BTRFS_BLOCK_GROUP_ITEM_KEY, 1G)
--> adds the btrfs_block_group_cache object
to the list new_bgs of the transaction
handle
btrfs_end_transaction(trans handle)
__btrfs_end_transaction()
btrfs_create_pending_block_groups()
--> sees the new btrfs_block_group_cache
in the new_bgs list of the transaction
handle
--> its call to btrfs_insert_item() fails
with -EEXIST when attempting to insert
the block group item key
(offset X, BTRFS_BLOCK_GROUP_ITEM_KEY, 1G)
because task A has not removed that key yet
--> aborts the running transaction with
error -EEXIST
btrfs_del_item()
-> removes the block group's key from
the extent tree, key is
(offset X, BTRFS_BLOCK_GROUP_ITEM_KEY, 1G)
A sample transaction abort trace:
[78912.403537] ------------[ cut here ]------------
[78912.403811] BTRFS: Transaction aborted (error -17)
[78912.404082] WARNING: CPU: 2 PID: 20465 at fs/btrfs/extent-tree.c:10551 btrfs_create_pending_block_groups+0x196/0x250 [btrfs]
(...)
[78912.405642] CPU: 2 PID: 20465 Comm: btrfs Tainted: G W 5.0.0-btrfs-next-46 #1
[78912.405941] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626ccb91-prebuilt.qemu-project.org 04/01/2014
[78912.406586] RIP: 0010:btrfs_create_pending_block_groups+0x196/0x250 [btrfs]
(...)
[78912.407636] RSP: 0018:ffff9d3d4b7e3b08 EFLAGS: 00010282
[78912.407997] RAX: 0000000000000000 RBX: ffff90959a3796f0 RCX: 0000000000000006
[78912.408369] RDX: 0000000000000007 RSI: 0000000000000001 RDI: ffff909636b16860
[78912.408746] RBP: ffff909626758a58 R08: 0000000000000000 R09: 0000000000000000
[78912.409144] R10: ffff9095ff462400 R11: 0000000000000000 R12: ffff90959a379588
[78912.409521] R13: ffff909626758ab0 R14: ffff9095036c0000 R15: ffff9095299e1158
[78912.409899] FS: 00007f387f16f700(0000) GS:ffff909636b00000(0000) knlGS:0000000000000000
[78912.410285] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[78912.410673] CR2: 00007f429fc87cbc CR3: 000000014440a004 CR4: 00000000003606e0
[78912.411095] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[78912.411496] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[78912.411898] Call Trace:
[78912.412318] __btrfs_end_transaction+0x5b/0x1c0 [btrfs]
[78912.412746] btrfs_inc_block_group_ro+0xcf/0x160 [btrfs]
[78912.413179] scrub_enumerate_chunks+0x188/0x5b0 [btrfs]
[78912.413622] ? __mutex_unlock_slowpath+0x100/0x2a0
[78912.414078] btrfs_scrub_dev+0x2ef/0x720 [btrfs]
[78912.414535] ? __sb_start_write+0xd4/0x1c0
[78912.414963] ? mnt_want_write_file+0x24/0x50
[78912.415403] btrfs_ioctl+0x17fb/0x3120 [btrfs]
[78912.415832] ? lock_acquire+0xa6/0x190
[78912.416256] ? do_vfs_ioctl+0xa2/0x6f0
[78912.416685] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[78912.417116] do_vfs_ioctl+0xa2/0x6f0
[78912.417534] ? __fget+0x113/0x200
[78912.417954] ksys_ioctl+0x70/0x80
[78912.418369] __x64_sys_ioctl+0x16/0x20
[78912.418812] do_syscall_64+0x60/0x1b0
[78912.419231] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[78912.419644] RIP: 0033:0x7f3880252dd7
(...)
[78912.420957] RSP: 002b:00007f387f16ed68 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[78912.421426] RAX: ffffffffffffffda RBX: 000055f5becc1df0 RCX: 00007f3880252dd7
[78912.421889] RDX: 000055f5becc1df0 RSI: 00000000c400941b RDI: 0000000000000003
[78912.422354] RBP: 0000000000000000 R08: 00007f387f16f700 R09: 0000000000000000
[78912.422790] R10: 00007f387f16f700 R11: 0000000000000246 R12: 0000000000000000
[78912.423202] R13: 00007ffda49c266f R14: 0000000000000000 R15: 00007f388145e040
[78912.425505] ---[ end trace eb9bfe7c426fc4d3 ]---
Fix this by calling remove_extent_mapping(), at btrfs_remove_block_group(),
only at the very end, after removing the block group item key from the
extent tree (and removing the free space tree entry if we are using the
free space tree feature).
Fixes: 04216820fe83d5 ("Btrfs: fix race between fs trimming and block group remove/allocation")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
drm/amdgpu/{uvd,vcn}: fetch ring's read_ptr after alloc
[ Upstream commit 517b91f4cde3043d77b2178548473e8545ef07cb ]
[What]
readptr read always returns zero, since most likely
these blocks are either power or clock gated.
[How]
fetch rptr after amdgpu_ring_alloc() which informs
the power management code that the block is about to be
used and hence the gating is turned off.
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 517b91f4cde3043d77b2178548473e8545ef07cb ]
[What]
readptr read always returns zero, since most likely
these blocks are either power or clock gated.
[How]
fetch rptr after amdgpu_ring_alloc() which informs
the power management code that the block is about to be
used and hence the gating is turned off.
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
drm/amdgpu: fix ring test failure issue during s3 in vce 3.0 (V2)
[ Upstream commit ce0e22f5d886d1b56c7ab4347c45b9ac5fcc058d ]
[What]
vce ring test fails consistently during resume in s3 cycle, due to
mismatch read & write pointers.
On debug/analysis its found that rptr to be compared is not being
correctly updated/read, which leads to this failure.
Below is the failure signature:
[drm:amdgpu_vce_ring_test_ring] *ERROR* amdgpu: ring 12 test failed
[drm:amdgpu_device_ip_resume_phase2] *ERROR* resume of IP block <vce_v3_0> failed -110
[drm:amdgpu_device_resume] *ERROR* amdgpu_device_ip_resume failed (-110).
[How]
fetch rptr appropriately, meaning move its read location further down
in the code flow.
With this patch applied the s3 failure is no more seen for >5k s3 cycles,
which otherwise is pretty consistent.
V2: remove reduntant fetch of rptr
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce0e22f5d886d1b56c7ab4347c45b9ac5fcc058d ]
[What]
vce ring test fails consistently during resume in s3 cycle, due to
mismatch read & write pointers.
On debug/analysis its found that rptr to be compared is not being
correctly updated/read, which leads to this failure.
Below is the failure signature:
[drm:amdgpu_vce_ring_test_ring] *ERROR* amdgpu: ring 12 test failed
[drm:amdgpu_device_ip_resume_phase2] *ERROR* resume of IP block <vce_v3_0> failed -110
[drm:amdgpu_device_resume] *ERROR* amdgpu_device_ip_resume failed (-110).
[How]
fetch rptr appropriately, meaning move its read location further down
in the code flow.
With this patch applied the s3 failure is no more seen for >5k s3 cycles,
which otherwise is pretty consistent.
V2: remove reduntant fetch of rptr
Signed-off-by: Louis Li <Ching-shih.Li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
kvm: Check irqchip mode before assign irqfd
[ Upstream commit 654f1f13ea56b92bacade8ce2725aea0457f91c0 ]
When assigning kvm irqfd we didn't check the irqchip mode but we allow
KVM_IRQFD to succeed with all the irqchip modes. However it does not
make much sense to create irqfd even without the kernel chips. Let's
provide a arch-dependent helper to check whether a specific irqfd is
allowed by the arch. At least for x86, it should make sense to check:
- when irqchip mode is NONE, all irqfds should be disallowed, and,
- when irqchip mode is SPLIT, irqfds that are with resamplefd should
be disallowed.
For either of the case, previously we'll silently ignore the irq or
the irq ack event if the irqchip mode is incorrect. However that can
cause misterious guest behaviors and it can be hard to triage. Let's
fail KVM_IRQFD even earlier to detect these incorrect configurations.
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Radim Krčmář <rkrcmar@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 654f1f13ea56b92bacade8ce2725aea0457f91c0 ]
When assigning kvm irqfd we didn't check the irqchip mode but we allow
KVM_IRQFD to succeed with all the irqchip modes. However it does not
make much sense to create irqfd even without the kernel chips. Let's
provide a arch-dependent helper to check whether a specific irqfd is
allowed by the arch. At least for x86, it should make sense to check:
- when irqchip mode is NONE, all irqfds should be disallowed, and,
- when irqchip mode is SPLIT, irqfds that are with resamplefd should
be disallowed.
For either of the case, previously we'll silently ignore the irq or
the irq ack event if the irqchip mode is incorrect. However that can
cause misterious guest behaviors and it can be hard to triage. Let's
fail KVM_IRQFD even earlier to detect these incorrect configurations.
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Radim Krčmář <rkrcmar@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
drm/amdkfd: Add missing Polaris10 ID
[ Upstream commit 0a5a9c276c335870a1cecc4f02b76d6d6f663c8b ]
This was added to amdgpu but was missed in amdkfd
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.rg
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a5a9c276c335870a1cecc4f02b76d6d6f663c8b ]
This was added to amdgpu but was missed in amdkfd
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.rg
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARC: mm: SIGSEGV userspace trying to access kernel virtual memory
[ Upstream commit a8c715b4dd73c26a81a9cc8dc792aa715d8b4bb2 ]
As of today if userspace process tries to access a kernel virtual addres
(0x7000_0000 to 0x7ffff_ffff) such that a legit kernel mapping already
exists, that process hangs instead of being killed with SIGSEGV
Fix that by ensuring that do_page_fault() handles kenrel vaddr only if
in kernel mode.
And given this, we can also simplify the code a bit. Now a vmalloc fault
implies kernel mode so its failure (for some reason) can reuse the
@no_context label and we can remove @bad_area_nosemaphore.
Reproduce user test for original problem:
------------------------>8-----------------
#include <stdlib.h>
#include <stdint.h>
int main(int argc, char *argv[])
{
volatile uint32_t temp;
temp = *(uint32_t *)(0x70000000);
}
------------------------>8-----------------
Cc: <stable@vger.kernel.org>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8c715b4dd73c26a81a9cc8dc792aa715d8b4bb2 ]
As of today if userspace process tries to access a kernel virtual addres
(0x7000_0000 to 0x7ffff_ffff) such that a legit kernel mapping already
exists, that process hangs instead of being killed with SIGSEGV
Fix that by ensuring that do_page_fault() handles kenrel vaddr only if
in kernel mode.
And given this, we can also simplify the code a bit. Now a vmalloc fault
implies kernel mode so its failure (for some reason) can reuse the
@no_context label and we can remove @bad_area_nosemaphore.
Reproduce user test for original problem:
------------------------>8-----------------
#include <stdlib.h>
#include <stdint.h>
int main(int argc, char *argv[])
{
volatile uint32_t temp;
temp = *(uint32_t *)(0x70000000);
}
------------------------>8-----------------
Cc: <stable@vger.kernel.org>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARC: mm: fix uninitialised signal code in do_page_fault
[ Upstream commit 121e38e5acdc8e1e4cdb750fcdcc72f94e420968 ]
Commit 15773ae938d8 ("signal/arc: Use force_sig_fault where
appropriate") introduced undefined behaviour by leaving si_code
unitiailized and leaking random kernel values to user space.
Fixes: 15773ae938d8 ("signal/arc: Use force_sig_fault where appropriate")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 121e38e5acdc8e1e4cdb750fcdcc72f94e420968 ]
Commit 15773ae938d8 ("signal/arc: Use force_sig_fault where
appropriate") introduced undefined behaviour by leaving si_code
unitiailized and leaking random kernel values to user space.
Fixes: 15773ae938d8 ("signal/arc: Use force_sig_fault where appropriate")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
signal/arc: Use force_sig_fault where appropriate
[ Upstream commit 15773ae938d8d93d982461990bebad6e1d7a1830 ]
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15773ae938d8d93d982461990bebad6e1d7a1830 ]
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
dm crypt: move detailed message into debug level
[ Upstream commit 7a1cd7238fde6ab367384a4a2998cba48330c398 ]
The information about tag size should not be printed without debug info
set. Also print device major:minor in the error message to identify the
device instance.
Also use rate limiting and debug level for info about used crypto API
implementaton. This is important because during online reencryption
the existing message saturates syslog (because we are moving hotzone
across the whole device).
Cc: stable@vger.kernel.org
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a1cd7238fde6ab367384a4a2998cba48330c398 ]
The information about tag size should not be printed without debug info
set. Also print device major:minor in the error message to identify the
device instance.
Also use rate limiting and debug level for info about used crypto API
implementaton. This is important because during online reencryption
the existing message saturates syslog (because we are moving hotzone
across the whole device).
Cc: stable@vger.kernel.org
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
cifs: smbd: take an array of reqeusts when sending upper layer data
[ Upstream commit 4739f2328661d070f93f9bcc8afb2a82706c826d ]
To support compounding, __smb_send_rqst() now sends an array of requests to
the transport layer.
Change smbd_send() to take an array of requests, and send them in as few
packets as possible.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4739f2328661d070f93f9bcc8afb2a82706c826d ]
To support compounding, __smb_send_rqst() now sends an array of requests to
the transport layer.
Change smbd_send() to take an array of requests, and send them in as few
packets as possible.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
PCI: dwc: Use devm_pci_alloc_host_bridge() to simplify code
[ Upstream commit e6fdd3bf5aecd8615f31a5128775b9abcf3e0d86 ]
Use devm_pci_alloc_host_bridge() to simplify the error code path. This
also fixes a leak in the dw_pcie_host_init() error path.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
CC: stable@vger.kernel.org # v4.13+
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6fdd3bf5aecd8615f31a5128775b9abcf3e0d86 ]
Use devm_pci_alloc_host_bridge() to simplify the error code path. This
also fixes a leak in the dw_pcie_host_init() error path.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
CC: stable@vger.kernel.org # v4.13+
Signed-off-by: Sasha Levin <sashal@kernel.org>
mmc: sdhci-pci: Add support for Intel CML
[ Upstream commit 765c59675ab571caf7ada456bbfd23a73136b535 ]
Add PCI Ids for Intel CML.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 765c59675ab571caf7ada456bbfd23a73136b535 ]
Add PCI Ids for Intel CML.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
blk-mq: free hw queue's resource in hctx's release handler
[ Upstream commit c7e2d94b3d1634988a95ac4d77a72dc7487ece06 ]
Once blk_cleanup_queue() returns, tags shouldn't be used any more,
because blk_mq_free_tag_set() may be called. Commit 45a9c9d909b2
("blk-mq: Fix a use-after-free") fixes this issue exactly.
However, that commit introduces another issue. Before 45a9c9d909b2,
we are allowed to run queue during cleaning up queue if the queue's
kobj refcount is held. After that commit, queue can't be run during
queue cleaning up, otherwise oops can be triggered easily because
some fields of hctx are freed by blk_mq_free_queue() in blk_cleanup_queue().
We have invented ways for addressing this kind of issue before, such as:
8dc765d438f1 ("SCSI: fix queue cleanup race before queue initialization is done")
c2856ae2f315 ("blk-mq: quiesce queue before freeing queue")
But still can't cover all cases, recently James reports another such
kind of issue:
https://marc.info/?l=linux-scsi&m=155389088124782&w=2
This issue can be quite hard to address by previous way, given
scsi_run_queue() may run requeues for other LUNs.
Fixes the above issue by freeing hctx's resources in its release handler, and this
way is safe becasue tags isn't needed for freeing such hctx resource.
This approach follows typical design pattern wrt. kobject's release handler.
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Reported-by: James Smart <james.smart@broadcom.com>
Fixes: 45a9c9d909b2 ("blk-mq: Fix a use-after-free")
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e2d94b3d1634988a95ac4d77a72dc7487ece06 ]
Once blk_cleanup_queue() returns, tags shouldn't be used any more,
because blk_mq_free_tag_set() may be called. Commit 45a9c9d909b2
("blk-mq: Fix a use-after-free") fixes this issue exactly.
However, that commit introduces another issue. Before 45a9c9d909b2,
we are allowed to run queue during cleaning up queue if the queue's
kobj refcount is held. After that commit, queue can't be run during
queue cleaning up, otherwise oops can be triggered easily because
some fields of hctx are freed by blk_mq_free_queue() in blk_cleanup_queue().
We have invented ways for addressing this kind of issue before, such as:
8dc765d438f1 ("SCSI: fix queue cleanup race before queue initialization is done")
c2856ae2f315 ("blk-mq: quiesce queue before freeing queue")
But still can't cover all cases, recently James reports another such
kind of issue:
https://marc.info/?l=linux-scsi&m=155389088124782&w=2
This issue can be quite hard to address by previous way, given
scsi_run_queue() may run requeues for other LUNs.
Fixes the above issue by freeing hctx's resources in its release handler, and this
way is safe becasue tags isn't needed for freeing such hctx resource.
This approach follows typical design pattern wrt. kobject's release handler.
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Reported-by: James Smart <james.smart@broadcom.com>
Fixes: 45a9c9d909b2 ("blk-mq: Fix a use-after-free")
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
dm mpath: fix missing call of path selector type->end_io
[ Upstream commit 5de719e3d01b4abe0de0d7b857148a880ff2a90b ]
After commit 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via
blk_insert_cloned_request feedback"), map_request() will requeue the tio
when issued clone request return BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE.
Thus, if device driver status is error, a tio may be requeued multiple
times until the return value is not DM_MAPIO_REQUEUE. That means
type->start_io may be called multiple times, while type->end_io is only
called when IO complete.
In fact, even without commit 396eaf21ee17, setup_clone() failure can
also cause tio requeue and associated missed call to type->end_io.
The service-time path selector selects path based on in_flight_size,
which is increased by st_start_io() and decreased by st_end_io().
Missed calls to st_end_io() can lead to in_flight_size count error and
will cause the selector to make the wrong choice. In addition,
queue-length path selector will also be affected.
To fix the problem, call type->end_io in ->release_clone_rq before tio
requeue. map_info is passed to ->release_clone_rq() for map_request()
error path that result in requeue.
Fixes: 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback")
Cc: stable@vger.kernl.org
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5de719e3d01b4abe0de0d7b857148a880ff2a90b ]
After commit 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via
blk_insert_cloned_request feedback"), map_request() will requeue the tio
when issued clone request return BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE.
Thus, if device driver status is error, a tio may be requeued multiple
times until the return value is not DM_MAPIO_REQUEUE. That means
type->start_io may be called multiple times, while type->end_io is only
called when IO complete.
In fact, even without commit 396eaf21ee17, setup_clone() failure can
also cause tio requeue and associated missed call to type->end_io.
The service-time path selector selects path based on in_flight_size,
which is increased by st_start_io() and decreased by st_end_io().
Missed calls to st_end_io() can lead to in_flight_size count error and
will cause the selector to make the wrong choice. In addition,
queue-length path selector will also be affected.
To fix the problem, call type->end_io in ->release_clone_rq before tio
requeue. map_info is passed to ->release_clone_rq() for map_request()
error path that result in requeue.
Fixes: 396eaf21ee17 ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback")
Cc: stable@vger.kernl.org
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
PCI: Reset Lenovo ThinkPad P50 nvgpu at boot if necessary
[ Upstream commit e0547c81bfcfad01cbbfa93a5e66bb98ab932f80 ]
On ThinkPad P50 SKUs with an Nvidia Quadro M1000M instead of the M2000M
variant, the BIOS does not always reset the secondary Nvidia GPU during
reboot if the laptop is configured in Hybrid Graphics mode. The reason is
unknown, but the following steps and possibly a good bit of patience will
reproduce the issue:
1. Boot up the laptop normally in Hybrid Graphics mode
2. Make sure nouveau is loaded and that the GPU is awake
3. Allow the Nvidia GPU to runtime suspend itself after being idle
4. Reboot the machine, the more sudden the better (e.g. sysrq-b may help)
5. If nouveau loads up properly, reboot the machine again and go back to
step 2 until you reproduce the issue
This results in some very strange behavior: the GPU will be left in exactly
the same state it was in when the previously booted kernel started the
reboot. This has all sorts of bad side effects: for starters, this
completely breaks nouveau starting with a mysterious EVO channel failure
that happens well before we've actually used the EVO channel for anything:
nouveau 0000:01:00.0: disp: chid 0 mthd 0000 data 00000400 00001000 00000002
This causes a timeout trying to bring up the GR ctx:
nouveau 0000:01:00.0: timeout
WARNING: CPU: 0 PID: 12 at drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgf100.c:1547 gf100_grctx_generate+0x7b2/0x850 [nouveau]
Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET82W (1.55 ) 12/18/2018
Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
...
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: fifo: fault 01 [WRITE] at 0000000000008000 engine 00 [GR] client 15 [HUB/SCC_NB] reason c4 [] on channel -1 [0000000000 unknown]
The GPU never manages to recover. Booting without loading nouveau causes
issues as well, since the GPU starts sending spurious interrupts that cause
other device's IRQs to get disabled by the kernel:
irq 16: nobody cared (try booting with the "irqpoll" option)
...
handlers:
[<000000007faa9e99>] i801_isr [i2c_i801]
Disabling IRQ #16
...
serio: RMI4 PS/2 pass-through port at rmi4-00.fn03
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-110).
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts!
This causes the touchpad and sometimes other things to get disabled.
Since this happens without nouveau, we can't fix this problem from nouveau
itself.
Add a PCI quirk for the specific P50 variant of this GPU. Make sure the
GPU is advertising NoReset- so we don't reset the GPU when the machine is
in Dedicated graphics mode (where the GPU being initialized by the BIOS is
normal and expected). Map the GPU MMIO space and read the magic 0x2240c
register, which will have bit 1 set if the device was POSTed during a
previous boot. Once we've confirmed all of this, reset the GPU and
re-disable it - bringing it back to a healthy state.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203003
Link: https://lore.kernel.org/lkml/20190212220230.1568-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: nouveau@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0547c81bfcfad01cbbfa93a5e66bb98ab932f80 ]
On ThinkPad P50 SKUs with an Nvidia Quadro M1000M instead of the M2000M
variant, the BIOS does not always reset the secondary Nvidia GPU during
reboot if the laptop is configured in Hybrid Graphics mode. The reason is
unknown, but the following steps and possibly a good bit of patience will
reproduce the issue:
1. Boot up the laptop normally in Hybrid Graphics mode
2. Make sure nouveau is loaded and that the GPU is awake
3. Allow the Nvidia GPU to runtime suspend itself after being idle
4. Reboot the machine, the more sudden the better (e.g. sysrq-b may help)
5. If nouveau loads up properly, reboot the machine again and go back to
step 2 until you reproduce the issue
This results in some very strange behavior: the GPU will be left in exactly
the same state it was in when the previously booted kernel started the
reboot. This has all sorts of bad side effects: for starters, this
completely breaks nouveau starting with a mysterious EVO channel failure
that happens well before we've actually used the EVO channel for anything:
nouveau 0000:01:00.0: disp: chid 0 mthd 0000 data 00000400 00001000 00000002
This causes a timeout trying to bring up the GR ctx:
nouveau 0000:01:00.0: timeout
WARNING: CPU: 0 PID: 12 at drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgf100.c:1547 gf100_grctx_generate+0x7b2/0x850 [nouveau]
Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET82W (1.55 ) 12/18/2018
Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
...
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: fifo: fault 01 [WRITE] at 0000000000008000 engine 00 [GR] client 15 [HUB/SCC_NB] reason c4 [] on channel -1 [0000000000 unknown]
The GPU never manages to recover. Booting without loading nouveau causes
issues as well, since the GPU starts sending spurious interrupts that cause
other device's IRQs to get disabled by the kernel:
irq 16: nobody cared (try booting with the "irqpoll" option)
...
handlers:
[<000000007faa9e99>] i801_isr [i2c_i801]
Disabling IRQ #16
...
serio: RMI4 PS/2 pass-through port at rmi4-00.fn03
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-110).
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts!
This causes the touchpad and sometimes other things to get disabled.
Since this happens without nouveau, we can't fix this problem from nouveau
itself.
Add a PCI quirk for the specific P50 variant of this GPU. Make sure the
GPU is advertising NoReset- so we don't reset the GPU when the machine is
in Dedicated graphics mode (where the GPU being initialized by the BIOS is
normal and expected). Map the GPU MMIO space and read the magic 0x2240c
register, which will have bit 1 set if the device was POSTed during a
previous boot. Once we've confirmed all of this, reset the GPU and
re-disable it - bringing it back to a healthy state.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203003
Link: https://lore.kernel.org/lkml/20190212220230.1568-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: nouveau@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
PCI: Add macro for Switchtec quirk declarations
[ Upstream commit 01d5d7fa8376c6b5acda86e16fcad22de6bba486 ]
Add SWITCHTEC_QUIRK() to reduce redundancy in declaring devices that use
quirk_switchtec_ntb_dma_alias().
By itself, this is no functional change, but a subsequent patch updates
SWITCHTEC_QUIRK() to fix ad281ecf1c7d ("PCI: Add DMA alias quirk for
Microsemi Switchtec NTB").
Fixes: ad281ecf1c7d ("PCI: Add DMA alias quirk for Microsemi Switchtec NTB")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01d5d7fa8376c6b5acda86e16fcad22de6bba486 ]
Add SWITCHTEC_QUIRK() to reduce redundancy in declaring devices that use
quirk_switchtec_ntb_dma_alias().
By itself, this is no functional change, but a subsequent patch updates
SWITCHTEC_QUIRK() to fix ad281ecf1c7d ("PCI: Add DMA alias quirk for
Microsemi Switchtec NTB").
Fixes: ad281ecf1c7d ("PCI: Add DMA alias quirk for Microsemi Switchtec NTB")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>